Processes of precipitation and intercrystalline corrosion in high-nitrogen Cr-Mn steels after isothermal annealing

1981 ◽  
Vol 23 (5) ◽  
pp. 310-313 ◽  
Author(s):  
Ts. V. Rashev ◽  
L. P. Dzhambazova ◽  
R. St. Kovacheva ◽  
Ch. A. Andreev
Keyword(s):  
Isothermal Annealing ◽  
Intercrystalline Corrosion ◽  
High Nitrogen

AEM analysis of crystallization in Ti-based amorphous alloys

1983 ◽  
Vol 41 ◽  
pp. 270-271
Author(s):  
A.R. Pelton ◽  
A.F. Marshall ◽  
Y.S. Lee
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Amorphous Materials ◽  
Isothermal Annealing ◽  
Amorphous Matrix ◽  
Nucleation And Growth ◽  
Current Interest ◽  
Amorphous Films ◽  
Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

TEM Analysis of Long-Period Polytypes in SiC—S

1976 ◽  
Vol 34 ◽  
pp. 630-631
Author(s):  
S. Shinozaki ◽  
J. W. Sprys
Keyword(s):  
Electron Diffraction ◽  
Isothermal Annealing ◽  
Tem Analysis ◽  
Long Period ◽  
Transmission Electron ◽  
Average Grain Size ◽  
High Resolution Tem ◽  
Structural Lattice ◽  
The Stability ◽  
Continuous Curves

In reaction sintered SiC (∽ 5um average grain size), about 15% of the grains were found to have long-period structures, which were identifiable by transmission electron microscopy (TEM). In order to investigate the stability of the long-period polytypes at high temperature, crystal structures as well as microstructural changes in the long-period polytypes were analyzed as a function of time in isothermal annealing.Each polytype was analyzed by two methods: (1) Electron diffraction, and (2) Electron micrograph analysis. Fig. 1 shows microdensitometer traces of ED patterns (continuous curves) and calculated intensities (vertical lines) along 10.l row for 6H and 84R (Ramsdell notation). Intensity distributions were calculated based on the Zhdanov notation of (33) for 6H and [ (33)3 (32)2 ]3 for 84R. Because of the dynamical effect in electron diffraction, the observed intensities do not exactly coincide with those intensities obtained by structure factor calculations. Fig. 2 shows the high resolution TEM micrographs, where the striped patterns correspond to direct resolution of the structural lattice periodicities of 6H and 84R structures and the spacings shown in the figures are as expected for those structures.

EFFECT OF ISOTHERMAL ANNEALING ON THE STRUCTURE OF AN AMORPHOUS Pd-Si ALLOY

1982 ◽  
Vol 43 (C9) ◽  
pp. C9-83-C9-86
Author(s):  
M. Laridjani ◽  
J. F. Sadoc
Keyword(s):  
Isothermal Annealing

Poultry Manure as a Fertilizer

EDIS ◽  
2013 ◽  
Vol 2013 (11) ◽  
Author(s):  
Michael A. Davis ◽  
Doug R. Sloan ◽  
Gerald Kidder ◽  
R. D. Jacobs
Keyword(s):  
Organic Matter ◽  
Environmental Factors ◽  
Nitrogen Content ◽  
Soil Amendment ◽  
Poultry Manure ◽  
Nutrient Retention ◽  
High Nitrogen Content ◽  
High Nitrogen ◽  
Animal Science ◽  
Fact Sheet

Animal manures have been used as natural crop fertilizers for centuries. Because of poultry manure’s high nitrogen content, it has long been recognized as one of the most desirable manures. Besides fertilizing crops, manures also supply other essential plant nutrients and serve as a soil amendment by adding organic matter, which helps improve the soil’s moisture and nutrient retention. Organic matter persistence will vary with temperature, drainage, rainfall, and other environmental factors. This 2-page fact sheet was written by Michael A. Davis, D.R. Sloan, Gerald Kidder, and R.D. Jacobs, and published by the UF Department of Animal Science, November 2013. http://edis.ifas.ufl.edu/aa205

DECOMPOSITION AND PERFORMANCEOFNEW HIGH NITROGEN PROPELLANTS AND EXPLOSIVES

2007 ◽  
Vol 6 (2) ◽  
pp. 255-268
Author(s):  
Bryce C. Tappan ◽  
Steven F. Son ◽  
Arif N. Ali ◽  
David E. Chavez ◽  
Michael A. Hiskey
Keyword(s):  
High Nitrogen

NIROSTA 4429

Alloy Digest ◽  
2000 ◽  
Vol 49 (5) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Pitting Corrosion ◽  
Intergranular Corrosion ◽  
Heat Treating ◽  
Low Carbon ◽  
High Nitrogen ◽  
Temperature Performance ◽  
Pitting Corrosion Resistance

Abstract Nirosta 4429 is a low-carbon, high-nitrogen version of type 316 stainless steel. The low carbon imparts intergranular corrosion resistance while the nitrogen imparts both higher strength and some increased pitting corrosion resistance. It is recommended for use as welded parts that need not or cannot be annealed after welding. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-787. Producer or source: ThyssenKrupp Nirosta.

Sign in / Sign up

Export Citation Format

Share Document