Low-temperature sol–gel synthesis of crystalline materials

RSC Advances ◽  
2014 ◽  
Vol 4 (86) ◽  
pp. 45903-45919 ◽  
Author(s):  
Alexandr V. Vinogradov ◽  
Vladimir V. Vinogradov

Sol–gel chemistry has opened a new era of modern materials science by enabling the production of ceramic materials at near-room temperature.

ChemInform ◽  
2014 ◽  
Vol 46 (2) ◽  
pp. no-no
Author(s):  
Alexandr V. Vinogradov ◽  
Vladimir V. Vinogradov

2003 ◽  
Vol 807 ◽  
Author(s):  
Evgeniy B. Anderson ◽  
Boris E. Burakov

ABSTRACTSince 1990, the Laboratory of Applied Mineralogy and Radiogeochemistry of the V.G. Khlopin Radium Institute (KRI) has been developing several different types of crystalline host-phases acceptable for the economically feasible and environmentally safe immobilization of actinide wastes. We proposed that ceramics that are based on host phases similar to naturally occurring accessory minerals including zircon, (Zr,Hf,…)SiO4; hafnon, (Hf,Zr,…)SiO4; baddeleyite (monoclinic zirconia), (Zr,Hf,…)O2; tazheranite (cubic zirconia), (Zr,Hf,Ca,Ti,…)O2; garnet, (Ca,Fe,Gd,…)3(Al,Fe,Si,…)5O12; perovskite, (Ca,Gd,…)(Al,Fe,Ti,…)O3, and monazite, (La,Ce,…)PO4, are the most efficient materials for actinide immobilization in deep geological formations. Solid solution of Pu in zirconia, (Zr,Pu)O2, could be used as a ceramic nuclear fuel that is competitive with mixed oxide fuel (MOX). To date, the following crystalline materials doped with 239Pu, 238Pu and 243Am have been successfully synthesized and studied at KRI: zircon; hafnon; cubic and tetragonal zirconia; monazite; aluminate garnet and perovskite. The maximum actinide loading was (in wt.% el.): 239Pu -37; 238Pu-10; 243Am-23. All Pu-Am-doped samples were made in air atmosphere under glove boxes conditions. Polycrystalline (ceramic) materials were made by sintering or melting of sol-gel, co-precipitated hydroxides, oxalates and phosphates or ground oxide precursors; single crystals were grown by a flux method. It was demonstrated that all ceramic samples obtained are characterized by high chemical durability and typical normalized actinide losses in deionized water at 90°C do not exceed 10−2–10−3 g/m2 (without correction for ceramic porosity). However, investigation of long-term behavior of ceramic waste forms requires taking into account the results of accelerated radiation damage study and modeling of ceramic alteration by underground solutions. The principal features of Pu-Am-doped samples obtained so far at KRI and their synthesis conditions are discussed.


2014 ◽  
Vol 979 ◽  
pp. 39-42
Author(s):  
Saran Kalasina ◽  
Taweechai Amornsakchai ◽  
Udom Asawapirom

Solvolytic sol-gel synthesis was applied for the low temperature production of photoelectrode for dye-sensitized solar cell (DSSC). In this study, commercial TiO2 standard (Degussa P25) was used as the main component in the preparation of photoelectrode film. Addition of TiO2 gel prepared from a solvolytic sol-gel method reduced cracking in the dry film while still maintains porosity. Further modification by simply adding hydrofluoric acid (HF) and ammonia (NH3) increase porosity and improve interconnection between fluorine doped tin oxide (FTO) layer on the substrate and the coated TiO2 layer even under low temperature baking condition (<150°C). The modified TiO2 electrode showed significantly better electrical and electrochemical properties. Furthermore, the DSSC cell with modified TiO2 film also showed higher cell efficiency when compared with the controlled cell that used only Degussa P25.


Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 911 ◽  
Author(s):  
Olga Sacco ◽  
Diana Sannino ◽  
Mariantonietta Matarangolo ◽  
Vincenzo Vaiano

In this work, the influence of simple acids in the room temperature sol-gel synthesis of TiO2 was investigated and the efficiency of prepared photocatalysts was evaluated in the removal of caffeine. To improve the photoactivity of TiO2, vanadium-doped TiO2 (VTiO2) samples were obtained starting from different amount of vanadyl sulphate as a dopant source. The samples were centrifuged, washed and finally dried at room temperature, and no calcination step was carried out. The prepared photocatalysts were characterized by different techniques (X-ray powder diffraction (XRD), specific surface area (SSA), ultraviolet-visible diffuse reflectance spectra (UV-vis DRS) and Raman). VTiO2 photocatalysts were tested in the photocatalytic removal of aqueous solutions containing caffeine. The photocatalytic tests were carried out in a recirculating batch cylindrical photoreactor irradiated by a UV LEDs strip (nominal power of 12 W and wavelength emission peak at about 365 nm) surrounding the external surface of the reactor. The optimized VTiO2 photocatalyst was able to reach a caffeine degradation of about 96% after 360 min of UV light irradiation with a total organic carbon (TOC) removal of 72%.


2021 ◽  
Vol 111 ◽  
pp. 106458
Author(s):  
Ramunas Diliautas ◽  
Aldona Beganskiene ◽  
Dovydas Karoblis ◽  
Kestutis Mazeika ◽  
Dalis Baltrunas ◽  
...  

ChemInform ◽  
1990 ◽  
Vol 21 (42) ◽  
Author(s):  
D. K. AGRAWAL ◽  
J. H. ADAIR

RSC Advances ◽  
2014 ◽  
Vol 4 (87) ◽  
pp. 46762-46770 ◽  
Author(s):  
Mohamed Karmaoui ◽  
David M. Tobaldi ◽  
Andrijana Sever Skapin Andrijana Sever Skapin ◽  
Robert C. Pullar ◽  
Maria P. Seabra ◽  
...  

A novel, facile method based on a non-aqueous sol–gel solvothermal process has been developed to synthesise spherical TiO2 nanoparticles (NPs) in one pot.


2014 ◽  
Vol 2 (40) ◽  
pp. 8607-8613 ◽  
Author(s):  
Benjamin Ritter ◽  
Thoralf Krahl ◽  
Knut Rurack ◽  
Erhard Kemnitz

Easy upscaleable one-pot synthesis method at room temperature for ultra small sized Eu3+- and Tb3+-doped CaF2 nanoparticles.


Sign in / Sign up

Export Citation Format

Share Document