Self-Adhesive Hydrogels for Tissue Engineering

2021 ◽  
Author(s):  
Yating Yi ◽  
Chaoming Xie ◽  
Jin Liu ◽  
Yonghao Zheng ◽  
Jun Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Three Dimensional ◽  
Biocompatible Polymers ◽  
Tunable Mechanical Properties ◽  
Hydrophilic Network

Hydrogels consisting of a three-dimensional hydrophilic network of biocompatible polymers have been widely used in tissue engineering. Owing to their tunable mechanical properties, hydrogels have been applied in both hard...

scholarly journals Is Dialdehyde Chitosan a Good Substance to Modify Physicochemical Properties of Biopolymeric Materials?

2021 ◽  
Vol 22 (7) ◽  
pp. 3391
Author(s):  
Sylwia Grabska-Zielińska ◽  
Alina Sionkowska ◽  
Ewa Olewnik-Kruszkowska ◽  
Katarzyna Reczyńska ◽  
Elżbieta Pamuła
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Physicochemical Properties ◽  
Silk Fibroin ◽  
Three Dimensional ◽  
Microscopy Imaging ◽  
Maximum Deformation ◽  
One Step ◽  
Chitosan Blends ◽  
Fourier Transfer Infrared Spectroscopy

The aim of this work was to compare physicochemical properties of three dimensional scaffolds based on silk fibroin, collagen and chitosan blends, cross-linked with dialdehyde starch (DAS) and dialdehyde chitosan (DAC). DAS was commercially available, while DAC was obtained by one-step synthesis. Structure and physicochemical properties of the materials were characterized using Fourier transfer infrared spectroscopy with attenuated total reflectance device (FTIR-ATR), swelling behavior and water content measurements, porosity and density observations, scanning electron microscopy imaging (SEM), mechanical properties evaluation and thermogravimetric analysis. Metabolic activity with AlamarBlue assay and live/dead fluorescence staining were performed to evaluate the cytocompatibility of the obtained materials with MG-63 osteoblast-like cells. The results showed that the properties of the scaffolds based on silk fibroin, collagen and chitosan can be modified by chemical cross-linking with DAS and DAC. It was found that DAS and DAC have different influence on the properties of biopolymeric scaffolds. Materials cross-linked with DAS were characterized by higher swelling ability (~4000% for DAS cross-linked materials; ~2500% for DAC cross-linked materials), they had lower density (Coll/CTS/30SF scaffold cross-linked with DAS: 21.8 ± 2.4 g/cm3; cross-linked with DAC: 14.6 ± 0.7 g/cm3) and lower mechanical properties (maximum deformation for DAC cross-linked scaffolds was about 69%; for DAS cross-linked scaffolds it was in the range of 12.67 ± 1.51% and 19.83 ± 1.30%) in comparison to materials cross-linked with DAC. Additionally, scaffolds cross-linked with DAS exhibited higher biocompatibility than those cross-linked with DAC. However, the obtained results showed that both types of scaffolds can provide the support required in regenerative medicine and tissue engineering. The scaffolds presented in the present work can be potentially used in bone tissue engineering to facilitate healing of small bone defects.

scholarly journals 3D Printing of High Viscosity Reinforced Silicone Elastomers

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2239
Author(s):  
Nicholas Rodriguez ◽  
Samantha Ruelas ◽  
Jean-Baptiste Forien ◽  
Nikola Dudukovic ◽  
Josh DeOtte ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
New Technologies ◽  
Three Dimensional ◽  
High Viscosity ◽  
Layer By Layer ◽  
Silicone Elastomers ◽  
Uv Curable ◽  
Octet Truss ◽  
Tunable Mechanical Properties

Recent advances in additive manufacturing, specifically direct ink writing (DIW) and ink-jetting, have enabled the production of elastomeric silicone parts with deterministic control over the structure, shape, and mechanical properties. These new technologies offer rapid prototyping advantages and find applications in various fields, including biomedical devices, prosthetics, metamaterials, and soft robotics. Stereolithography (SLA) is a complementary approach with the ability to print with finer features and potentially higher throughput. However, all high-performance silicone elastomers are composites of polysiloxane networks reinforced with particulate filler, and consequently, silicone resins tend to have high viscosities (gel- or paste-like), which complicates or completely inhibits the layer-by-layer recoating process central to most SLA technologies. Herein, the design and build of a digital light projection SLA printer suitable for handling high-viscosity resins is demonstrated. Further, a series of UV-curable silicone resins with thiol-ene crosslinking and reinforced by a combination of fumed silica and MQ resins are also described. The resulting silicone elastomers are shown to have tunable mechanical properties, with 100–350% elongation and ultimate tensile strength from 1 to 2.5 MPa. Three-dimensional printed features of 0.4 mm were achieved, and complexity is demonstrated by octet-truss lattices that display negative stiffness.

Application of Microbial Polyesters-Polyhydroxyalkanoates as Tissue Engineering Materials

2005 ◽  
Vol 288-289 ◽  
pp. 437-440 ◽  
Author(s):  
Guo Qiang Chen ◽  
Qiong Wu ◽  
Ya Wu Wang ◽  
Zhong Zheng
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Surface Treatment ◽  
Surface Properties ◽  
Three Dimensional ◽  
Material Surface ◽  
New Class ◽  
Molecular Studies ◽  
Cartilage Cells ◽  
Engineering Materials

Poly(hydroxybutyrate-co-hydroxyhexanoate) (PHBHHx) has improved mechanical properties over the existing PHA and our results have shown that PHBHHx has better biocompatibility over polyhydroxybutyrate (PHB) and polylactic acid (PLA). Surface treatment with lipases dramatically changed the material surface properties and increased the biocompatibility of the PHBHHx. PHBHHx and its PHB blends had been used to make three dimensional structures and it has been found that cartilage, osteoblast, and fibroblasts all showed strong growth on the PHBHHx scaffolds. The growth was much better compared with PLA. The molecular studies also showed that mRNA encoding cartilages were strongly expressed when cartilage cells were grown on the PHBHHx. As PHBHHx has strong mechanical properties, easily processible and biodegradable, this material can be used to develop a new class of tissue engineering materials.

scholarly journals Biomimicry in Bio-Manufacturing: Developments in Melt Electrospinning Writing Technology Towards Hybrid Biomanufacturing

2019 ◽  
Vol 9 (17) ◽  
pp. 3540 ◽  
Author(s):  
Ferdows Afghah ◽  
Caner Dikyol ◽  
Mine Altunbek ◽  
Bahattin Koc
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Cell Attachment ◽  
Three Dimensional ◽  
Future Perspective ◽  
Melt Electrospinning ◽  
Wide Range ◽  
Challenges And Opportunities ◽  
Potential Applications ◽  
Homogeneous Cell

Melt electrospinning writing has been emerged as a promising technique in the field of tissue engineering, with the capability of fabricating controllable and highly ordered complex three-dimensional geometries from a wide range of polymers. This three-dimensional (3D) printing method can be used to fabricate scaffolds biomimicking extracellular matrix of replaced tissue with the required mechanical properties. However, controlled and homogeneous cell attachment on melt electrospun fibers is a challenge. The combination of melt electrospinning writing with other tissue engineering approaches, called hybrid biomanufacturing, has introduced new perspectives and increased its potential applications in tissue engineering. In this review, principles and key parameters, challenges, and opportunities of melt electrospinning writing, and particularly, recent approaches and materials in this field are introduced. Subsequently, hybrid biomanufacturing strategies are presented for improved biological and mechanical properties of the manufactured porous structures. An overview of the possible hybrid setups and applications, future perspective of hybrid processes, guidelines, and opportunities in different areas of tissue/organ engineering are also highlighted.

Combined Effects of Scaffold Material and Mechanical Stimulation on the Formation of Tissue Engineered Constructs Using Tendon and Ligament Progenitor Cells

2013 ◽  
Author(s):  
Andrew P. Breidenbach ◽  
Nathaniel A. Dyment ◽  
Yinhui Lu ◽  
Jason T. Shearn ◽  
David W. Rowe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Progenitor Cells ◽  
Three Dimensional ◽  
Musculoskeletal Injuries ◽  
Combined Effects ◽  
Joint Movement ◽  
Scaffold Material ◽  
Ligament Injuries ◽  
Promising Alternative

Tendon and ligament injuries account for one-third of all musculoskeletal injuries [1]. Collagen fibrils in these mechanosensitive tissues transmit forces to mobilize and stabilize joint movement. Donor tissues used to repair these tissues often lack the mechanical properties of the tissue they are replacing. One promising alternative using tissue engineering combines stem/progenitor cells in three-dimensional tissue engineered constructs (TECs).

scholarly journals Alginate/Gelatin Hydrogels Reinforced with TiO2 and β-TCP Fabricated by Microextrusion-based Printing for Tissue Regeneration

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 457 ◽  
Author(s):  
Rodrigo Urruela-Barrios ◽  
Erick Ramírez-Cedillo ◽  
A. Díaz de León ◽  
Alejandro Alvarez ◽  
Wendy Ortega-Lara
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Tissue Regeneration ◽  
Average Pore Size ◽  
Three Dimensional ◽  
Engineering Applications ◽  
Average Pore ◽  
Viscous Deformation ◽  
Freeze Dried ◽  
3D Printed

Three-dimensional (3D) printing technologies have become an attractive manufacturing process to fabricate scaffolds in tissue engineering. Recent research has focused on the fabrication of alginate complex shaped structures that closely mimic biological organs or tissues. Alginates can be effectively manufactured into porous three-dimensional networks for tissue engineering applications. However, the structure, mechanical properties, and shape fidelity of 3D-printed alginate hydrogels used for preparing tissue-engineered scaffolds is difficult to control. In this work, the use of alginate/gelatin hydrogels reinforced with TiO2 and β-tricalcium phosphate was studied to tailor the mechanical properties of 3D-printed hydrogels. The hydrogels reinforced with TiO2 and β-TCP showed enhanced mechanical properties up to 20 MPa of elastic modulus. Furthermore, the pores of the crosslinked printed structures were measured with an average pore size of 200 μm. Additionally, it was found that as more layers of the design were printed, there was an increase of the line width of the bottom layers due to its viscous deformation. Shrinkage of the design when the hydrogel is crosslinked and freeze dried was also measured and found to be up to 27% from the printed design. Overall, the proposed approach enabled fabrication of 3D-printed alginate scaffolds with adequate physical properties for tissue engineering applications.

Fabrication of a chitosan/bioglass three-dimensional porous scaffold for bone tissue engineering applications

2014 ◽  
Vol 2 (38) ◽  
pp. 6611-6618 ◽  
Author(s):  
Jun Yang ◽  
Teng Long ◽  
Nan-Fei He ◽  
Ya-Ping Guo ◽  
Zhen-An Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Porous Scaffold ◽  
Three Dimensional ◽  
Bone Defects ◽  
Engineering Applications

A chitosan/bioglass three-dimensional porous scaffold with excellent biocompatibility and mechanical properties has been developed for the treatment of bone defects.

Reversible physical crosslinking strategy with optimal temperature for 3D bioprinting of human chondrocyte-laden gelatin methacryloyl bioink

2018 ◽  
Vol 33 (5) ◽  
pp. 609-618 ◽  
Author(s):  
Yawei Gu ◽  
Lei Zhang ◽  
Xiaoyu Du ◽  
Ziwen Fan ◽  
Long Wang ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Three Dimensional ◽  
Optimal Temperature ◽  
Chondrocyte Viability ◽  
Human Chondrocyte ◽  
Tunable Mechanical Properties ◽  
Dimensional Cell ◽  
Physical Crosslinking ◽  
Better Than

Gelatin methacryloyl is a promising material in tissue engineering and has been widely studied in three-dimensional bioprinting. Although gelatin methacryloyl possesses excellent biocompatibility and tunable mechanical properties, its poor printability/processability has hindered its further applications. In this study, we report a reversible physical crosslinking strategy for precise deposition of human chondrocyte-laden gelatin methacryloyl bioink at low concentration without any sacrificial material by using extrusive three-dimensional bioprinting. The precise printing temperature was determined by the rheological properties of gelatin methacryloyl with temperature. Ten percent (w/v) gelatin methacryloyl was chosen as the printing formula due to highest biocompatibility in three-dimensional cell cultures in gelatin methacryloyl hydrogel disks. Primary human chondrocyte-laden 10% (w/v) gelatin methacryloyl was successfully printed without any construct deformation or collapse and was permanently crosslinked by ultraviolet light. The printed gelatin methacryloyl hydrogel constructs remained stable in long-term culture. Chondrocyte viability and proliferation that were printed under this optimal temperature were better than that of chondrocytes printed under lower temperatures and were similar to that of chondrocytes in the non-printed gelatin methacryloyl hydrogels. The results indicate that with this strategy, 10% (w/v) gelatin methacryloyl bioink presented excellent printability and printing resolution with high cell viability, which appears to be suitable for printing primary human chondrocytes in cartilage biofabrication and can be extensively applied in tissue engineering of other organs or in other biomedical fields.

Sign in / Sign up

Export Citation Format

Share Document