Morphological evolution of polypropylene/polystyrene blends in a twin-screw extruder

2010 ◽  
Vol 119 (4) ◽  
pp. 1970-1977 ◽  
Author(s):  
Yang Wu ◽  
Shaowei Jing ◽  
Qun Gu ◽  
Binyao Li
Keyword(s):  
Morphological Evolution ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Twin Screw

Reactive Blending in a Twin Screw Extruder

1996 ◽  
Vol 11 (2) ◽  
pp. 139-146 ◽  
Author(s):  
A. De Loor ◽  
P. Cassagnau ◽  
A. Michel ◽  
L. Delamare ◽  
B. Vergnes
Keyword(s):  
Twin Screw Extruder ◽  
Reactive Blending ◽  
Screw Extruder ◽  
Twin Screw

SME-Arrhenius Model for WSI of Rice Flour in a Twin-Screw Extruder

2005 ◽  
Vol 82 (5) ◽  
pp. 574-581 ◽  
Author(s):  
Hanwu Lei ◽  
R. Gary Fulcher ◽  
Roger Ruan ◽  
Bernhard van Lengerich
Keyword(s):  
Rice Flour ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Arrhenius Model ◽  
Twin Screw

scholarly journals Effects of a Twin-Screw Extruder Equipped with a Molten Resin Reservoir on the Mechanical Properties and Microstructure of Recycled Waste Plastic Polyethylene Pellet Moldings

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1058
Author(s):  
Hikaru Okubo ◽  
Haruka Kaneyasu ◽  
Tetsuya Kimura ◽  
Patchiya Phanthong ◽  
Shigeru Yao
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Value Added ◽  
Industrial Applications ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Polymer Properties ◽  
Wide Range ◽  
Twin Screw ◽  
Recycled Plastics

Each year, increasing amounts of plastic waste are generated, causing environmental pollution and resource loss. Recycling is a solution, but recycled plastics often have inferior mechanical properties to virgin plastics. However, studies have shown that holding polymers in the melt state before extrusion can restore the mechanical properties; thus, we propose a twin-screw extruder with a molten resin reservoir (MSR), a cavity between the screw zone and twin-screw extruder discharge, which retains molten polymer after mixing in the twin-screw zone, thus influencing the polymer properties. Re-extruded recycled polyethylene (RPE) pellets were produced, and the tensile properties and microstructure of virgin polyethylene (PE), unextruded RPE, and re-extruded RPE moldings prepared with and without the MSR were evaluated. Crucially, the elongation at break of the MSR-extruded RPE molding was seven times higher than that of the original RPE molding, and the Young’s modulus of the MSR-extruded RPE molding was comparable to that of the virgin PE molding. Both the MSR-extruded RPE and virgin PE moldings contained similar striped lamellae. Thus, MSR re-extrusion improved the mechanical performance of recycled polymers by optimizing the microstructure. The use of MSRs will facilitate the reuse of waste plastics as value-added materials having a wide range of industrial applications.

Sign in / Sign up

Export Citation Format

Share Document