The modified Myers boundary condition for swirling flow

2018 ◽  
Vol 847 ◽  
pp. 868-906 ◽  
Author(s):  
James R. Mathews ◽  
Vianney Masson ◽  
Stéphane Moreau ◽  
Hélène Posson
Keyword(s):  
Boundary Layer ◽  
Boundary Condition ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Swirling Flow ◽  
Azimuthal Velocity ◽  
Inviscid Flow ◽  
Layer Model ◽  
Quadratic Error ◽  
The Time Domain

This paper gives a modified Myers boundary condition in swirling inviscid flow, which differs from the standard Myers boundary condition by assuming a small but non-zero boundary layer thickness. The new boundary condition is derived and is shown to have the correct quadratic error behaviour with boundary layer thickness and also to agree with previous results when the swirl is set to zero. The boundary condition is initially derived for swirling flow with constant azimuthal velocity, but easily extends to radially varying swirling flow, with terms depending on the boundary layer model. The modified Myers boundary condition is then given in the time domain rather than in the frequency domain. The effect of the boundary layer profile is then considered, and shown to be small compared to the boundary layer thickness. The boundary condition is then used to analyse the eigenmodes and Green’s function in a realistic flow. Modelling the thickness of the boundary layer properly is shown to be essential in order to get accurate results.

scholarly journals Suction/Injection Effects on the Swirling Flow of a Reiner-Rivlin Fluid near a Rough Surface

2015 ◽  
Vol 2015 ◽  
pp. 1-5 ◽  
Author(s):  
Bikash Sahoo ◽  
Sébastien Poncet ◽  
Fotini Labropulu
Keyword(s):  
Boundary Layer ◽  
Boundary Conditions ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Swirling Flow ◽  
Velocity Profiles ◽  
Partial Slip ◽  
Injection Velocity ◽  
Slip Boundary Conditions ◽  
Slip Boundary

The similarity equations for the Bödewadt flow of a non-Newtonian Reiner-Rivlin fluid, subject to uniform suction/injection, are solved numerically. The conventional no-slip boundary conditions are replaced by corresponding partial slip boundary conditions, owing to the roughness of the infinite stationary disk. The combined effects of surface slip (λ), suction/injection velocity (W), and cross-viscous parameter (L) on the momentum boundary layer are studied in detail. It is interesting to find that suction dominates the oscillations in the velocity profiles and decreases the boundary layer thickness significantly. On the other hand, injection has opposite effects on the velocity profiles and the boundary layer thickness.

Effects of a Source-Type Hypersonic Free Stream on the Flow Field about an Axisymmetric Cone

1966 ◽  
Vol 17 (2) ◽  
pp. 161-176
Author(s):  
Stuart B. Savage
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Layer Thickness ◽  
Surface Pressure ◽  
Shock Layer ◽  
Boundary Layer Thickness ◽  
Free Stream ◽  
Inviscid Flow ◽  
Source Type ◽  
Displacement Thickness

SummaryMost hypervelocity tunnels presently make use of conical or wedge type nozzles which produce source-type flow non-uniformities in the test section. The present paper considers the effects of such free-stream non-uniformities on the flow fields about slender axisymmetric cones. The inviscid flow is considered within the framework of the Newtonian expansion procedure of Cole and simple expressions are obtained for the flow field properties in the shock layer. This inviscid analysis predicts that a free-stream gradient of a magnitude typical of present hypervelocity test facilities can cause sizeable reductions in surface pressure and increased shock-layer thickness at the aft end of long slender conical models. The cone pressure, accounting for the viscous-inviscid interaction, is obtained by applying the inviscid analysis in tangent-cone fashion to the effective body (i.e. physical cone plus boundary-layer displacement thickness). Cheng’s simple equation is used to approximate the hypersonic boundary-layer development. Large increases in the boundary-layer thickness at the aft end of the model are predicted as a consequence of the source flow effects. The analyses agree well with experimental measurements of surface pressure and boundary-layer thickness made on a 5° half-angle cone tested in the Republic 24 inch Longshot I hypervelocity shock tunnel.

scholarly journals The role of thermal radiation on the boundary layer past a stationary flat plate with constant surface boundary condition

2021 ◽  
Vol 1 (2) ◽  
pp. 7-11
Author(s):  
Gabriel Samaila
Keyword(s):  
Boundary Layer ◽  
Boundary Condition ◽  
Differential Equations ◽  
Prandtl Number ◽  
Thermal Radiation ◽  
Flat Plate ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Surface Boundary ◽  
Surface Boundary Condition

This study is devoted to investigating the importance of thermal radiation on the boundary layer over a horizontal surface considering classical constant surface boundary condition. The mathematical model consists of coupled two-dimensional partial differential equations which are transformed to the set of ordinary differential equations via the similarity transformation. The final set of dimensionless equations is solved numerically using Runge Kutta Fehlberg (RKF45) method in Maple software. The significant effect of the thermal radiation is examined using four fluids namely; water, Sulphur oxide, air and mercury whose respective Prandtl numbers are 7, 2, 0.72 and 0.044. The influence of other prominent parameters affecting the flow formation and temperature profile is demonstrated using tables and graphs. The results indicated that the thermal boundary layer thickness could be increase by reducing the Prandtl number. The results also showed that increasing the thermal radiation parameter has a positive impact on the boundary layer thickness. The heat transfer rate could be improved by increasing thermal radiation or decreased by increasing the values of the Prandtl number. Regarding the temperature gradient, an observable increasing is seen far from the flat plate with the growing of thermal radiation whereas the opposite trend is true near the plate surface.

EFFECTS OF BOUNDARY-LAYER THICKNESS ON UNSTEADY FLOW CHARACTERISTICS INSIDE OPEN CAVITIES AT SUBSONIC AND TRANSONIC SPEEDS

2012 ◽  
Vol 19 ◽  
pp. 206-213
Author(s):  
DANG-GUO YANG ◽  
JIAN-QIANG LI ◽  
ZHAO-LIN FAN ◽  
XIN-FU LUO
Keyword(s):  
Boundary Layer ◽  
Unsteady Flow ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Sound Pressure ◽  
Flow Characteristics ◽  
Open Cavity ◽  
Aerodynamic Noise ◽  
Sustained Oscillation ◽  
Cavity Depth

An experimental study was conducted in a 0.6m by 0.6m wind-tunnel to analyze effects of boundary-layer thickness on unsteady flow characteristics inside a rectangular open cavity at subsonic and transonic speeds. The sound pressure level (SPL) distributions at the centerline of the cavity floor and Sound pressure frequency spectrum (SPFS) characteristics on some measurement positions presented herein was obtained with cavity length-to-depth ratio (L/D) of 8 over Mach numbers (Ma) of 0.6 and 1.2 at a Reynolds numbers (Re) of 1.23 × 107 and 2.02 × 107 per meter under different boundary-layer thickness to cavity-depth ratios (δ/D). The experimental angle of attack, yawing and rolling angles were 0°. The results indicate that decrease in δ/D leads to severe flow separation and unsteady pressure fluctuation, which induces increase in SPL at same measurement points inside the cavity at Ma of 0.6. At Ma of 1.2, decrease in δ/D results in enhancing compressible waves. Generally, decrease in δ/D induces more flow self-sustained oscillation frequencies. It also makes severer aerodynamic noise inside the open cavity.

Boundary Layer Closure and Heat Transfer in Constant Base Pressure and Simple Wave Guns

1978 ◽  
Vol 100 (4) ◽  
pp. 690-696 ◽  
Author(s):  
A. D. Anderson ◽  
T. J. Dahm
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Method Of Characteristics ◽  
Simple Wave ◽  
Momentum Equation ◽  
Base Pressure ◽  
Two Dimensional ◽  
The Method Of Characteristics

Solutions of the two-dimensional, unsteady integral momentum equation are obtained via the method of characteristics for two limiting modes of light gas launcher operation, the “constant base pressure gun” and the “simple wave gun”. Example predictions of boundary layer thickness and heat transfer are presented for a particular 1 in. hydrogen gun operated in each of these modes. Results for the constant base pressure gun are also presented in an approximate, more general form.

The structure of a highly decelerated axisymmetric turbulent boundary layer

2021 ◽  
Vol 929 ◽  
Author(s):  
N. Agastya Balantrapu ◽  
Christopher Hickling ◽  
W. Nathan Alexander ◽  
William Devenport
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Shear Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Large Scale ◽  
Convection Velocity ◽  
Mean Flow ◽  
Mean Velocity ◽  
The Mean

Experiments were performed over a body of revolution at a length-based Reynolds number of 1.9 million. While the lateral curvature parameters are moderate ( $\delta /r_s < 2, r_s^+>500$ , where $\delta$ is the boundary layer thickness and r s is the radius of curvature), the pressure gradient is increasingly adverse ( $\beta _{C} \in [5 \text {--} 18]$ where $\beta_{C}$ is Clauser’s pressure gradient parameter), representative of vehicle-relevant conditions. The mean flow in the outer regions of this fully attached boundary layer displays some properties of a free-shear layer, with the mean-velocity and turbulence intensity profiles attaining self-similarity with the ‘embedded shear layer’ scaling (Schatzman & Thomas, J. Fluid Mech., vol. 815, 2017, pp. 592–642). Spectral analysis of the streamwise turbulence revealed that, as the mean flow decelerates, the large-scale motions energize across the boundary layer, growing proportionally with the boundary layer thickness. When scaled with the shear layer parameters, the distribution of the energy in the low-frequency region is approximately self-similar, emphasizing the role of the embedded shear layer in the large-scale motions. The correlation structure of the boundary layer is discussed at length to supply information towards the development of turbulence and aeroacoustic models. One major finding is that the estimation of integral turbulence length scales from single-point measurements, via Taylor's hypothesis, requires significant corrections to the convection velocity in the inner 50 % of the boundary layer. The apparent convection velocity (estimated from the ratio of integral length scale to the time scale), is approximately 40 % greater than the local mean velocity, suggesting the turbulence is convected much faster than previously thought. Closer to the wall even higher corrections are required.

Magnetohydrodynamics Williamson Fluid Comprising Gyrotactic Microorganisms Flows Through a Permeable Stretching Layer with Variable Fluid Properties

2020 ◽  
Vol 9 (4) ◽  
pp. 375-387
Author(s):  
Amit Parmar ◽  
Rakesh Choudhary ◽  
Krishna Agarwal
Keyword(s):  
Boundary Layer ◽  
Velocity Profile ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Schmidt Number ◽  
Gyrotactic Microorganisms ◽  
Williamson Fluid ◽  
Non Linear ◽  
Fluid Properties ◽  
Variable Prandtl Number

The present study shows the impacts of Williamson fluid with magnetohydrodynamics flow containing gyrotactic microorganisms under the variable fluid property past permeable stretching sheet. Variable Prandtl number, mass Schmidt number, and gyrotactic microorganisms Schmidt number were all considered. The momentum, energy, mass, and microorganism equations’ governing PDEs are converted into nonlinear coupled ODEs and numerically solved with the bvp4c solver using suitable transformations. The main outcome of this study is that Williamson fluid parameter constantly decreases in velocity profile, however reverse effects can be shown in temperature profile. Also, M parameter and Kp parameter enhance the heat transfer rate, concentration rate and microorganisms boundary layer thickness but declines in momentum boundary layer thickness and velocity profile. The aim of this research is to see how velocity slide, temperature jump, concentration slip, and microorganism slip affect MHD Williamson fluid flow with gyrotactic microorganisms over a leaky surface embedded in spongy medium, with non-linear radiation and non-linear chemical reaction.

Freestream Flow Effects on Film Effectiveness and Heat Transfer Coefficient Augmentation for Compound Angle Shaped Holes

2017 ◽  
Author(s):  
Joshua B. Anderson ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
Zachary Webster
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Layer Thickness ◽  
Film Cooling ◽  
Gas Turbines ◽  
Boundary Layer Thickness ◽  
Adiabatic Effectiveness ◽  
Compound Angle

The use of compound-angled shaped film cooling holes in gas turbines provides a method for cooling regions of extreme curvature on turbine blades or vanes. These configurations have received surprisingly little attention in the film cooling literature. In this study, a row of laid-back fanshaped holes based on an open-literature design, were oriented at a 45-degree compound angle to the approaching freestream flow. In this study, the influence of the approach flow boundary layer thickness and character were experimentally investigated. A trip wire and turbulence generator were used to vary the boundary layer thickness and freestream conditions from a thin laminar boundary layer flow to a fully turbulent boundary layer and freestream at the hole breakout location. Steady-state adiabatic effectiveness and heat transfer coefficient augmentation were measured using high-resolution IR thermography, which allowed the use of an elevated density ratio of DR = 1.20. The results show adiabatic effectiveness was generally lower than for axially-oriented holes of the same geometry, and that boundary layer thickness was an important parameter in predicting effectiveness of the holes. Heat transfer coefficient augmentation was highly dependent on the freestream turbulence levels as well as boundary layer thickness, and significant spatial variations were observed.

Sign in / Sign up

Export Citation Format

Share Document