Integral methods for solving thermal conductivity problems and their application to evaluating heat exchange in certain gas-turbine elements

1980 ◽  
Vol 12 (7) ◽  
pp. 897-901 ◽  
Author(s):  
Yu. S. Vytchikov ◽  
V. M. Khorol'skii
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchange ◽  
Gas Turbine ◽  
Integral Methods

scholarly journals Field Test and Numerical Simulation on the Long-Term Thermal Response of PHC Energy Pile in Layered Foundation

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3873
Author(s):  
Guozhu Zhang ◽  
Ziming Cao ◽  
Yiping Liu ◽  
Jiawei Chen
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchange ◽  
Temperature Variation ◽  
Thermal Response ◽  
Ground Temperature ◽  
Short Term ◽  
Energy Pile ◽  
Backfill Soil ◽  
Short And Long Term

Investigation on the long-term thermal response of precast high-strength concrete (PHC) energy pile is relatively rare. This paper combines field experiments and numerical simulations to investigate the long-term thermal properties of a PHC energy pile in a layered foundation. The major findings obtained from the experimental and numerical studies are as follows: First, the thermophysical ground properties gradually produce an influence on the long-term temperature variation. For the soil layers with relatively higher thermal conductivity, the ground temperature near to the energy pile presents a slowly increasing trend, and the ground temperature response at a longer distance from the center of the PHC pile appears to be delayed. Second, the short- and long-term thermal performance of the PHC energy pile can be enhanced by increasing the thermal conductivity of backfill soil. When the thermal conductivities of backfill soil in the PHC pile increase from 1 to 4 W/(m K), the heat exchange amounts of energy pile can be enhanced by approximately 30%, 79%, 105%, and 122% at 1 day and 20%, 47%, 59%, and 66% at 90 days compared with the backfill water used in the site. However, the influence of specific heat capacity of the backfill soil in the PHC pile on the short-term or long-term thermal response can be ignored. Furthermore, the variation of the initial ground temperature is also an important factor to affect the short-and-long-term heat transfer capacity and ground temperature variation. Finally, the thermal conductivity of the ground has a significant effect on the long-term thermal response compared with the short-term condition, and the heat exchange rates rise by about 5% and 9% at 1 day and 21% and 37% at 90 days as the thermal conductivities of the ground increase by 0.5 and 1 W/(m K), respectively.

scholarly journals Experimental Study on the Heat Exchange Mechanism in a Simulated Self-Circulation Wellbore

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2918
Author(s):  
Liang Zhang ◽  
Songhe Geng ◽  
Jun Kang ◽  
Jiahao Chao ◽  
Linchao Yang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchange ◽  
Convective Heat Transfer Coefficient ◽  
Injection Rate ◽  
Circulation Rate ◽  
Similarity Analysis ◽  
Published Data ◽  
Outlet Temperature ◽  
Hot Dry Rocks ◽  
Mining Capacity

Self-circulation wellbore is a new technique for geothermal development in hot dry rocks (HDR), which uses a U-shape channel composed of tubing and casing as the heat exchanger. In this study, a self-circulation wellbore in HDR on a laboratory scale was built, and a serial of experiments were conducted to investigate the heat exchange law and the influencing factors on the heat mining rate of the wellbore. A similarity analysis was also made to estimate the heat-mining capacity of the wellbore on a field scale. The experimental results show that the large thermal conductivity and heat capacity of granite with high temperature can contribute to a large heat-mining rate. A high injection rate can cause a high convective heat transfer coefficient in wellbore, while a balance is needed between the heat mining rate and the outlet temperature. An inner tubing with low thermal conductivity can significantly reduce the heat loss to the casing annulus. The similarity analysis indicates that a heat mining rate of 1.25 MW can be reached when using a 2000 m long horizontal well section in a 150 °C HDR reservoir with a circulation rate of 602.8 m3/day. This result is well corresponding to the published data.

The Study of Thermal Properties and Micro Structures of YSZ

2007 ◽  
Author(s):  
S. M. Guo ◽  
M. B. Silva ◽  
Patrick F. Mensah ◽  
Nalini Uppu
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Gas Turbine ◽  
Bond Coat ◽  
Sintering Temperature ◽  
Heating Process ◽  
Thermal Barrier ◽  
Inlet Temperature ◽  
Low Thermal Conductivity ◽  
Gas Tight

Thermal barrier coatings (TBCs) are used in gas turbine engines to achieve a better efficiency by allowing increased turbine inlet temperature and decreasing the amount of cooling air used. Plasma spraying is one of the most reliable methods to produce TBCs, which are generally comprised of a top coating of ceramic and a bond-coat of metal. Usually, the top coating is Yttria-Stabilized-Zirconia (YSZ), providing the thermal barrier effect. The bond-coat is typically a layer of M-Cr-Al-Y (where “M” stands for “metal”), employed to improve the attachment between the ceramic top-coat and the substrate. Due to the extreme temperature gradient presented in the plasma jet and the wide particle size distribution, during the coating process, injected ceramic powders may experience a significantly different heating process. Different heating history, coupled with the substrate preheating temperature, may affect the thermal properties of the YSZ layers. In this paper, four sets of mol 8% YSZ disks are fabricated under controlled temperatures of 1100°C, 1200°C, 1400°C and 1600°C. Subsequently the thermal properties and the microstructures of these YSZ disks are studied. The results indicate a strong microstructure change at a temperature slightly below 1400°C. For a high sintering temperature, a dense YSZ layer can be formed, which is good for gas tight operation; At low sintering temperature, say 1200°C, a porous YSZ layer is formed, which has the advantage of low thermal conductivity. For gas turbine TBC applications, a robust low thermal conductivity YSZ layer is desirable, while for Solid Oxide Fuel Cells, a gas-tight YSZ film must be formed. This study offers a general guideline on how to prepare YSZ layers, mainly by controlling the heating process, to form microstructures with desired properties.

Conjugate Heat Transfer Simulations to Evaluate the Effect of Anisotropic Thermal Conductivity on Overall Cooling Effectiveness

2021 ◽  
pp. 1-26
Author(s):  
Carol E. Bryant ◽  
James L. Rutledge
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Gas Turbine ◽  
Conjugate Heat Transfer ◽  
Ceramic Matrix Composites ◽  
Conductivity Anisotropy ◽  
Cooling Effectiveness ◽  
External Cooling ◽  
Anisotropic Thermal Conductivity ◽  
Overall Effectiveness

Abstract Ceramic matrix composites (CMCs) show promise as higher temperature capable alternatives to traditional metallic components in gas turbine engine hot gas paths. However, CMC components will still require both internal and external cooling, such as film cooling. The overall cooling effectiveness is determined not only by the design of coolant flow, but also by the conduction through the materiel itself. CMCs have anisotropic thermal conductivity, giving rise to heat flow that differs somewhat relative to what we have come to expect from experience with traditional metallic components. Conjugate heat transfer computational fluid dynamics (CFD) simulations were performed in order to isolate the effect anisotropic thermal conductivity has on a cooling architecture consisting of both internal and external cooling. Results show the specific locations and unique effects of anisotropic thermal conduction on overall effectiveness. Thermal conductivity anisotropy is shown to have a significant effect on the resulting overall effectiveness. As CMCs begin to make their way into gas turbine engines, care must be taken to ensure that anisotropy is characterized properly and considered in the thermal analysis.

scholarly journals Analysis of the energetic/environmental performances of gas turbine plant: Effect of thermal barrier coatings and mass of cooling air

2009 ◽  
Vol 13 (1) ◽  
pp. 147-164 ◽  
Author(s):  
Ion Ion ◽  
Anibal Portinha ◽  
Jorge Martins ◽  
Vasco Teixeira ◽  
Joaquim Carneiro
Keyword(s):  
Thermal Conductivity ◽  
Gas Turbine ◽  
Thermal Barrier Coatings ◽  
Turbine Blades ◽  
Heat Transfer Analysis ◽  
Thermal Barrier ◽  
Inlet Temperature ◽  
Barrier Coatings ◽  
Cooling Air Flow ◽  
Cooling Air

Zirconia stabilized with 8 wt.% Y2O3 is the most common material to be applied in thermal barrier coatings owing to its excellent properties: low thermal conductivity, high toughness and thermal expansion coefficient as ceramic material. Calculation has been made to evaluate the gains of thermal barrier coatings applied on gas turbine blades. The study considers a top ceramic coating Zirconia stabilized with 8 wt.% Y2O3 on a NiCoCrAlY bond coat and Inconel 738LC as substrate. For different thickness and different cooling air flow rates, a thermodynamic analysis has been performed and pollutants emissions (CO, NOx) have been estimated to analyze the effect of rising the gas inlet temperature. The effect of thickness and thermal conductivity of top coating and the mass flow rate of cooling air have been analyzed. The model for heat transfer analysis gives the temperature reduction through the wall blade for the considered conditions and the results presented in this contribution are restricted to a two considered limits: (1) maximum allowable temperature for top layer (1200?C) and (2) for blade material (1000?C). The model can be used to analyze other materials that support higher temperatures helping in the development of new materials for thermal barrier coatings.

scholarly journals Improving the quality of alumina-containing sinter using water-cooled furnace shell

2012 ◽  
Vol 44 (3) ◽  
pp. 281-286
Author(s):  
A.V. Aleksandrov ◽  
V.V. Aleksandrov
Keyword(s):  
Thermal Conductivity ◽  
Steady State ◽  
Heat Exchange ◽  
Energy Balance ◽  
Cold Water ◽  
Sintering Temperature ◽  
Radiant Heat ◽  
Thermal Processes ◽  
Technical Solutions

This article deals with the use of computer modeling to develop technical solutions to ensure better quality of alumina-containing sinter. The simulation accounted for the influence of the feed materials on the thermal processes in the furnace. The energy balance (including thermal conductivity, heat convection and radiant heat exchange) was solved assuming steady state. A good correlation was observed for the actual and calculated temperatures of the solids and gases, with less than 15% discrepancy. Using the model of the furnace investigated the possibility of lowering the temperature of sintering by removing heat from the outside of the furnace shell. To reduce the sintering temperature to 1000 ?C length of the refractory lined steel is 5 m, the height of the lining should not exceed - 0.06 m, the required rate of cold water - 54.7 m3/h

scholarly journals Study on non-stationary heat exchange in combined packages of water-resistant protective clothing of firefighters

2020 ◽  
Vol 64 (4) ◽  
pp. 467-476
Author(s):  
A. I. Ol’shanskii ◽  
R. V. Okunev ◽  
A. M. Gusarov
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchange ◽  
Protective Clothing ◽  
Thermal Contact ◽  
Exchange Process ◽  
Toxic Substances ◽  
Nonlinear Transport ◽  
Stationary Heat ◽  
Technical Requirements ◽  
Linearization Methods

The results of research of non-stationary heat exchange in combined packages intended for creation of special water- and heat-resistant protective clothing of firefighters from dangerous and harmful factors during emergency rescue and other urgent works, with participation of non-toxic substances, acid solutions, alkalis, oil and petroleum products, liquid toxic substances, as well as during operation in water with temperature from 0 to 70 °С are presented. The stability of clothing material packs has been investigated as a transient heat exchange process in a multilayer plate with ideal thermal contact at the joints of the layers. The unlimited plate is heated on both sides under different heat exchange conditions according to Newton’s Law, with constant action of the heat source on one of the surfaces of the hot liquid contacting through the waterproof thin surface. Second surface of the plate interacts with external medium, temperature of which varies according to linear law. At solving the equation of non-stationary thermal conductivity with nonlinear transport coefficients, linearization methods are used based on the approximation of nonlinear coefficients, such that nonlinear equations become approximately linear. The entire heat transfer process is divided into a plurality of small-time intervals within which the transfer coefficients are constant. The zonal method of investigation of non-stationary thermal conductivity in clothing packages establishes equations for calculation of temperature, densities of thermal flows, distribution of temperature across thickness of clothing packages. It has been shown that under accepted calculation simplifications, parameter values are well consistent with the experiment. The composition of the clothing package is proposed, which meets the technical requirements of TУ BY 101114857.082-2015 “Personal Protective Kits”.

An Evaluation of the Application of Nanofluids in Intercooled Cycle Marine Gas Turbine Intercooler

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Ningbo Zhao ◽  
Xueyou Wen ◽  
Shuying Li
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Gas Turbine ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Inlet Temperature ◽  
Transfer Performance ◽  
Pumping Power ◽  
Flow And Heat Transfer ◽  
Overall Performance

Coolant is one of the important factors affecting the overall performance of the intercooler for the intercooled (IC) cycle marine gas turbine. Conventional coolants, such as water and ethylene glycol, have lower thermal conductivity which can hinder the development of highly effective compact intercooler. Nanofluids that consist of nanoparticles and base fluids have superior properties like extensively higher thermal conductivity and heat transfer performance compared to those of base fluids. This paper focuses on the application of two different water-based nanofluids containing aluminum oxide (Al2O3) and copper (Cu) nanoparticles in IC cycle marine gas turbine intercooler. The effectiveness-number of transfer unit method is used to evaluate the flow and heat transfer performance of intercooler, and the thermophysical properties of nanofluids are obtained from literature. Then, the effects of some important parameters, such as nanoparticle volume concentration, coolant Reynolds number, coolant inlet temperature, and gas side operating parameters on the flow and heat transfer performance of intercooler, are discussed in detail. The results demonstrate that nanofluids have excellent heat transfer performance and need lower pumping power in comparison with base fluids under different gas turbine operating conditions. Under the same heat transfer, Cu–water nanofluids can reduce more pumping power than Al2O3–water nanofluids. It is also concluded that the overall performance of intercooler can be enhanced when increasing the nanoparticle volume concentration and coolant Reynolds number and decreasing the coolant inlet temperature.

Sign in / Sign up

Export Citation Format

Share Document