scholarly journals Sessile droplets containing carbon nanotubes: a study of evaporation dynamics and CNT alignment for printed electronics

Nanoscale ◽  
2019 ◽  
Vol 11 (22) ◽  
pp. 10603-10614 ◽  
Author(s):  
Guo Liang Goh ◽  
Nitipon Saengchairat ◽  
Shweta Agarwala ◽  
Wai Yee Yeong ◽  
Tuan Tran

A study of evaporation dynamics of the CNT suspensions and CNT alignment via sessile drop experiments on a flexible substrate.

Molecules ◽  
2021 ◽  
Vol 26 (10) ◽  
pp. 2908
Author(s):  
Kazuo Umemura ◽  
Ryo Hamano ◽  
Hiroaki Komatsu ◽  
Takashi Ikuno ◽  
Eko Siswoyo

Solubilization of carbon nanotubes (CNTs) is a fundamental technique for the use of CNTs and their conjugates as nanodevices and nanobiodevices. In this work, we demonstrate the preparation of CNT suspensions with “green” detergents made from coconuts and bamboo as fundamental research in CNT nanotechnology. Single-walled CNTs (SWNTs) with a few carboxylic acid groups (3–5%) and pristine multi-walled CNTs (MWNTs) were mixed in each detergent solution and sonicated with a bath-type sonicator. The prepared suspensions were characterized using absorbance spectroscopy, scanning electron microscopy, and Raman spectroscopy. Among the eight combinations of CNTs and detergents (two types of CNTs and four detergents, including sodium dodecyl sulfate (SDS) as the standard), SWNTs/MWNTs were well dispersed in all combinations except the combination of the MWNTs and the bamboo detergent. The stability of the suspensions prepared with coconut detergents was better than that prepared with SDS. Because the efficiency of the bamboo detergents against the MWNTs differed significantly from that against the SWNTs, the natural detergent might be useful for separating CNTs. Our results revealed that the use of the “green” detergents had the advantage of dispersing CNTs as well as SDS.


Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 713 ◽  
Author(s):  
Romana Daňová ◽  
Robert Olejnik ◽  
Petr Slobodian ◽  
Jiri Matyas

Wearable electronic sensor was prepared on a light and flexible substrate. The breathing sensor has a broad assumption and great potential for portable devices in wearable technology. In the present work, the application of a flexible thermoplastic polyurethane/multiwalled carbon nanotubes (TPU/MWCNTs) strain sensor was demonstrated. This composite was prepared by a novel technique using a thermoplastic filtering membrane based on electrospinning technology. Aqueous dispersion of MWCNTs was filtered through membrane, dried and then welded directly on a T-shirt and encapsulated by a thin silicone layer. The sensing layer was also equipped by electrodes. A polymer composite sensor is capable of detecting a deformation by changing its electrical resistance. A T-shirt was capable of analyzing a type, frequency and intensity of human breathing. The sensitivity to the applied strain of the sensor was improved by the oxidation of MWCNTs by potassium permanganate (KMnO4) and also by subsequent application of the prestrain.


Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 245 ◽  
Author(s):  
Sang Lee ◽  
Sangyoon Lee

Although printed electronics technology has been recently employed in the production of various devices, its use for the fabrication of electronic devices with air-gap structures remains challenging. This paper presents a productive roll-to-roll printed electronics method for the fabrication of capacitive touch sensors with air-gap structures. Each layer of the sensor was fabricated by printing or coating. The bottom electrode, and the dielectric and sacrificial layers were roll-to-roll slot-die coated on a flexible substrate. The top electrode was formed by roll-to-roll gravure printing, while the structural layer was formed by spin-coating. In particular, the sacrificial layer was coated with polyvinyl alcohol (PVA) and removed in water to form an air-gap. The successful formation of the air-gap was verified by field emission scanning electron microscopy (FE-SEM). Electrical characteristics of the air-gap touch sensor samples were analyzed in terms of sensitivity, hysteresis, and repeatability. Experimental results showed that the proposed method can be suitable for the fabrication of air-gap sensors by using the roll-to-roll printed electronics technology.


Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1879
Author(s):  
Aniello Falco ◽  
Francisco J. Romero ◽  
Florin C. Loghin ◽  
Alina Lyuleeva ◽  
Markus Becherer ◽  
...  

This work demonstrates a cost-effective manufacturing method of flexible and fully printed microheaters, using carbon nanotubes (CNTs) as the heating element. Two different structures with different number of CNT layers have been characterized in detail. The benchmarking has been carried out in terms of maximum operating temperature, as well as nominal resistance and input power for different applied voltages. Their performances have been compared with previous reports for similar devices, fabricated with other technologies. The results have shown that the heaters presented can achieve high temperatures in a small area at lower voltages and lower input power. In particular, the fully printed heaters fabricated on a flexible substrate covering an area of 3.2 mm2 and operating at 9.5 V exhibit a maximum temperature point above 70 °C with a power consumption below 200 mW. Therefore, we have demonstrated that this technology paves the way for a cost-effective large-scale fabrication of flexible microheaters aimed to be integrated in flexible sensors.


2009 ◽  
Vol 2 (1) ◽  
pp. 75-78 ◽  
Author(s):  
Shinichi Nishi ◽  
Kazuo Asano ◽  
Daisuke Ishibashi ◽  
Akiko Kitami ◽  
Kumiko Furuno

2012 ◽  
Vol 96 ◽  
pp. 71-75 ◽  
Author(s):  
Da Zhao ◽  
Tao Liu ◽  
Jin Gyu Park ◽  
Mei Zhang ◽  
Jen-Ming Chen ◽  
...  

2013 ◽  
Vol 1505 ◽  
Author(s):  
Pingye Xu ◽  
Michael C. Hamilton

ABSTRACTCarbon nanotubes patterns of micron-level resolution have been achieved using inkjet printing of DNA and SDS assisted CNT dispersions. DNA/CNT film has a significantly higher resistance compared to SDS/CNT film. Taking advantage of the porous nature of printed SDS/CNT film after SDS removal, indium can be electroplated to fill the CNT network and form a CNT/In composite. The CNT/In composite was used as interconnect material. Reworkability and RF performance of In-plated CNT bump structures are studied and the results are presented.


Sign in / Sign up

Export Citation Format

Share Document