sheet steels
Recently Published Documents


TOTAL DOCUMENTS

407
(FIVE YEARS 11)

H-INDEX

32
(FIVE YEARS 0)

2021 ◽  
Vol 168 ◽  
pp. 108281
Author(s):  
Xiaolei Xue ◽  
Shentong Lin ◽  
Zhan Guo ◽  
Yang Zhao ◽  
Quan Lin ◽  
...  

2021 ◽  
Vol 8 ◽  
Author(s):  
Nghiem NguyenVan ◽  
Kengo Kato ◽  
Hideki Ono

Medium Manganese Transformation Induced Plastic (Mn-TRIP) steels are expected to be a new generation of advanced high strength sheet steels due to their excellent balance between material cost and mechanical properties. During the solidification process, AlN precipitates at the grain boundary, which leads to the serious deterioration of hot ductility. However, the precipitation of AlN in Mn-TRIP steel has not been clear. In this study, the chemical compositions, morphology, size distribution, and the precipitation behavior of AlN inclusion in an Fe-0.5Al-2.0Mn alloy were studied under the continuous unidirectional solidification process. The results show that there are two types of nitride inclusions in the Fe-0.5Al-2.0Mn alloy: AlN inclusion and complex inclusion of Al2O3-AlN. The planar sections of most AlN particles are hexagonal. Based on the thermodynamic calculation, it was found that the content of Al has a large effect on the stability of Al2O3 and AlN. When the content of Al increases, the molten iron can be changed from saturated by Al2O3 to saturated by AlN. During the solidification process, the precipitation of Al2O3 inclusions occurred at the beginning of the solidification process. The precipitation of AlN inclusions occurred when the contents of Al and N exceeded the equilibrium value and grew until the end of the solidification. The precipitation conditions of AlN inclusion in the Fe-0.5Al-2.0Mn alloy during the solidification process were discussed. The precipitation and the amount of precipitate of AlN inclusions depend on the initial contents of Al, N, and O. It was found that the precipitation of AlN inclusions can be controlled by reducing the initial content of N to less than 0.0072 mass%.


2021 ◽  
Vol 147 (3) ◽  
pp. 04020361
Author(s):  
An Nhien Truong ◽  
Cao Hung Pham ◽  
Gregory J. Hancock
Keyword(s):  

2021 ◽  
Vol 802 ◽  
pp. 140631
Author(s):  
D. Frómeta ◽  
N. Cuadrado ◽  
J. Rehrl ◽  
C. Suppan ◽  
T. Dieudonné ◽  
...  

2021 ◽  
Vol 1016 ◽  
pp. 429-434
Author(s):  
Eman El-Shenawy ◽  
Hoda Refaiy ◽  
Hoda Nasr El-Din

Multiphase steels consisting of retained austenite and martensite/bainite microstructures such as TRIP, low-temperature-bainite, and Q&P steels are attractive candidates for the new-generation of AHSS. These steels exhibit a remarkable combination of strength and toughness which is essential to meet the objective of weight reduction of engineering-components, while maintaining the compromise of tough-safety requirements. Such good mechanical properties are due to the enhanced work hardening rate caused by austenite-to-martensite transformation during deformation and the strengthening contribution of martensite/bainite. The retained austenite can thermally decompose into more thermodynamically stable phases as a consequence of temperature changes, which is referred to as the thermal stability of retained austenite. TRIP-aided steel is an effective candidate for automotive parts because of safety and weight reduction requirements. The strength–ductility balance of high strength steel sheets can be remarkably improved by using transformation induced plasticity behavior of retained austenite. In manufacturing hot rolled TRIP-aided sheet steels, austenite transforms into bainite during the coiling process. Because black hot coils cool slowly after the coiling process, they are exposed at about 350–450°C for a few hours or days. Therefore, the metastable residual austenite can be decomposed into other phases. This decomposition of residual austenite can produce serious deteriorate of mechanical properties in hot rolled TRIP-aided sheet steels. The present work identified the decomposition behavior and study the thermal stability of retained austenite in the TRIP-aided steel with bainitic/ferrite matrix depending on coiling temperatures and holding times by means of DSC and XRD analysis.


2021 ◽  
Vol 1016 ◽  
pp. 946-951
Author(s):  
Mateusz Morawiec ◽  
Adam Grajcar

The paper presents microstructural and mechanical results of medium manganese steel deformed under high strain rates. The rotary hammer tests at strain rates of 250, 500 and 1000 s-1 were applied. Mechanical properties under dynamic tensile loads were determined. According to the obtained results, when strain rate increased the yield point of the steel increased. An opposite trend was present regarding total elongation. In case of tensile strength, its level is similar for all analyzed deformation rates. The microstructure of the steel after the dynamic tensile test is composed of bainite, martensite and martensitic-austenitic islands. The strain-induced martensitic transformation was identified in microscopic investigations.


2021 ◽  
Vol 1016 ◽  
pp. 132-136
Author(s):  
Adam Grajcar ◽  
Skowronek Adam ◽  
Mateusz Morawiec

The study aims at reviewing manufacturing schedules for hot-rolled and intercritically-annealed and thermomechanically processed medium-Mn sheet steels. Major differences between these two types of processing are indicated. They include initial microstructure (low-C martensite for hot-rolled products and deformed austenite for thermomechanically processed products), partitioning of alloying elements (depending on intercritical annealing or batch annealing conditions) and microstructure prior to cooling (ultrafine-grained lath mixture of ferrite and austenite for hot-rolled, intercritically annealed products and deformed austenite for directly cooled products). The comparison of typical microstructures (LM, SEM) and phase transformation behavior are presented. A role of Mn as an austenite stabilizer in a range used for medium-Mn steels is explained. Some results are provided for economic steels containing 3% and 5% Mn.


Sign in / Sign up

Export Citation Format

Share Document