The Problem of High Temperature Alloys for Gas Turbines

1948 ◽  
Vol 52 (445) ◽  
pp. 1-26
Author(s):  
William T. Griffiths
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
High Temperatures ◽  
Gas Turbines ◽  
High Speed ◽  
Mechanical Equipment ◽  
Aircraft Engines ◽  
Efficient Operation ◽  
High Temperature Alloys

It is now a matter of history that the development of an efficient gas turbine for use in aircraft engines had to await the availability of materials with the properties which would give an adequate life under the conditions which have to be imposed for efficient and economic service. These conditions are, of their type, more severe than any so far imposed on materials in other mechanical equipment. For efficient operation the gases employed in the turbine must be at a high temperature and the flow of gas passing through must be large. In aircraft engines also, the turbine must operate at high speed, with the resulting accompaniment of high stresses. It was to the metallurgist that the engineer naturally turned first for materials to meet these conditions of high temperatures and high stresses and, although some attention has been given to non-metallic substances, the problem still remains essentially a metallurgical one.

An Improved Nickel Based MIMS Thermocouple for High Temperature Gas Turbine Applications

2012 ◽  
Author(s):  
Michele Scervini ◽  
Catherine Rae
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
High Temperatures ◽  
Gas Turbines ◽  
Material Science ◽  
University Of Cambridge ◽  
Type K ◽  
Metallurgical Analysis ◽  
The University ◽  
High Temperature Gas

A new Nickel based thermocouple for high temperature applications in gas turbines has been devised at the Department of Material Science and Metallurgy of the University of Cambridge. This paper describes the new features of the thermocouple, the drift tests on the first prototype and compares the behaviour of the new sensor with conventional mineral insulated metal sheathed Type K thermocouples: the new thermocouple has a significant improvement in terms of drift and temperature capabilities. Metallurgical analysis has been undertaken on selected sections of the thermocouples exposed at high temperatures which rationalises the reduced drift of the new sensor. A second prototype will be tested in follow-on research, from which further improvements in drift and temperature capabilities are expected.

An Improved Nickel Based MIMS Thermocouple for High Temperature Gas Turbine Applications

2013 ◽  
Vol 135 (9) ◽  
Author(s):  
Michele Scervini ◽  
Catherine Rae
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
High Temperatures ◽  
Gas Turbines ◽  
Material Science ◽  
University Of Cambridge ◽  
Type K ◽  
Metallurgical Analysis ◽  
The University ◽  
High Temperature Gas

A new nickel based thermocouple for high temperature applications in gas turbines has been devised at the Department of Material Science and Metallurgy of the University of Cambridge. This paper describes the new features of the thermocouple, the drift tests on the first prototype, and compares the behavior of the new sensor with conventional mineral insulated metal sheathed Type K thermocouples: the new thermocouple has a significant improvement in terms of drift and temperature capabilities. Metallurgical analysis has been undertaken on selected sections of the thermocouples exposed at high temperatures, which rationalizes the reduced drift of the new sensor. A second prototype will be tested in subsequent research, from which further improvements in drift and temperature capabilities are expected.

Influence of Carrier Air Preheating on Autoignition of Inline-Injected Hydrogen-Nitrogen Mixtures in Vitiated Air of High Temperature

2017 ◽  
Author(s):  
Christoph A. Schmalhofer ◽  
Peter Griebel ◽  
Manfred Aigner
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Spatial Development ◽  
Design Guidelines ◽  
Operating Conditions ◽  
High Speed Imaging ◽  
Temporal And Spatial ◽  
Fuel Mixtures

Gas turbines will play a significant role in future power generation systems because they provide peak capacity due to their fast start-up capability and high operational flexibility. However, in order to meet the COP 21 goals, de-carbonization of as turbine fuels is required. Compared to natural gas operation, autoignition and flashback risks in gas turbines operated on hydrogen-rich fuels are higher which has to be taken into account for a proper gas turbine design. From investigations of these phenomena at relevant operating conditions with appropriate measurement techniques, e.g. high-speed imaging, the understanding of the non-stationary processes occurring during autoignition can be improved and design guidelines for a safe and reliable gas turbine operation can be derived. The present study investigates the influences of elevated carrier-air preheating temperatures and hydrogen fuel volume fractions on autoignition at hot gas temperatures higher than 1100 K and pressures of 15 bar. An in-line co-flow injector is used to inject the hydrogen-nitrogen fuel mixtures. The formation, temporal and spatial development of autoignition kernels at high-temperature vitiated air conditions, e.g. relevant to reheat combustor operation, are studied. The experiments were conducted in an optically accessible mixing section of a generic reheat combustor. The hydrogen-nitrogen fuel mixtures of up to 70 vol. % hydrogen are injected in-line into the mixing section along with the carrier-air which was preheated to temperatures between 303 K and 703 K. High-speed imaging was used to detect the autoignition kernels and their temporal and spatial development from luminescence signals. Particle Image Velocimetry measurements were conducted to obtain the velocity distribution in the mixing section at autoignition conditions. The influences of vitiated air temperatures and carrier preheating temperatures on autoignition and flame stabilisation limits are shown, alongside the spatial distribution of different types of autoignition kernels, developing at different stages of the autoignition process. The development of autoignition kernels could be linked to the shear layer development derived from global experimental conditions.

scholarly journals Wall Temperature Measurements in Gas Turbine Combustors With Thermographic Phosphors

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Patrick Nau ◽  
Zhiyao Yin ◽  
Oliver Lammel ◽  
Wolfgang Meier
Keyword(s):  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Bluff Body ◽  
Temperature Measurements ◽  
Transient Temperature ◽  
High Time Resolution ◽  
Ceramic Surface ◽  
Precessing Vortex Core

Phosphor thermometry has been developed for wall temperature measurements in gas turbines and gas turbine model combustors. An array of phosphors has been examined in detail for spatially and temporally resolved surface temperature measurements. Two examples are provided, one at high pressure (8 bar) and high temperature and one at atmospheric pressure with high time resolution. To study the feasibility of this technique for full-scale gas turbine applications, a high momentum confined jet combustor at 8 bar was used. Successful measurements up to 1700 K on a ceramic surface are shown with good accuracy. In the same combustor, temperatures on the combustor quartz walls were measured, which can be used as boundary conditions for numerical simulations. An atmospheric swirl-stabilized flame was used to study transient temperature changes on the bluff body. For this purpose, a high-speed setup (1 kHz) was used to measure the wall temperatures at an operating condition where the flame switches between being attached (M-flame) and being lifted (V-flame) (bistable). The influence of a precessing vortex core (PVC) present during M-flame periods is identified on the bluff body tip, but not at positions further inside the nozzle.

Development and Fabrication of Silicon Nitride Components for Ceramic Gas Turbine

1997 ◽  
Author(s):  
Keisuke Makino ◽  
Ken-Ichi Mizuno ◽  
Toru Shimamori
Keyword(s):  
High Temperature ◽  
Silicon Nitride ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Blades ◽  
High Strength ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Spark Plug ◽  
Power Turbine

NGK Spark Plug Co., Ltd. has been developing various silicon nitride materials, and the technology for fabricating components for ceramic gas turbines (CGT) using theses materials. We are supplying silicon nitride material components for the project to develop 300 kW class CGT for co-generation in Japan. EC-152 was developed for components that require high strength at high temperature, such as turbine blades and turbine nozzles. In order to adapt the increasing of the turbine inlet temperature (TIT) up to 1,350 °C in accordance with the project goals, we developed two silicon nitride materials with further unproved properties: ST-1 and ST-2. ST-1 has a higher strength than EC-152 and is suitable for first stage turbine blades and power turbine blades. ST-2 has higher oxidation resistance than EC-152 and is suitable for power turbine nozzles. In this paper, we report on the properties of these materials, and present the results of evaluations of these materials when they are actually used for CGT components such as first stage turbine blades and power turbine nozzles.

Boundary Layer Flashback Limits of Hydrogen-Methane-Air Flames in a Generic Swirl Burner at Gas Turbine Relevant Conditions

2020 ◽  
Author(s):  
Dominik Ebi ◽  
Peter Jansohn
Keyword(s):  
Boundary Layer ◽  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Cooling System ◽  
Atmospheric Conditions ◽  
Preheat Temperature ◽  
Swirl Burner ◽  
Wide Range

Abstract Operating stationary gas turbines on hydrogen-rich fuels offers a pathway to significantly reduce greenhouse gas emissions in the power generation sector. A key challenge in the design of lean-premixed burners, which are flexible in terms of the amount of hydrogen in the fuel across a wide range and still adhere to the required emissions levels, is to prevent flame flashback. However, systematic investigations on flashback at gas turbine relevant conditions to support combustor development are sparse. The current work addresses the need for an improved understanding with an experimental study on boundary layer flashback in a generic swirl burner up to 7.5 bar and 300° C preheat temperature. Methane-hydrogen-air flames with 50 to 85% hydrogen by volume were investigated. High-speed imaging was applied to reveal the flame propagation pathway during flashback events. Flashback limits are reported in terms of the equivalence ratio for a given pressure, preheat temperature, bulk flow velocity and hydrogen content. The wall temperature of the center body along which the flame propagated during flashback events has been controlled by an oil heating/cooling system. This way, the effect any of the control parameters, e.g. pressure, had on the flashback limit was de-coupled from the otherwise inherently associated change in heat load on the wall and thus change in wall temperature. The results show that the preheat temperature has a weaker effect on the flashback propensity than expected. Increasing the pressure from atmospheric conditions to 2.5 bar strongly increases the flashback risk, but hardly affects the flashback limit beyond 2.5 bar.

Problems in the Mechanical Design of Gas Turbines

1947 ◽  
Vol 14 (2) ◽  
pp. A99-A102
Author(s):  
Ronald B. Smith
Keyword(s):  
Gas Turbine ◽  
High Temperatures ◽  
Gas Turbines ◽  
Mechanical Design

Abstract High temperatures involved in the operation of the gas turbine have introduced many new problems in the properties of the metals with which the designer has to work. This paper outlines some of these and offers a line of approach taken successfully by the author’s company in solving them.

The Effect of Transient Fuel Staging on Self-Excited Instabilities in a Multi-Nozzle Model Gas Turbine Combustor

2017 ◽  
Author(s):  
Wyatt Culler ◽  
Janith Samarasinghe ◽  
Bryan D. Quay ◽  
Domenic A. Santavicca ◽  
Jacqueline O’Connor
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Equivalence Ratio ◽  
Growth Time ◽  
Stable Operation ◽  
Time Constants ◽  
Decay Times ◽  
Fuel Staging ◽  
Passive Techniques

Combustion instability in gas turbines can be mitigated using active techniques or passive techniques, but passive techniques are almost exclusively used in industrial settings. While fuel staging, a common passive technique, is effective in reducing the amplitude of self-excited instabilities in gas turbine combustors at steady-state conditions, the effect of transients in fuel staging on self-excited instabilities is not well understood. This paper examines the effect of fuel staging transients on a laboratory-scale five-nozzle can combustor undergoing self-excited instabilities. The five nozzles are arranged in a four-around-one configuration and fuel staging is accomplished by increasing the center nozzle equivalence ratio. When the global equivalence ratio is φ = 0.70 and all nozzles are fueled equally, the combustor undergoes self-excited oscillations. These oscillations are suppressed when the center nozzle equivalence ratio is increased to φ = 0.80 or φ = 0.85. Two transient staging schedules are used, resulting in transitions from unstable to stable operation, and vice-versa. It is found that the characteristic instability decay times are dependent on the amount of fuel staging in the center nozzle. It is also found that the decay time constants differ from the growth time constants, indicating hysteresis in stability transition points. High speed CH* chemiluminescence images in combination with dynamic pressure measurements are used to determine the instantaneous phase difference between the heat release rate fluctuation and the combustor pressure fluctuation throughout the combustor. This analysis shows that the instability onset process is different from the instability decay process.

Assessment of the Potential of Combined Micro Gas Turbine and High Temperature Fuel Cell Systems

2002 ◽  
Author(s):  
Dieter Bohn ◽  
Nathalie Po¨ppe ◽  
Joachim Lepers
Keyword(s):  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Advanced Materials ◽  
Cell Systems ◽  
Micro Gas Turbine ◽  
Technological Assessment

The present paper reports a detailed technological assessment of two concepts of integrated micro gas turbine and high temperature (SOFC) fuel cell systems. The first concept is the coupling of micro gas turbines and fuel cells with heat exchangers, maximising availability of each component by the option for easy stand-alone operation. The second concept considers a direct coupling of both components and a pressurised operation of the fuel cell, yielding additional efficiency augmentation. Based on state-of-the-art technology of micro gas turbines and solid oxide fuel cells, the paper analyses effects of advanced cycle parameters based on future material improvements on the performance of 300–400 kW combined micro gas turbine and fuel cell power plants. Results show a major potential for future increase of net efficiencies of such power plants utilising advanced materials yet to be developed. For small sized plants under consideration, potential net efficiencies around 70% were determined. This implies possible power-to-heat-ratios around 9.1 being a basis for efficient utilisation of this technology in decentralised CHP applications.

Determination of Cycle Configuration of Gas Turbines and Aircraft Engines by Optimization Procedure

1990 ◽  
Author(s):  
Yoshiharu Tsujikawa ◽  
Makoto Nagaoka
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Specific Impulse ◽  
Optimization Procedure ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Aircraft Engines ◽  
Scramjet Engine ◽  
Aero Engines

This paper is devoted to the analyses and optimization of simple and sophisticated cycles, particularly for various gas turbine engines and aero-engines (including scramjet engine) to achive the maximum performance. The optimization of such criteria as thermal efficiency, specific output and total performance for gas turbine engines, and overall efficiency, non-dimensional thrust and specific impulse for aero-engines have been performed by the optimization procedure with multiplier method. The comparisons of results with analytical solutions establishes the validity of the optimization procedure.

Sign in / Sign up

Export Citation Format

Share Document