Dependence of yield point of crystals on forest dislocation density

1972 ◽  
Vol 4 (9) ◽  
pp. 1096-1098
Author(s):  
A. A. Alekseev
Keyword(s):  
Dislocation Density ◽  
Yield Point ◽  
Forest Dislocation

Plasticity of MoSi2 Below 900°C

1993 ◽  
Vol 322 ◽  
Author(s):  
H. Chang ◽  
R. Gibala
Keyword(s):  
Dislocation Density ◽  
Mechanical Behavior ◽  
Yield Point ◽  
Stress Strain ◽  
Temperature Range ◽  
Dislocation Plasticity

AbstractThe mechanical behavior of polycrystalline MoSi2 tested in compression at temperatures from 750°C to 950°C has been investigated. This material can be deformed to several percent strain without fracture at temperatures as low as 900°C. This same material prestrained at 1300°C and subsequently tested at lower temperatures can be deformed to substantial strain at 800°C, and even exhibits modest plasticity at 750°C. Both prestrained and unprestrained materials exhibit microcracking combined with dislocation substructures containing high densities of dislocations. Unprestrained MoSi2 exhibits a yield point in this temperature range which does not exist when it is prestrained. The stress-strain curves of the prestrained material in this temperature range are similar qualitatively to those of the unprestrained material at 1100°C and above. These observations suggest that at these temperatures MoSi2 is a dislocation density limited material which can deform by dislocation plasticity processes if a sufficient dislocation density is available.

Observations of dislocation interactions with recrystallized grain boundaries

1988 ◽  
Vol 46 ◽  
pp. 628-629
Author(s):  
C. W. Price
Keyword(s):  
Dislocation Density ◽  
Grain Boundary ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Dislocation Structure ◽  
Hot Deformation ◽  
Static Recrystallization ◽  
High Dislocation Density ◽  
High Angle ◽  
Dislocation Interactions

Little evidence exists on the interaction of individual dislocations with recrystallized grain boundaries, primarily because of the severely overlapping contrast of the high dislocation density usually present during recrystallization. Interesting evidence of such interaction, Fig. 1, was discovered during examination of some old work on the hot deformation of Al-4.64 Cu. The specimen was deformed in a programmable thermomechanical instrument at 527 C and a strain rate of 25 cm/cm/s to a strain of 0.7. Static recrystallization occurred during a post anneal of 23 s also at 527 C. The figure shows evidence of dissociation of a subboundary at an intersection with a recrystallized high-angle grain boundary. At least one set of dislocations appears to be out of contrast in Fig. 1, and a grainboundary precipitate also is visible. Unfortunately, only subgrain sizes were of interest at the time the micrograph was recorded, and no attempt was made to analyze the dislocation structure.

Investigation of shock-wave deformation history from recovered structure

1986 ◽  
Vol 44 ◽  
pp. 434-435
Author(s):  
M.A. Mogilevsky ◽  
L.S. Bushnev
Keyword(s):  
Shock Wave ◽  
Plastic Deformation ◽  
Dislocation Density ◽  
Shock Waves ◽  
Shock Front ◽  
Single Crystals ◽  
Residual Deformation ◽  
Deformation Structure ◽  
Deformation History ◽  
Deformation Velocity

Single crystals of Al were loaded by 15 to 40 GPa shock waves at 77 K with a pulse duration of 1.0 to 0.5 μs and a residual deformation of ∼1%. The analysis of deformation structure peculiarities allows the deformation history to be re-established.After a 20 to 40 GPa loading the dislocation density in the recovered samples was about 1010 cm-2. By measuring the thickness of the 40 GPa shock front in Al, a plastic deformation velocity of 1.07 x 108 s-1 is obtained, from where the moving dislocation density at the front is 7 x 1010 cm-2. A very small part of dislocations moves during the whole time of compression, i.e. a total dislocation density at the front must be in excess of this value by one or two orders. Consequently, due to extremely high stresses, at the front there exists a very unstable structure which is rearranged later with a noticeable decrease in dislocation density.

Study of the character and causes of destruction of the cardan shaft of the propeller engine

2019 ◽  
Vol 85 (12) ◽  
pp. 43-50
Author(s):  
D. A. Movenko ◽  
L. V. Morozova ◽  
S. V. Shurtakov
Keyword(s):  
Mechanical Properties ◽  
Chemical Composition ◽  
Yield Point ◽  
Protective Coating ◽  
Fracture Pattern ◽  
Corrosion Cracking ◽  
Tempered Martensite ◽  
Neck Formation ◽  
Static Mechanism ◽  
Shaft Surface

The results of studying operational destruction of a high-loaded cardan shaft of the propeller engine made of steel 38KhN3MFA are presented to elucidate the cause of damage and develop a set of recommendations and measures aimed at elimination of adverse factors. Methods of scanning electron and optical microscopy, as well as X-ray spectral microanalysis are used to determine the mechanical properties, chemical composition, microstructure, and fracture pattern of cardan shaft fragments. It is shown that the mechanical properties and chemical composition of the material correspond to the requirements of the regulatory documentation, defects of metallurgical origin both in the shaft metal and in the fractures are absent. The microstructure of the studied shaft fragments is tempered martensite. Fractographic analysis revealed that the destruction of cardan shaft occurred by a static mechanism. The fracture surface is coated with corrosion products. The revealed cracks developed by the mechanism of corrosion cracking due to violation of the protective coating on the shaft. The results of the study showed that the destruction of the cardan shaft of a propeller engine made of steel 38Kh3MFA occurred due to formation and development of spiral cracks by the mechanism of stress corrosion cracking under loads below the yield point of steel. The reason for «neck» formation upon destruction of the shaft fragment is attributed to the yield point of steel attained during operation. Regular preventive inspections are recommended to assess the safety of the protective coating on the shaft surface to exclude formation and development of corrosion cracks.

REPUBLIC 65

Alloy Digest ◽  
1960 ◽  
Vol 9 (5) ◽  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Tensile Properties ◽  
Yield Point ◽  
Precipitation Hardening ◽  
Heat Treating ◽  
Low Alloy Steel ◽  
Rolled Condition ◽  
Hardening Heat Treatment ◽  
Minimum Yield

Abstract REPUBLIC-65 is a precipitation hardenable low alloy steel which will meet 65000 psi minimum yield point in the as-rolled condition followed by a precipitation hardening heat treatment. This datasheet provides information on composition, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SA-98. Producer or source: Republic Steel Corporation.

DIFFRACTION ANALYSIS OF DEFORMED METALS: Theory, Methods, Programs

2019 ◽  
Author(s):  
Faina Satdarova
Keyword(s):  
Experimental Design ◽  
Dislocation Density ◽  
Mathematical Models ◽  
Diffraction Analysis ◽  
Experimental Research ◽  
Russian Federation ◽  
Statistical Estimation ◽  
X Rays ◽  
National University ◽  
The Russian Federation

General analysis of the distribution of crystals orientation and dislocation density in the polycrystalline system is presented. Recovered information in diffraction of X-rays adopting is new to structure states of polycrystal. Shear phase transformations in metals — at the macroscopic and microscopic levels — become a clear process. Visualizing the advances is produced by program included in package delivered. Mathematical models developing, experimental design, optimal statistical estimation, simulation the system under study and evolution process on loading serves as instrumentation. To reduce advanced methods to research and studies problem-oriented software will promote when installed. Automation programs passed a testing in the National University of Science and Technology “MISIS” (The Russian Federation, Moscow). You score an advantage in theoretical and experimental research in the field of physics of metals.

Low dislocation density AlN on sapphire prepared by double sputtering and annealing

2020 ◽  
Vol 13 (9) ◽  
pp. 095501
Author(s):  
Ding Wang ◽  
Kenjiro Uesugi ◽  
Shiyu Xiao ◽  
Kenji Norimatsu ◽  
Hideto Miyake
Keyword(s):  
Dislocation Density ◽  
Low Dislocation Density
Sign in / Sign up

Export Citation Format

Share Document