Influence of soil non-homogeneity on the base shear force of piled structures subjected to harmonic seismic waves

2020 ◽  
Vol 215 ◽  
pp. 110658
Author(s):  
C. Medina ◽  
G.M. Álamo ◽  
J.J. Aznárez ◽  
L.A. Padrón ◽  
O. Maeso
Keyword(s):  
Shear Force ◽  
Seismic Waves ◽  
Base Shear

scholarly journals Effect of Bottom Geometry on the Natural Sloshing Motion of Water Inside Tanks: An Experimental Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 605
Author(s):  
Antonio Agresta ◽  
Nicola Cavalagli ◽  
Chiara Biscarini ◽  
Filippo Ubertini
Keyword(s):  
Energy Dissipation ◽  
Water Depth ◽  
Shear Force ◽  
Experimental Tests ◽  
Shear Load ◽  
Damping Properties ◽  
Base Shear ◽  
Structure Interaction ◽  
Sloshing Phenomenon ◽  
Key Aspects

The present work aims at understanding and modelling some key aspects of the sloshing phenomenon, related to the motion of water inside a container and its effects on the substructure. In particular, the attention is focused on the effects of bottom shapes (flat, sloped and circular) and water depth ratio on the natural sloshing frequencies and damping properties of the inner fluid. To this aim, a series of experimental tests has been carried out on tanks characterised by different bottom shapes installed over a sliding table equipped with a shear load cell for the measurement of the dynamic base shear force. The results are useful for optimising the geometric characteristics of the tank and the fluid mass in order to obtain enhanced energy dissipation performances by exploiting fluid–structure interaction effects.

The effect of element strength assignment on the torsional response of stiffness-eccentric systems

2013 ◽  
Vol 40 (7) ◽  
pp. 655-662
Author(s):  
George K. Georgoussis
Keyword(s):  
Structural Design ◽  
Shear Force ◽  
Ground Motions ◽  
Building Structures ◽  
Centre Of Mass ◽  
Base Shear ◽  
Structural Behaviour ◽  
Torsional Response ◽  
Building Models ◽  
Storey Building

Building structures of low or medium height are usually designed with a pseudostatic approach using a base shear much lower than that predicted from an elastic spectrum. Given this shear force, the objective of this paper is to evaluate the effect of the element strength assignment (as determined by several building codes) on the torsional response of inelastic single-storey eccentric structures and to provide guidelines for minimizing this structural behaviour. It is demonstrated that the expected torque about the centre of mass (CM) may be, with equal probability, positive (counterclockwise) or negative (clockwise). This result means that the torsional strength should also be provided in equal terms in both rotational directions, and therefore the base shear and torque (BST) surface of a given system must be symmetrical (or approximately symmetrical). In stiffness-eccentric systems, appropriate BST surfaces may be obtained when a structural design is based on a pair of design eccentricities in a symmetrical order about CM, and this is shown in representative single-storey building models under characteristic ground motions.

Basic Theory of Simplified Dynamic Model for Spherical Tank Considering Swinging Effect

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Yuan Lü ◽  
Jiangang Sun ◽  
Zongguang Sun ◽  
Lifu Cui ◽  
Zhen Wang
Keyword(s):  
Dynamic Model ◽  
Shear Force ◽  
Velocity Potential ◽  
Fluid Pressure ◽  
Site Conditions ◽  
Base Shear ◽  
Site Condition ◽  
Spherical Tank ◽  
Overturning Moment ◽  
The Difference

Abstract Consider the swinging effect of spherical tank, the theory of velocity potential is adopted, and a reasonable potential function is derived according to the boundary conditions. Further, the dynamic fluid pressure, the wave height of the liquid, the shear force and the overturning moment at the bottom of the spherical tank is calculated, and a simplified dynamic model of spherical tank considering liquid sloshing and swinging effect was constructed. The seismic response was studied and compared with the results without considering the swing effect. The results show that: for Ι, II site conditions, base shear force and overturning moment of considering the swing effect is slightly smaller than when nonconsidering and the difference rate between the two is very small. III–IV site conditions, each condition value of considering the swing effect is larger than when nonconsidering and the difference rate between the two is relatively large. Aseismic design of spherical tank and the influence of swing effect should be considered if the site condition is III and IV, and if site I and II, they can be ignored.

scholarly journals Seismic Fragility Assessment of Base-Isolated Steel Water Storage Tank

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Zhuo Zhao ◽  
Xiaowei Lu ◽  
Yu Guo ◽  
Xiaofeng Zhao
Keyword(s):  
Storage Tank ◽  
Shear Force ◽  
Fragility Curves ◽  
Water Storage ◽  
Time History ◽  
Seismic Fragility ◽  
Coefficient Of Determination ◽  
Base Shear ◽  
Water Storage Tank ◽  
Demand Models

Steel water storage tanks (WSTs) are among the important components of water treatment industry facilities that are expected to remain functional and applicable after strong earthquakes. In this study, the seismic vulnerability of base-isolated steel WST is investigated. A three-dimensional finite element stick model of the targeted tank is created using OpenSees. This model is capable of reproducing convective, impulsive, and rigid responses of fluid-tank systems. Time-history responses of convective displacement, bearing displacement, and base shear force for base-isolated tank subjected to a typical ground motion are compared. Furthermore, time-history analysis based on a suite of 80 ground motions is conducted. The seismic demand models for various responses are established and the most efficient intensity measure (IM) is determined based on the dispersion and coefficient of determination. Seismic fragility curves for different responses are derived for all three damage states using cloud analysis. The results from this study reveal that (i) the convective displacement is significantly greater than bearing displacement; (ii) peak ground displacement (PGD) is the most efficient and sufficient IM for the targeted tank; and (iii) the characteristic of isolation bearing significantly influences the seismic fragilities of convective displacement and bearing displacement and has a little impact on base shear force, which makes the selection of the proper characteristic parameters for isolation bearing very essential. The analysis technique and procedure mentioned above as well as derived insights are of significance to general liquid storage tank system configuration.

Experimental Observations and Numerical Simulations of Wave Impact Forces on Recurved Parapets Mounted Above a Vertical Wall

2009 ◽  
Author(s):  
David Newborn ◽  
Nels Sultan ◽  
Pierre Beynet ◽  
Tim Maddux ◽  
Sungwon Shin ◽  
...  
Keyword(s):  
Numerical Model ◽  
Numerical Simulations ◽  
Shear Force ◽  
Experimental Testing ◽  
Vertical Wall ◽  
Experimental Tests ◽  
Vertical Force ◽  
Base Shear ◽  
Wave Impact ◽  
Overturning Moment

Large-scale hydraulic model tests and detail numerical model investigations were conducted on recurved wave deflecting structures to aid in the design of wave overtopping mitigation for vertical walls in shallow water. The incident wave and storm surge conditions were characteristic return period events for an offshore island on the North Slope of Alaska. During large storm events, despite depth-limited wave heights, a proposed vertical wall extension was susceptible to wave overtopping, which could potentially cause damage to equipment. Numeric calculations were conducted prior to the experimental tests and were used to establish the relative effectiveness of several recurved parapet concepts. The numerical simulations utilized the COrnell BReaking waves and Structures (COBRAS) fluid modeling program, which is a Volume-of-Fluid (VOF) model based on Reynolds Averaged Navier-Stokes equations [1] [2]. The experimental testing was conducted in the Large Wave Flume (LWF) at Oregon State University, O.H. Hinsdale Wave Research Laboratory. The experimental test directly measured the base shear force, vertical force, and overturning moment applied to the recurved parapets due to wave forcing. Wave impact pressure on the parapet and water particle velocities seaward of the wall were also measured. Results from the experimental testing include probability of exceedance curves for the base shear force, vertical force, and overturning moment for each storm condition. Qualitative comparisons between the experimental tests and the COBRAS simulations show that the numerical model provides realistic flow on and over the parapet.

scholarly journals Shaking Table Test for Evaluating the Seismic Performance of Steel Frame Retrofitted by Buckling-Restrained Braces

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Tingting Wang ◽  
Jianhua Shao ◽  
Chao Zhao ◽  
Wenjin Liu ◽  
Zhanguang Wang
Keyword(s):  
Seismic Performance ◽  
Shear Force ◽  
Seismic Waves ◽  
Shaking Table Test ◽  
Steel Frame ◽  
Shaking Table ◽  
Frame Structure ◽  
Acceleration Response ◽  
Buckling Restrained Brace ◽  
Interstory Drift

To investigate the seismic performance of buckling-restrained braces under the earthquake action, the shaking table test with a two-story 1/4 scale model is carried out for the ordinary pure steel frame and the buckling-restrained bracing steel frame with low-yield-point steel as the core plate. The failure modes, dynamic characteristics, acceleration response, interstory drift ratio, strain, shear force, and other mechanical properties of those two comparative structures subjected to different levels of seismic waves are mainly evaluated by the experiment. The test results show that under the action of seismic waves with different intensities, the apparent observations of damage occur in the pure frame structure, while no obvious or serious damage in the steel members of BRB structure is observed. With the increase in loading peak acceleration for the earthquake waves, the natural frequency of both structures gradually decreases and the damping ratio gradually increases. At the end of the test, the stiffness degradation rate of the pure frame structure is 11.2%, while that of the buckling-restrained bracing steel frame structure is only 5.4%. The acceleration response of the buckling-restrained bracing steel frame is smaller than that of the pure steel frame, and the acceleration amplification factor at the second story is larger than that at the first story for both structures. The average interstory drift ratios are, respectively, 1/847 and 1/238 for the pure steel frame under the frequent earthquake and rare earthquake and are 1/3000 and 1/314 for the buckling-restrained bracing steel frame, which reveals that the reduction rate of lateral displacement reaches a maximum of 71.71% after the installation of buckling-restrained brace in the pure steel frame. The strain values at each measuring point of the structural beam and column gradually increase with the increase of the peak seismic acceleration, but the strain values of the pure steel frame are significantly larger than those of the buckling-restrained bracing steel frame, which indicates that the buckling-restrained brace as the first seismic line of defense in the structure can dramatically protect the significant structural members. The maximum shear force at each floor of the structure decreases with the increase in height, and the shear response of the pure frame is apparently higher than that of the buckling-restrained bracing structure.

scholarly journals Pembandingan Perancangan Bangunan Tahan Gempa Menggunakan SNI 1726:2012 Dan SNI 1726:2019

2021 ◽  
Vol 18 (1) ◽  
pp. 88-99
Author(s):  
Azis Wicaksana ◽  
Anis Rosyidah
Keyword(s):  
Shear Force ◽  
Seismic Analysis ◽  
Building Design ◽  
Response Analysis ◽  
Base Shear ◽  
Seismic Resistant ◽  
Story Drift ◽  
Moment Resisting ◽  
Special Moment Resisting Frame ◽  
Spectrum Response

Indonesia has a code for designing a seismic-resistant building, which has always improved year after year. Start from Peraturan Perencanaan Tahan Gempa Indonesia Untuk Gedung (PPTI-UG) 1983, SNI 1726:2002, SNI 1726:2012, and the latest one is SNI 1726:2019. SNI 1726:2019 experienced some renewal on designing a seismic-resistant building. This research aims to compare spectrum response design and the structural behavior between seismic-resistant building design using SNI 1726:2012 and SNI 1726:2019. The reviewed structure behaviors are base shear force (V), drift (δmax), and story drift (Δ). The study compares the detail of the structural components as well as using SNI 2847:2013 and SNI 2847:2019. The research uses a 10-story building modeling that serves as an apartment building and located in the city of Banda Aceh. Seismic analysis using a spectrum response analysis with Special Moment Resisting Frame (SMRF) structure. The result showed that the peak acceleration (Sa) for the class sites of Medium Land (SD) and Hard Land (SC) were 11% and 26%, respectively, while for Soft Land (SE), there was no increase. The shear force in SNI 1726: 2019 has increased by 19.75% for the X direction and 19.97% for the Y direction. The increase in the shear force is directly proportional to the increase in drift and story drift. In the beam detailing and beam-column connection, there were no significant changes. While in the column detailing, there are additional provisions that cause the transverse reinforcement to be tighter.

scholarly journals Force Based Design and Direct Displacement Based Design for Dual System Structure

2019 ◽  
Vol 19 (3) ◽  
pp. 162
Author(s):  
Annisaa Dina Puspita ◽  
Anis Rosyidah
Keyword(s):  
Shear Force ◽  
Damage Control ◽  
Performance Level ◽  
Dual System ◽  
Reinforcement Ratio ◽  
System Structure ◽  
Building Structures ◽  
Base Shear ◽  
Direct Displacement Based Design ◽  
Displacement Based

The Force Based Design (FBD) and the Direct Displacement-Based Design (DDBD) are methods for designing seismic-resistant buildings. Building structures designed, are expected to be suitable with the purpose and usefulness of a building. For this reason, this study compares the performance of dual system structures using the DDBD and FBD methods that aim to prove better performance with consideration of safety against users during an earthquake. This research method uses design analysis method to compare the value of the base shear force, reinforcement ratio, and performance level using software for static nonlinear pushover analysis. The results showed the value of the base shear force x direction of the DDBD method was 17.57% smaller than the FBD method, whereas for the y direction the DDBD value was greater than 9.38% of the FBD. The value of the reinforcement ratio of the beam, column and shear wall results is greater DDBD than FBD. The actual drift of the DDBD and FBD methods is slightly different. So that both are at the same level of performance, namely damage control. The performance level has not reached the performance target of life safety design in DDBD, but the structure has met the level performance requirements for offices.

scholarly journals Performance of Six- and Ten-story Reinforced Concrete Buildings Designed by using Modified Partial Capacity Design (M-PCD) Method with 70% Shear Force Ratio

2021 ◽  
Vol 23 (2) ◽  
pp. 131-137
Author(s):  
Pamuda Pudjisuryadi ◽  
F. Wijaya ◽  
R. Tanuwijaya ◽  
B.C. Prasetyo ◽  
Benjamin Lumantarna
Keyword(s):  
Reinforced Concrete ◽  
Shear Force ◽  
Design Method ◽  
Base Shear ◽  
Reinforced Concrete Buildings ◽  
Capacity Design ◽  
Concrete Buildings ◽  
Force Ratio ◽  
Total Base ◽  
Nonlinear Static Procedure

One design alternative of earthquake resistant building is Partial Capacity Design (PCD) method. Unlike the commonly used capacity design method, PCD allows a safe failure mechanism which is called partial sidesway mechanism. In this mechanism, all beams and some columns are allowed to experience plastic damages while some selected columns are designed to remain elastic (called elastic columns). A new approach to predict the required strengths needed to design each structural member, called modified-PCD (M-PCD) is proposed. In this research six- and ten-story reinforced concrete buildings were designed using M-PCD, and their seismic performances are investigated. The base shear force resisted by the elastic columns was set to approximately 70% of the total base shear. Both nonlinear static procedure (NSP) and nonlinear dynamic procedure (NDP) are used to analyze the structures. The results show that the expected partial side sway mechanism is observed, and the drifts of the buildings are acceptable.

Sign in / Sign up

Export Citation Format

Share Document