scholarly journals Effect of Bottom Geometry on the Natural Sloshing Motion of Water Inside Tanks: An Experimental Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 605
Author(s):  
Antonio Agresta ◽  
Nicola Cavalagli ◽  
Chiara Biscarini ◽  
Filippo Ubertini
Keyword(s):  
Energy Dissipation ◽  
Water Depth ◽  
Shear Force ◽  
Experimental Tests ◽  
Shear Load ◽  
Damping Properties ◽  
Base Shear ◽  
Structure Interaction ◽  
Sloshing Phenomenon ◽  
Key Aspects

The present work aims at understanding and modelling some key aspects of the sloshing phenomenon, related to the motion of water inside a container and its effects on the substructure. In particular, the attention is focused on the effects of bottom shapes (flat, sloped and circular) and water depth ratio on the natural sloshing frequencies and damping properties of the inner fluid. To this aim, a series of experimental tests has been carried out on tanks characterised by different bottom shapes installed over a sliding table equipped with a shear load cell for the measurement of the dynamic base shear force. The results are useful for optimising the geometric characteristics of the tank and the fluid mass in order to obtain enhanced energy dissipation performances by exploiting fluid–structure interaction effects.

Experimental Observations and Numerical Simulations of Wave Impact Forces on Recurved Parapets Mounted Above a Vertical Wall

2009 ◽  
Author(s):  
David Newborn ◽  
Nels Sultan ◽  
Pierre Beynet ◽  
Tim Maddux ◽  
Sungwon Shin ◽  
...  
Keyword(s):  
Numerical Model ◽  
Numerical Simulations ◽  
Shear Force ◽  
Experimental Testing ◽  
Vertical Wall ◽  
Experimental Tests ◽  
Vertical Force ◽  
Base Shear ◽  
Wave Impact ◽  
Overturning Moment

Large-scale hydraulic model tests and detail numerical model investigations were conducted on recurved wave deflecting structures to aid in the design of wave overtopping mitigation for vertical walls in shallow water. The incident wave and storm surge conditions were characteristic return period events for an offshore island on the North Slope of Alaska. During large storm events, despite depth-limited wave heights, a proposed vertical wall extension was susceptible to wave overtopping, which could potentially cause damage to equipment. Numeric calculations were conducted prior to the experimental tests and were used to establish the relative effectiveness of several recurved parapet concepts. The numerical simulations utilized the COrnell BReaking waves and Structures (COBRAS) fluid modeling program, which is a Volume-of-Fluid (VOF) model based on Reynolds Averaged Navier-Stokes equations [1] [2]. The experimental testing was conducted in the Large Wave Flume (LWF) at Oregon State University, O.H. Hinsdale Wave Research Laboratory. The experimental test directly measured the base shear force, vertical force, and overturning moment applied to the recurved parapets due to wave forcing. Wave impact pressure on the parapet and water particle velocities seaward of the wall were also measured. Results from the experimental testing include probability of exceedance curves for the base shear force, vertical force, and overturning moment for each storm condition. Qualitative comparisons between the experimental tests and the COBRAS simulations show that the numerical model provides realistic flow on and over the parapet.

scholarly journals Material parametrization of natural rubber based compound and characterization of crack propagation under consideration of dissipative effects

2021 ◽  
Author(s):  
Dan Pornhagen ◽  
Konrad Schneider ◽  
Markus Stommel
Keyword(s):  
Energy Dissipation ◽  
Crack Propagation ◽  
Natural Rubber ◽  
Experimental Tests ◽  
Material Behavior ◽  
Prony Series ◽  
Material Forces ◽  
Cracking Behavior ◽  
Dissipative Effects

AbstractMost concepts to characterize crack propagation were developed for elastic materials. When applying these methods to elastomers, the question is how the inherent energy dissipation of the material affects the cracking behavior. This contribution presents a numerical analysis of crack growth in natural rubber taking energy dissipation due to the visco-elastic material behavior into account. For this purpose, experimental tests were first carried out under different load conditions to parameterize a Prony series as well as a Bergström–Boyce model with the results. The parameterized Prony series was then used to perform numerical investigations with respect to the cracking behavior. Using the FE-software system ANSYS and the concept of material forces, the influence and proportion of the dissipative components were discussed.

The effect of element strength assignment on the torsional response of stiffness-eccentric systems

2013 ◽  
Vol 40 (7) ◽  
pp. 655-662
Author(s):  
George K. Georgoussis
Keyword(s):  
Structural Design ◽  
Shear Force ◽  
Ground Motions ◽  
Building Structures ◽  
Centre Of Mass ◽  
Base Shear ◽  
Structural Behaviour ◽  
Torsional Response ◽  
Building Models ◽  
Storey Building

Building structures of low or medium height are usually designed with a pseudostatic approach using a base shear much lower than that predicted from an elastic spectrum. Given this shear force, the objective of this paper is to evaluate the effect of the element strength assignment (as determined by several building codes) on the torsional response of inelastic single-storey eccentric structures and to provide guidelines for minimizing this structural behaviour. It is demonstrated that the expected torque about the centre of mass (CM) may be, with equal probability, positive (counterclockwise) or negative (clockwise). This result means that the torsional strength should also be provided in equal terms in both rotational directions, and therefore the base shear and torque (BST) surface of a given system must be symmetrical (or approximately symmetrical). In stiffness-eccentric systems, appropriate BST surfaces may be obtained when a structural design is based on a pair of design eccentricities in a symmetrical order about CM, and this is shown in representative single-storey building models under characteristic ground motions.

Evidence of soil-structure interaction from modular full-scale field experimental tests

2021 ◽  
Author(s):  
Athanasios Vratsikidis ◽  
Dimitris Pitilakis ◽  
Anastasios Anastasiadis ◽  
Anastasios Kapouniaris
Keyword(s):  
Soil Structure ◽  
Experimental Tests ◽  
Full Scale ◽  
Soil Structure Interaction ◽  
Structure Interaction ◽  
Scale Field

Soil-Structure Interaction in Buildings from Earthquake Records

1990 ◽  
Vol 6 (4) ◽  
pp. 641-655 ◽  
Author(s):  
Gregory L. Fenves ◽  
Giorgio Serino
Keyword(s):  
Soil Structure ◽  
Dynamic Properties ◽  
Strong Motion ◽  
Longitudinal Direction ◽  
Soil Structure Interaction ◽  
Base Shear ◽  
Foundation Soil ◽  
Soil System ◽  
Structure Interaction ◽  
Building Foundation

An evaluation of the response of a fourteen story reinforced concrete building to the 1 October 1987 Whittier earthquake and 4 October 1987 aftershock shows significant effects of soil-structure interaction. A mathematical model of the building-foundation-soil system provides response quantities not directly available from the records. The model is calibrated using the dynamic properties of the building as determined from the processed strong motion records. Soil-structure interaction reduces the base shear force in the longitudinal direction of the building compared with the typical assumption in which interaction is neglected. The reduction in base shear for this building and earthquake is approximately represented by proposed building code provisions for soil-structure interaction.

Sign in / Sign up

Export Citation Format

Share Document