Calibration of Load and Resistance Factors for Breakwater Foundation Design. Application on Different Types of Superstructures

Load and resistance factor design is an efficient design approach that provides a system of consistent design solutions. This study aims to determine the load and resistance factors needed for the design of breakwater foundations within a probabilistic framework. In the study, four typical types of Korean breakwaters, namely, rubble mound breakwaters, vertical composite caisson breakwaters, perforated caisson breakwaters, and horizontal composite breakwaters, are investigated. The bearing capacity of breakwater foundations under wave loading conditions is thoroughly examined. Two levels of the target reliability index (RI) of 2.5 and 3.0 are selected to implement the load and resistance factors calibration using Monte Carlo simulations with 100,000 cycles. The normalized resistance factors are found to be lower for the higher target RI as expected. Their ranges are from 0.668 to 0.687 for the target RI of 2.5 and from 0.576 to 0.634 for the target RI of 3.0.

Investigation on the Reflection Coefficient for Seawalls Protected by a Rubble Mound Structure

Sea wave reflection from coastal protection structures is one of the main issues in the coastal design process. Several empirical formulas have been proposed so far to predict reflection coefficient from rubble mound breakwaters and smooth slopes. The aim of this study is to investigate wave reflection from a rubble mound structure placed in front of a vertical concrete seawall. Several experimental tests were performed on a two-dimensional wave flume by reproducing on a rubble mound structure with a steep single primary layer armored with a novel artificial unit. A new approach for the prediction of the reflection coefficient based on dimensional analysis is also proposed, and a new empirical equation is derived. The performance of the proposed equation was compared with widespread existing formulas, and a good accuracy was found.

Revisiting statistical properties of surf parameter with characteristic wave parameters for single random waves including spectral bandwidth effects

Results from a comparative study of the joint distribution of surf parameter and wave period are provided. First, two transformed joint distributions of wave height and wave period are compared. One of the distributions is a parametric model originating from a best fit to relatively broad-band field data covering a wide range of wave conditions, whilst the other distribution is theoretically based. It appears that the theoretically based distribution does not represent the features of the parametric model especially well, suggesting that parametric models should be used to describe relatively broad-banded data. Then, the theoretically based joint distribution of wave height and wave period is transformed to the joint distributions of surf parameter with wave height and wave period and it is demonstrated how these distributions are affected by the spectral bandwidth. Finally, the theoretically based distribution of wave height and wave period is also transformed to the joint distribution of wave runup time and wave period due to its relation to the stability of rubble-mound breakwaters. Comparisons are made with a limited set of data representing results from small-scale laboratory experiments related to stability of rubble-mound breakwaters. The agreement between measurements and predictions of the distribution of the surf parameter is fair, whilst the agreement is poorer for the probability of resonance.

Numerical Model Study of Prototype Drop Tests on Cube and Cubipod® Concrete Armor Units Using the Combined Finite–Discrete Element Method

This paper aims to evaluate the structural strength of unreinforced concrete armor units (CAU), named Cubipod®, used on rubble-mound breakwaters and coastal structures, through a numerical methodology using the combined finite–discrete element method (FDEM). A numerical modeling methodology is developed to reproduce the results of an experimental examination published by Medina et al. (2011) of a free-fall drop test performed on a 15 t conventional Cubic block and a 16 t Cubipod® unit. The field results of the Cube drop tests were used to calibrate the model. The numerically simulated response to the Cubipod® test is then discussed in the context of a validation study. The calibration process and validation study provide insights into the sensitivity of breakage to tensile strength and collision angle, as well as a better understanding of the crushing and cracking damage of this unit under drop test impact conditions.

Wave RUN-UP Measurements under very oblique wave incidence

Under the scope of the HYDRALAB+ transnational access project, the so-called RODBreak experiment was conducted in the multidirectional wave basin at the Marienwerden facilities of the Leibniz University Hannover (LUH). A stretch of a rubble-mound breakwater was built in the wave basin with a very gentle slope. Its armour layer was made of Antifer cubes, at the roundhead and adjoining trunk, and of rock, at the rest of the trunk. A set of tests was carried out to extend the range of wave steepness values analysed in wave run-up, overtopping and armour layer stability studies, focusing on oblique extreme wave conditions, with incident wave angles from 40º to 90º. The present study focuses on the analysis of measured wave run-up values obtained in the tests and on their on their variability as well as the influence of the wave obliquity and directional spreading. Keywords: rubble-mound breakwaters; run-up; oblique waves; physical modelling; RODbreak.

STUDY OF RAPID SEDIMENTATION AT PARESAR INTAKE BASIN, CASPIAN SEA, DUE TO LARGE WRACK PARTICLES AND WIND-INDUCED CURRENTS

The rapid sedimentation at the entrance of Paresar intake basin is studied, in which unnatural wrack accumulation at the coast, combined with the existing sand, resulted in a major increase in the actual Longshore Sediment Transport (LST) rate. Considering the volume of updrift fillet at the northwest of main breakwater and the estimated LST rate, the advancement of updrift shoreline was highly unexpected. Sands and vegetative wracks were observed only 3 years after constructing the rubble mound breakwaters, resulting in water depth decrease at the entrance. Employing field measurements and numerical modeling, it is revealed that general wind-induced currents in Caspian Sea, which were ignored in the design, have a small effect on increasing LST rate. The unusual sedimentation can be mainly related to the high percentage of wrack particles at updrift coast.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/UNNnjDHL41k

STABILITY OF HIGH DENSITY CUBES IN RUBBLE MOUND BREAKWATERS

The stability number for rubble mound breakwaters is a function of several parameters and depends on unit shape, placing method, slope angle, relative density, etc. In this study two different densities for cubes in breakwater armour layers were tested to determine the influence of the density on the stability. The experimental results show that the stability of high density blocks were found to be more stable and the damage initiation for high density blocks started at higher stability numbers compared to normal density cubes.

ROUGHNESS FACTOR FOR MULTI-LAYER ARMOUR AS OVERTOPPING ESTIMATOR

Nowadays one of the most challenging problem for engineers is to adapt existing coastal structures to climate changes. Wave overtopping is highly sensitive to the increasing extreme water depths due to higher storm surges coupled with sea level rise. One way to face these problems for rubble mound breakwaters is to add one or more layers to the existing armour. Prediction of wave overtopping of coastal structures is presently obtained from empirical formulae in EurOtop (2018). For the case of overtopping over multi-layer armour, no validated method exists, so prediction must be based upon assumptions and judgement, with related uncertainties. This study is focused on the effects of different types of armour, the number of layer and other structural characteristics on the roughness factor f. The main effects of porosity and roughness will be investigated. This paper analyzes the results of several new physical model tests of different rubble mound breakwaters reproduced at the new medium scale random wave flume of the Department of Engineering of Roma Tre University.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/8cOdqkqQ-9s