Effect of Al2O3 nanoparticles on the mechanical behaviour of aluminium-based metal matrix composite synthesized via powder metallurgy

The effects of variation in aluminium oxide nanoparticles in aluminium-based metal matrix composite on the compressive and sliding wear deformation have been investigated. The compressive and sliding wear resistance of the composite increase significantly with the addition of nanoparticles in the matrix. The 5% aluminium oxide nanoparticles in the composite were found to be the optimal weight fraction of added nanoparticles that produced higher static yield strength, hardness, scratch resistance and lower material loss in wear in the composite. The addition of nanoparticles, beyond 5% weight fraction, in the matrix showed adverse effects in the performance of the composite due to its higher brittleness. The effects on wear properties of the composite with added nanoparticles beyond optimal weight fraction were more detrimental than those with lower weight fraction of nanoparticles.

Synthesis and Characterizations of Cadmium Doped Aluminium Oxide Nanoparticles

The cadmium doped aluminium oxide (CdAl2O3) nanoparticles were prepared by reverse precipitation method. The prepared CdAl2O3 nanoparticles were characterized by Powder X-Ray Diffraction in order to confirm the crystalline nature of the sample and found average crystallite size in the range 27.6 nm. Fourier transform infrared spectroscopy confirms the presence of metal oxygen bonds in the CdAl2O3 nanoparticle.

Impact of Solvents, Magnesium Oxide and Aluminium Oxide Nanoparticles on the Photophysical Properties of Acridine Orange Dye

Absorption and fluorescence spectroscopy techniques were applied to investigate the photophysical characteristics of acridine orange (AO) dye in solvents that included distilled water, dimethyl sulfoxide (DMSO), acetone and ethanol in various concentrations (1×10-4–1×10-6) M. All of the samples were served at room temperature. The relationships between various parameters describing the strength of optical transitions in atoms and molecules were reviewed. This study expresses various viewpoints by describing how concentration and solvent affect the dye's absorption and fluorescence spectra. The absorption spectra of AO exhibit a band at (490 nm), except for DMSO, which shifts more towards red by 5 nm. The fluorescence spectra show a blue shift in AO aqueous solution around 6 nm until (0.5×10-4) M, followed by a red shift at around 7 nm at (1×10-6) M. There is a blue shift in (1×10-5) M for DMSO at around 4 nm, then a 10 nm red shift in higher concentrations as well as a 9 nm red shift in acetone and 6 nm in ethanol. Adding magnesium oxide nanoparticles (MgO NPs) quenched AO in both absorption and fluorescence spectra, whereas maximum fluorescence and intensity increased when aluminium oxide nanoparticles (Al2O3 NPs) were added to the solution. KEYWORDS Laser dye, absorption spectrum, fluorescence spectrum, MgO NPs, Al2O3 NPs

Comparison of Flexural Strength and Surface Hardness of Polymethyl Methacrylate Resin Reinforced with Silanised Aluminium Oxide Nanoparticles- An In-vitro Study

Introduction: In complete denture fabrication, the common denture base material used is heat activated Polymethyl Methacrylate (PMMA). Considering various advantages, still there are some disadvantages like poor flexural strength and poor wear resistance. The flexural strength of any material reflects its potential to resist catastrophic fracture under a flexural load. Another property that influences the surface characteristics of acrylic resins is the surface hardness, which indicates the ease of finishing a material and its resistance to in-service scratching during cleaning procedures and exposure to various oral fluids. Thus an ideal denture base material should exhibit greater flexural strength and high surface hardness for the longevity of the dentures. Aim: To evaluate the effects of adding different percentages of silanised aluminium oxide (Al2O3) nanoparticles on the flexural strength and surface hardness of a conventional heat-polymerised acrylic resin. Materials and Methods: The in-vitro experimental study was conducted between October 2020 to Janaury 2021 at Drs. Sudha and Nageswara Rao Siddhartha Institute of Dental Sciences, Vijayawada, Andhra Pradesh, India. A total of 120 samples were fabricated and were grouped into four groups coded A to D (n=30). Group A was the control group (without adding Al2O3). Specimens in the other three groups (B to D) were reinforced with silanised Al2O3 at loadings of 1%, 2.5% and 5% w/w. Flexural strength was assessed with a three-point bending test using a universal testing machine. Surface hardness test was conducted using a Vickers Hardness (VH) tester. Data was analysed using Analysis of Variance (ANOVA) and Tukey’s post-hoc test. Results: Among all the reinforced groups highest flexural strength value was seen in Group C- PMMA+2.5% w/w silanised aluminium oxide nanoparticles reinforced group (88.33 Mpa) and highest surface hardness value was seen in the Group D- PMMA+5% w/w silanised Aluminium oxide nanoparticles reinforced group (29.44 VH). Conclusion: Reinforcement of the conventional heat cured acrylic resin with 2.5% w/w silanised Al2O3 nanoparticles significantly increased its flexural strength and hardness.