A nonlinear concrete damaged plasticity model for simulation reinforced concrete structures using ABAQUS

The reinforced concrete structure is typical and widely used in many fields. The behavior of concrete is nonlinear and complex. Especially, when cracks/crushings occurred in softening phase. Thus, It is important to find a damaged model of concrete with high reliability in the numerical simulation. The nonlinear behavior of concrete is the most feature used in the simulation. This characteristic is expressed through the parameters defining the yield surface, the flow potential, and the nonlinear relationship of stress-strain in the cases of tension and compression. This paper introduces a damaged concrete model that applies to the simulation of reinforced concrete structures. The reinforced concrete beam and flat slab are selected as examples to evaluate the reliability of the model presented. Through the results achieved, the model used in this paper shows high reliability and can be used to simulate more complex reinforced concrete structures.

Modified Numerical Modeling of Axially Loaded Concrete-Filled Steel Circular-Tube Columns

Predicting the behavior of concrete in a Concrete-Filled Steel Tubular (CFST) column is challenging due to the sensitivity to input parameters such as the size of the cross-section, the material modeling, and the boundary conditions. The present paper proposes a new modified finite element model to predict the behavior and strength of a CFST subjected to axial compression. The development is based on the concrete damaged plasticity model, with its stress-strain relationship revised from the available model. The predicted accuracy of the modified model is verified via a wide range of experimental tests. The proposed model has more accuracy than the available models in predicting the ultimate compression strength. The results show good agreement with the test data, allowing its use in modeling CFST columns.

The Mechanical Properties and Damage Evolution of UHPC Reinforced with Glass Fibers and High-Performance Polypropylene Fibers

Due to the sharp and corrosion-prone features of steel fibers, there is a demand for ultra-high-performance concrete (UHPC) reinforced with nonmetallic fibers. In this paper, glass fiber (GF) and the high-performance polypropylene (HPP) fiber were selected to prepare UHPC, and the effects of different fibers on the compressive, tensile and bending properties of UHPC were investigated, experimentally and numerically. Then, the damage evolution of UHPC was further studied numerically, adopting the concrete damaged plasticity (CDP) model. The difference between the simulation values and experimental values was within 5.0%, verifying the reliability of the numerical model. The results indicate that 2.0% fiber content in UHPC provides better mechanical properties. In addition, the glass fiber was more significant in strengthening the effect. Compared with HPP-UHPC, the compressive, tensile and flexural strength of GF-UHPC increased by about 20%, 30% and 40%, respectively. However, the flexural toughness indexes I5, I10 and I20 of HPP-UHPC were about 1.2, 2.0 and 3.8 times those of GF-UHPC, respectively, showing that the toughening effect of the HPP fiber is better.

Numerical Simulation of the Mechanical Behavior of Fiber-Reinforced Cement Composites Subjected Dynamic Loading

The problem of damage accumulation in fiber-reinforced concrete to structures supporting underground workings and tunnel linings against dynamic loading is insufficiently studied. The mechanical properties were determined and the mechanism of destruction of fiber-reinforced concrete with different reinforcement parameters is described. The parameters of the Concrete Damaged Plasticity model for fiber-reinforced concrete at different reinforcement properties are based on the results of lab experiments. Numerical simulation of the composite concrete was performed in the Simulia Abaqus software package (Dassault Systemes, Vélizy-Villacoublay, France). Modeling of tunnel lining based on fiber-reinforced concrete was performed under seismic loading.

Calibration of Concrete Damaged Plasticity Model parameters for shear walls

ABSTRACT Reinforced concrete structures are relatively complex to analyze, with nonlinear effects like cracking, crushing, steel yielding, aggregate interlock, dowel effect, concrete-rebar interaction and so on. The concrete damaged plasticity CDP model is a consolidated smeared-crack model which accounts for multiaxial behavior with good agreement to experimental results. One particular relevant application which benefits greatly from such feature is the shear wall, as shear stress significantly influences its overall behavior, therefore multiaxial constitutive models and three-dimensional finite elements usage consist in a fitting modeling approach. Reinforced concrete shear walls are structures especially useful for lateral force-resisting systems, as they provide ductility, stiffness and strength. Albeit CDP is widely applied, its parameters are not consensus in the literature, which represents a relevant research gap. The present work considers and compares CDP parameters from relevant literature, in order to calibrate those parameters for the case of reinforced concrete shear walls. To this purpose, four wall experiments related in the bibliography are modeled using solid finite elements for concrete and trusses for rebars using commercial package ABAQUS. All walls are flexure-controlled with aspect ratio greater than 2.0. By varying those parameters and comparing obtained force vs. displacement curves and interesting values attained, like yield lateral force and displacement, stiffness and maximum lateral force, it is settled a set of parameters with acceptable response focusing in the post-peak response based on the lower estimated error of displacement capacity. Those parameters agree reasonably with literature, although it is possible that obtained calibration is restricted to flexure controlled shear walls scope. It is possible that usage of trusses to represent reinforcement does not consider dowel effect, so a suggestion for future studies is to change trusses for elements with transverse stiffness, like beams or solids.

Selected Concrete Models Studied Using Willam’s Test

Willam’s test is a quick numerical benchmark in tension–shear regime, which can be used to verify inelastic (quasi-brittle) material models at the point level. Its sequence consists of two separate steps: uniaxial tension accompanied with contraction—until the tensile strength is attained; and next for softening (cracking) of the material—tension in two directions together with shear. A rotation of axes of principal strains and principal stresses is provoked in the second stage. That kind of process occurs during the analysis of real concrete structures, so a correct response of the material model at the point level is needed. Some familiar concrete models are selected to perform Willam’s test in the paper: concrete damaged plasticity and concrete smeared cracking—distributed in the commercial ABAQUS software, scalar damage with coupling to plasticity and isotropic damage—both implemented in the FEAP package. After a brief review of the theory, computations for each model are discussed. Passing or failing Willam’s test by the above models is concluded based on their results, indicating restrictions of their use for finite element computations of concrete structures with predominant mixed-mode fracture.