scholarly journals Alginate/Gelatin Hydrogels Reinforced with TiO2 and β-TCP Fabricated by Microextrusion-based Printing for Tissue Regeneration

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 457 ◽  
Author(s):  
Rodrigo Urruela-Barrios ◽  
Erick Ramírez-Cedillo ◽  
A. Díaz de León ◽  
Alejandro Alvarez ◽  
Wendy Ortega-Lara
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Tissue Regeneration ◽  
Average Pore Size ◽  
Three Dimensional ◽  
Engineering Applications ◽  
Average Pore ◽  
Viscous Deformation ◽  
Freeze Dried ◽  
3D Printed

Three-dimensional (3D) printing technologies have become an attractive manufacturing process to fabricate scaffolds in tissue engineering. Recent research has focused on the fabrication of alginate complex shaped structures that closely mimic biological organs or tissues. Alginates can be effectively manufactured into porous three-dimensional networks for tissue engineering applications. However, the structure, mechanical properties, and shape fidelity of 3D-printed alginate hydrogels used for preparing tissue-engineered scaffolds is difficult to control. In this work, the use of alginate/gelatin hydrogels reinforced with TiO2 and β-tricalcium phosphate was studied to tailor the mechanical properties of 3D-printed hydrogels. The hydrogels reinforced with TiO2 and β-TCP showed enhanced mechanical properties up to 20 MPa of elastic modulus. Furthermore, the pores of the crosslinked printed structures were measured with an average pore size of 200 μm. Additionally, it was found that as more layers of the design were printed, there was an increase of the line width of the bottom layers due to its viscous deformation. Shrinkage of the design when the hydrogel is crosslinked and freeze dried was also measured and found to be up to 27% from the printed design. Overall, the proposed approach enabled fabrication of 3D-printed alginate scaffolds with adequate physical properties for tissue engineering applications.

Fabrication of a chitosan/bioglass three-dimensional porous scaffold for bone tissue engineering applications

2014 ◽  
Vol 2 (38) ◽  
pp. 6611-6618 ◽  
Author(s):  
Jun Yang ◽  
Teng Long ◽  
Nan-Fei He ◽  
Ya-Ping Guo ◽  
Zhen-An Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Porous Scaffold ◽  
Three Dimensional ◽  
Bone Defects ◽  
Engineering Applications

A chitosan/bioglass three-dimensional porous scaffold with excellent biocompatibility and mechanical properties has been developed for the treatment of bone defects.

scholarly journals Highly flexible silica/chitosan hybrid scaffolds with oriented pores for tissue regeneration

2015 ◽  
Vol 3 (38) ◽  
pp. 7560-7576 ◽  
Author(s):  
Daming Wang ◽  
Frederik Romer ◽  
Louise Connell ◽  
Claudia Walter ◽  
Eduardo Saiz ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Tissue Regeneration ◽  
Sol Gel ◽  
Engineering Applications ◽  
Hybrid Scaffolds ◽  
Unique Potential ◽  
Inorganic Components

Inorganic/organic sol–gel hybrids have nanoscale co-networks of organic and inorganic components that give them the unique potential of tailored mechanical properties and controlled biodegradation in tissue engineering applications.

scholarly journals Pectin-Based Scaffolds for Tissue Engineering Applications

2021 ◽  
Author(s):  
Anna Lapomarda ◽  
Aurora De Acutis ◽  
Carmelo De Maria ◽  
Giovanni Vozzi
Keyword(s):  
Tissue Engineering ◽  
Wound Healing ◽  
Tissue Regeneration ◽  
Three Dimensional ◽  
Tissue Formation ◽  
Fabrication Technology ◽  
Engineering Applications ◽  
Structural Support ◽  
Interdisciplinary Field ◽  
Alternative Approaches

Tissue engineering (TE) is an interdisciplinary field that was introduced from the necessity of finding alternative approaches to transplantation for the treatment of damaged and diseased organs or tissues. Unlike the conventional procedures, TE aims at inducing the regeneration of injured tissues through the implantation of customized and functional engineered tissues, built on the so-called ‘scaffolds’. These provide structural support to cells and regulate the process of new tissue formation. The properties of the scaffold are essentials, and they can be controlled by varying the biomaterial formulation and the fabrication technology used to its production. Pectin is emerging as an alternative biomaterial to non-degradable and high-cost petroleum-based biopolymers commonly used in this field. It shows several promising properties including biocompatibility, biodegradability, non-toxicity and gelling capability. Pectin-based formulations can be processed through different fabrication approaches into bidimensional and three-dimensional scaffolds. This chapter aims at highlighting the potentiality in using pectin as biomaterial in the field of tissue engineering. The most representative applications of pectin in preparing scaffolds for wound healing and tissue regeneration are discussed.

scholarly journals Combining Materials Obtained by 3D-Printing and Electrospinning from Commercial Polylactide Filament to Produce Biocompatible Composites

Polymers ◽  
2021 ◽  
Vol 13 (21) ◽  
pp. 3806
Author(s):  
Pablo Romero-Araya ◽  
Victor Pino ◽  
Ariel Nenen ◽  
Verena Cárdenas ◽  
Francisca Pavicic ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
3D Printing ◽  
Three Dimensional ◽  
Fibrillar Structure ◽  
3D Print ◽  
3T3 Fibroblasts ◽  
Custom Made ◽  
3D Printers ◽  
3D Printed

The design of scaffolds to reach similar three-dimensional structures mimicking the natural and fibrous environment of some cells is a challenge for tissue engineering, and 3D-printing and electrospinning highlights from other techniques in the production of scaffolds. The former is a well-known additive manufacturing technique devoted to the production of custom-made structures with mechanical properties similar to tissues and bones found in the human body, but lacks the resolution to produce small and interconnected structures. The latter is a well-studied technique to produce materials possessing a fibrillar structure, having the advantage of producing materials with tuned composition compared with a 3D-print. Taking the advantage that commercial 3D-printers work with polylactide (PLA) based filaments, a biocompatible and biodegradable polymer, in this work we produce PLA-based composites by blending materials obtained by 3D-printing and electrospinning. Porous PLA fibers have been obtained by the electrospinning of recovered PLA from 3D-printer filaments, tuning the mechanical properties by blending PLA with small amounts of polyethylene glycol and hydroxyapatite. A composite has been obtained by blending two layers of 3D-printed pieces with a central mat of PLA fibers. The composite presented a reduced storage modulus as compared with a single 3D-print piece and possessing similar mechanical properties to bone tissues. Furthermore, the biocompatibility of the composites is assessed by a simulated body fluid assay and by culturing composites with 3T3 fibroblasts. We observed that all these composites induce the growing and attaching of fibroblast over the surface of a 3D-printed layer and in the fibrous layer, showing the potential of commercial 3D-printers and filaments to produce scaffolds to be used in bone tissue engineering.

scholarly journals Is Dialdehyde Chitosan a Good Substance to Modify Physicochemical Properties of Biopolymeric Materials?

2021 ◽  
Vol 22 (7) ◽  
pp. 3391
Author(s):  
Sylwia Grabska-Zielińska ◽  
Alina Sionkowska ◽  
Ewa Olewnik-Kruszkowska ◽  
Katarzyna Reczyńska ◽  
Elżbieta Pamuła
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Physicochemical Properties ◽  
Silk Fibroin ◽  
Three Dimensional ◽  
Microscopy Imaging ◽  
Maximum Deformation ◽  
One Step ◽  
Chitosan Blends ◽  
Fourier Transfer Infrared Spectroscopy

The aim of this work was to compare physicochemical properties of three dimensional scaffolds based on silk fibroin, collagen and chitosan blends, cross-linked with dialdehyde starch (DAS) and dialdehyde chitosan (DAC). DAS was commercially available, while DAC was obtained by one-step synthesis. Structure and physicochemical properties of the materials were characterized using Fourier transfer infrared spectroscopy with attenuated total reflectance device (FTIR-ATR), swelling behavior and water content measurements, porosity and density observations, scanning electron microscopy imaging (SEM), mechanical properties evaluation and thermogravimetric analysis. Metabolic activity with AlamarBlue assay and live/dead fluorescence staining were performed to evaluate the cytocompatibility of the obtained materials with MG-63 osteoblast-like cells. The results showed that the properties of the scaffolds based on silk fibroin, collagen and chitosan can be modified by chemical cross-linking with DAS and DAC. It was found that DAS and DAC have different influence on the properties of biopolymeric scaffolds. Materials cross-linked with DAS were characterized by higher swelling ability (~4000% for DAS cross-linked materials; ~2500% for DAC cross-linked materials), they had lower density (Coll/CTS/30SF scaffold cross-linked with DAS: 21.8 ± 2.4 g/cm3; cross-linked with DAC: 14.6 ± 0.7 g/cm3) and lower mechanical properties (maximum deformation for DAC cross-linked scaffolds was about 69%; for DAS cross-linked scaffolds it was in the range of 12.67 ± 1.51% and 19.83 ± 1.30%) in comparison to materials cross-linked with DAC. Additionally, scaffolds cross-linked with DAS exhibited higher biocompatibility than those cross-linked with DAC. However, the obtained results showed that both types of scaffolds can provide the support required in regenerative medicine and tissue engineering. The scaffolds presented in the present work can be potentially used in bone tissue engineering to facilitate healing of small bone defects.

Preparation and Characterization of Chitosan-Based Scaffolds for Biomedical Applications

2006 ◽  
Vol 514-516 ◽  
pp. 1005-1009 ◽  
Author(s):  
José V. Araújo ◽  
J.A. Lopes da Silva ◽  
Margarida M. Almeida ◽  
Maria Elisabete V. Costa
Keyword(s):  
Biomedical Applications ◽  
Freeze Drying ◽  
Average Pore Size ◽  
Composite Scaffolds ◽  
Average Pore ◽  
Chitosan Matrix ◽  
Freeze Dried ◽  
Porous Chitosan ◽  
Interconnected Structure

Porous chitosan/brushite composite scaffolds were prepared by a freeze-drying technique, starting from brushite suspensions in chitosan solutions. The obtained scaffolds showed a regular macroporous and interconnected structure with brushite particles uniformly distributed in the chitosan matrix. The variation of the brushite concentration affected the microstructure of the final freeze-dried scaffold, in particular, its porosity and its average pore size. The yield strengths of the composite scaffolds could also be improved by the increase of the brushite content.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Three-Dimensional Printable Hydrogel Using a Hyaluronic Acid/Sodium Alginate Bio-Ink

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 794 ◽  
Author(s):  
Su Jeong Lee ◽  
Ji Min Seok ◽  
Jun Hee Lee ◽  
Jaejong Lee ◽  
Wan Doo Kim ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Hyaluronic Acid ◽  
Sodium Alginate ◽  
Three Dimensional ◽  
Fibroblast Cell ◽  
Chemical Crosslinking ◽  
Fibroblast Cell Line ◽  
Engineering Applications ◽  
Encapsulated Cells ◽  
Crosslinking Agents

Bio-ink properties have been extensively studied for use in the three-dimensional (3D) bio-printing process for tissue engineering applications. In this study, we developed a method to synthesize bio-ink using hyaluronic acid (HA) and sodium alginate (SA) without employing the chemical crosslinking agents of HA to 30% (w/v). Furthermore, we evaluated the properties of the obtained bio-inks to gauge their suitability in bio-printing, primarily focusing on their viscosity, printability, and shrinkage properties. Furthermore, the bio-ink encapsulating the cells (NIH3T3 fibroblast cell line) was characterized using a live/dead assay and WST-1 to assess the biocompatibility. It was inferred from the results that the blended hydrogel was successfully printed for all groups with viscosities of 883 Pa∙s (HA, 0% w/v), 1211 Pa∙s (HA, 10% w/v), and 1525 Pa∙s, (HA, 30% w/v) at a 0.1 s−1 shear rate. Their structures exhibited no significant shrinkage after CaCl2 crosslinking and maintained their integrity during the culture periods. The relative proliferation rate of the encapsulated cells in the HA/SA blended bio-ink was 70% higher than the SA-only bio-ink after the fourth day. These results suggest that the 3D printable HA/SA hydrogel could be used as the bio-ink for tissue engineering applications.

scholarly journals Three-Dimensional Printing of Hydroxyapatite Composites for Biomedical Application

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 353
Author(s):  
Yanting Han ◽  
Qianqian Wei ◽  
Pengbo Chang ◽  
Kehui Hu ◽  
Oseweuba Valentine Okoro ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Biomedical Application ◽  
Three Dimensional ◽  
Antibacterial Properties ◽  
Natural Polymers ◽  
Three Dimensional Printing ◽  
3D Printed ◽  
Dental Applications ◽  
Hard Tissue Engineering

Hydroxyapatite (HA) and HA-based nanocomposites have been recognized as ideal biomaterials in hard tissue engineering because of their compositional similarity to bioapatite. However, the traditional HA-based nanocomposites fabrication techniques still limit the utilization of HA in bone, cartilage, dental, applications, and other fields. In recent years, three-dimensional (3D) printing has been shown to provide a fast, precise, controllable, and scalable fabrication approach for the synthesis of HA-based scaffolds. This review therefore explores available 3D printing technologies for the preparation of porous HA-based nanocomposites. In the present review, different 3D printed HA-based scaffolds composited with natural polymers and/or synthetic polymers are discussed. Furthermore, the desired properties of HA-based composites via 3D printing such as porosity, mechanical properties, biodegradability, and antibacterial properties are extensively explored. Lastly, the applications and the next generation of HA-based nanocomposites for tissue engineering are discussed.

Sign in / Sign up

Export Citation Format

Share Document