Microstructural aspects and mechanical properties of friction stir welded AA2024-T3 aluminium alloy sheet

2011 ◽  
Vol 32 (10) ◽  
pp. 4684-4688 ◽  
Author(s):  
Andreza S. Franchim ◽  
Fernando F. Fernandez ◽  
Dilermando N. Travessa
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Alloy Sheet ◽  
Friction Stir

Microstructure, Tool Design and Mechanical Properties Evolution of Friction Stir Welded Aluminium Alloy

2010 ◽  
Vol 5 (2) ◽  
pp. 55-63
Author(s):  
G. Raghu Babu ◽  
◽  
K.G.K. Murti ◽  
G. Ranga Janardhana ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Tool Design ◽  
Friction Stir

Study on the Formability of Aluminium Alloy Sheets at Room and Elevated Temperatures

2016 ◽  
Vol 877 ◽  
pp. 393-399
Author(s):  
Jia Zhou ◽  
Jun Ping Zhang ◽  
Ming Tu Ma
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Elevated Temperature ◽  
Aluminium Alloy ◽  
Aluminium Alloys ◽  
Elevated Temperatures ◽  
Hot Stamping ◽  
Natural Aging ◽  
Alloy Sheet ◽  
Aluminum Alloy Sheet

This paper presents the main achievements of a research project aimed at investigating the applicability of the hot stamping technology to non heat treatable aluminium alloys of the 5052 H32 and heat treatable aluminium alloys of the 6016 T4P after six months natural aging. The formability and mechanical properties of 5052 H32 and 6016 T4P aluminum alloy sheets after six months natural aging under different temperature conditions were studied, the processing characteristics and potential of the two aluminium alloy at room and elevated temperature were investigated. The results indicated that the 6016 aluminum alloy sheet exhibit better mechanical properties at room temperature. 5052 H32 aluminum alloy sheet shows better formability at elevated temperature, and it has higher potential to increase formability by raising the temperature.

Effect of FSP on Strength and Fracture Toughness of Aluminium Alloy 7000

2018 ◽  
Vol 877 ◽  
pp. 20-25
Author(s):  
P.K. Mandal
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Aluminium Alloy ◽  
Axial Force ◽  
Weight Ratio ◽  
High Strength ◽  
Hardness Measurement ◽  
Traverse Speed ◽  
Age Hardening ◽  
Friction Stir

The cast Al-Zn-Mg 7000 alloy has become one of the most potential structural materials in many engineering fields such as aircraft body, automotive casting due to their high strength to weight ratio, strong age hardening ability, competitive weight savings, attractive mechanical properties and improvement of thermal properties. The cast aluminium alloy has been modified of surface layer through a solid-state technique is called friction stir process (FSP). But basic principle has been followed by friction stir welding (FSW). This process can be used to locally refine microstructures and eliminate casting defects in selected locations, where mechanical properties improvements can enhance component performance and service life. However, some specified process parameters have adopted during experimental works. Those parameters are tool rotation speed (720 rpm), plate traverse speed (80 mm/min), axial force (15 kN), and tool design (i.e., pin height 3.5 mm and pin diameter 3.0 mm), respectively. The main mechanism behind this process likely to axial force and frictional force acting between the tool shoulder and workpiece results in intense heat generation and plastically soften the process material. The specified ratio of rotational speed (720 rpm) to traverse speed (80 mm/min) is considered 9 as low heat input during FSP and its entails low Zn vaporization problem results as higher fracture toughness of aluminium alloy. It is well known that the stirred zone (SZ) consists of refine equiaxed grains produced due to dynamic recrystallization. FSP has been proven to innovatively enhancing of various properties such as formability, hardness and fracture toughness (32.60 MPa√m). The hardness and fracture toughness of double passes AC+FSP aluminium alloy had been investigated by performing Vicker’s hardness measurement and fracture toughness (KIC)(ASTM E-399 standard) tests. Detailed observations with optical microscopy, Vicker’s hardness measurement, SEM, TEM, and DTA analysis have conducted to analyse microstructure and fracture surfaces of double passes FSP aluminium alloy.

Sign in / Sign up

Export Citation Format

Share Document