Strain behaviour of a friction stir processed superplastic aluminium alloy sheet during free inflation tests

2016 ◽  
Vol 23 ◽  
pp. 287-295 ◽  
Author(s):  
Donato Sorgente ◽  
Sabina Luisa Campanelli ◽  
Alessandro Stecchi ◽  
Nicola Contuzzi
Keyword(s):  
Aluminium Alloy ◽  
Alloy Sheet ◽  
Friction Stir ◽  
Strain Behaviour

scholarly journals Influences of Pin Shape on a High Rotation Speed Friction Stir Welding Joint of a 6061-T6 Aluminum Alloy Sheet

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 987 ◽  
Author(s):  
Yang Zhou ◽  
Shujin Chen ◽  
Jiayou Wang ◽  
Penghao Wang ◽  
Jingyu Xia
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Rotation Speed ◽  
Alloy Sheet ◽  
Aluminum Alloy Sheet ◽  
Welding Quality ◽  
Nugget Zone ◽  
Friction Stir ◽  
High Rotation Speed ◽  
S Curve

In order to explore the influences of different pins on the weld based on the specialty of the aluminium alloy sheet welding, three kinds of pins were chosen to perform high rotation speed friction stir welding on a 1 mm thick 6061-T6 aluminium alloy in this study. The microstructure and mechanical properties of the joints were analysed at the same time. When the rotation speed was 11,000 rpm and the welding speed was 300 mm/min, more sufficient stirring and a better joint (the tensile strength reaches 87.2% of the base metal) can be obtained with the pin design of a quadrangular frustum pyramid. The pattern of the weld cross section was a “flat T” and no obvious “S curve” was found in nugget zone (NZ). Heat affected zone (HAZ) and thermo-mechanically affected zone (TMAZ) were also narrow. The results demonstrate that the proportion of low angle boundaries in each area of the weld is lower than that of traditional Friction Stir Welding (FSW). The grain size of NZ is significantly refined and the proportion of low angle boundaries is only 20.1%, which have improved the welding quality.

scholarly journals Analysis of the strain behaviour of a friction stir processed superplastic aluminium alloy

2015 ◽  
Vol 21 ◽  
pp. 04006
Author(s):  
Donato Sorgente ◽  
Sabina Luisa Campanelli ◽  
Alessandro Stecchi ◽  
Nicola Contuzzi
Keyword(s):  
Aluminium Alloy ◽  
Friction Stir ◽  
Strain Behaviour

scholarly journals Friction stir welding of 2024-T3 aluminium alloy sheet with sheet pre-heating

2018 ◽  
Vol 52 (3) ◽  
pp. 283-288
Author(s):  
A. Kubit ◽  
R. Kluz ◽  
K. Ochałek ◽  
D. Wydrzyński ◽  
T. Trzepieciński
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Alloy Sheet ◽  
Friction Stir

scholarly journals Optimization of Friction Stir Welding Process Parameters to joint 7075-T6 Aluminium Alloy by Utilizing Taguchi Technique

2019 ◽  
Vol 25 (5) ◽  
pp. 1-15 ◽  
Author(s):  
Abbas Akram Abbas ◽  
Hazim Hattem Abdulkadhum
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Welding Process ◽  
Ultimate Tensile Stress ◽  
Alloy Sheet ◽  
Welding Parameters ◽  
Taguchi Technique ◽  
Friction Stir ◽  
Friction Stir Welding Process ◽  
Thread Pitch

In this study, a 3 mm thickness 7075-T6 aluminium alloy sheet was used in the friction stir welding process. Using the design of experiment to reduce the number of experiments and to obtain the optimum friction stir welding parameters by utilizing Taguchi technique based on the ultimate tensile test results. Orthogonal array of L9 (33) was used based on three numbers of the parameters and three levels for each parameter, where shoulder-workpiece interference depth (0.20, 0.25, and 0.3) mm, pin geometry (cylindrical thread flat end, cylindrical thread with 3 flat round end, cylindrical thread round end), and thread pitch (0.8, 1, and 1.2) mm) this technique executed by Minitab 17 software. The results showed that the optimum friction stir welding parameters were 0.25 mm shoulder-workpiece interference depth, cylindrical thread flat end pin shape, 1.2 mm thread pitch depending on the S ̸ N ratio and ANOVA analysis and the welding efficiency was 93.3% based on the ultimate tensile stress.  

Microstructural aspects and mechanical properties of friction stir welded AA2024-T3 aluminium alloy sheet

2011 ◽  
Vol 32 (10) ◽  
pp. 4684-4688 ◽  
Author(s):  
Andreza S. Franchim ◽  
Fernando F. Fernandez ◽  
Dilermando N. Travessa
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Alloy Sheet ◽  
Friction Stir

Microstructure, Tool Design and Mechanical Properties Evolution of Friction Stir Welded Aluminium Alloy

2010 ◽  
Vol 5 (2) ◽  
pp. 55-63
Author(s):  
G. Raghu Babu ◽  
◽  
K.G.K. Murti ◽  
G. Ranga Janardhana ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Tool Design ◽  
Friction Stir
Sign in / Sign up

Export Citation Format

Share Document