FEATURES OF THE STRAIN-STRESS STATE OF BEAMS WITH A CORRUGATED WALL OF VARIABLE RIGIDITY

Corrugated steel beams represent a promising area of research in the fi eld of structural engineering today. The article studies the behavior of a metal beam with a corrugated wall of an I-profi le under bending conditions. Beam considered span of 12 m. A fi nite element model of the calculated structure was built in the LIRA-SAPR software package. The analysis of the stress-strain state of a corrugated beam of variable stiff ness, which has a fl at fragment in the central part of the wall, is carried out. The beam thus obtained has a number of advantages over beams with only a fl at or fully corrugated wall. The conclusions based on the results of the analysis of the calculation are presented.

Thin-film Rayleigh–Taylor instability in the presence of a deep periodic corrugated wall

Rayleigh–Taylor instability of a thin liquid film overlying a passive fluid is examined when the film is attached to a periodic wavy deep corrugated wall. A reduced-order long-wave model shows that the wavy wall enhances the instability toward rupture when the interface pattern is sub-harmonic to the wall pattern. An expression that approximates the growth constant of instability is obtained for any value of wall amplitude for the special case when the wall consists of two full waves and the interface consists of a full wave. Nonlinear computations of the interface evolution show that sliding is arrested by the wavy wall if a single liquid film residing over a passive fluid is considered but not necessarily when a bilayer sandwiched by a top wavy wall and bottom flat wall is considered. In the latter case interface tracking shows that primary and secondary troughs will evolve and subsequently slide along the flat wall due to symmetry-breaking. It is further shown that this sliding motion of the interface can ultimately be arrested by the top wavy wall, depending on the holdup of the fluids. In other words, there exists a critical value of the interface position beyond which the onset of the sliding motion is observed and below which the sliding is always arrested.

Thermal effect of a fire on a steel beam with corrugated wall with fireproof mineral-wool cladding

This paper reports a study into the possibility of applying a simplified approach, recommended by standards for conventional steel beams, to determine the heating temperature under the conditions of a fire in relation to steel I-beams with a corrugated wall. The research is predetermined by the limitation of methods that make it possible to determine the heating temperature of this type of beam in a fire using engineering methods with a small amount of calculations. Technical data on steel beams with cladding have been considered for calculation, the features of heat impact of fire on them have been analyzed, a calculation procedure has been devised, the estimation schemes have been built, and the calculations have been performed. Data on the temperature distribution in the cross-sections of beams with and without cladding were obtained by using a simplified method recommended by standards and the refined method based on a finite-element method. Mathematical models have been constructed for calculations that describe the effect of a standard temperature regime of fire on the distribution of temperature in each minute in the cross-sections of steel beams with and without cladding. The models have been described on the basis of the differential equation of thermal conductivity, boundary conditions of the third kind, which take into consideration convective and radiant heat transfer. It was established that the mineral wool cladding of the beam with a corrugated wall is a reliable fire protection agent. The heating temperature of the beam does not reach a critical value of 500 °C in 60 minutes, which provides the class of this beam with the most stringent requirements for its fire resistance in accordance with the classification in line with the acting norms in Ukraine. The simplified method, recommended by the current standards of the European Union and Ukraine, could be effectively used to analyze the fire resistance of these beams and is the basis of the procedure for the estimated assessment of the fire resistance of these structures

Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique

The paper examines effectiveness of the vibration correlation technique which allows determining the buckling or limit loads by means of measured natural frequencies of structures. A steel silo segment with a corrugated wall, stiffened with cold-formed channel section columns was analysed. The investigations included numerical analyses of: linear buckling, dynamic eigenvalue and geometrically static non-linear problems. Both perfect and imperfect geometries were considered. Initial geometrical imperfections included first and second buckling and vibration mode shapes with three amplitudes. The vibration correlation technique proved to be useful in estimating limit or buckling loads. It was very efficient in the case of small and medium imperfection magnitudes. The significant deviations between the predicted and calculated buckling and limit loads occurred when large imperfections were considered.

Effect of geometrical variations on the structural performance of shipping container panels: A parametric study towards a new alternative design

In the field of logistics, containers are indispensable for shipments of large quantities of goods, particularly for exports and imports distributed by land, sea, or air. Therefore, a container must be able to withstand external loads so that goods can safely reach their destination. In this study, seven different models of container skins were developed: general honeycomb, cross honeycomb, square honeycomb, corrugated wall, flat, flat with a single stiffener, and flat with a cross stiffener. Testing was performed using the finite element method. In the static simulation, the best results were obtained by the model with corrugated walls. As the main element and the content of the sandwich panel structure, the core plays a role in increasing the ability of the structure to absorb force, thereby increasing the strength of the material. In the thermal simulation, the best results were obtained by the general honeycomb walls. Vibration simulations also showed that the square honeycomb design was better at absorbing vibration than the other models. Finally, the corrugated model had the best critical load value in the buckling simulation.

NUMERICAL CALCULATION OF THE VACUUM DEGREE FOR A CORRUGATED WALL

The article presents a numerical calculation of the corrugated wall of a transformer under pressure. The permissible degree of evacuation of the wavy transformer tank is determined. The statement of the problem is formulated as follows: to determine the limit of the maximum allowable pressure during the evacuation of the tank with different geometrical dimensions of the corrugation. In this case, the maximum equivalent stress should not exceed the yield point and the walls of the corrugation should not close. Numerical calculation is carried out by the finite element method. This approach to calculating the behavior of a corrugated wall under pressure can be used to determine the maximum allowable internal pressure of the tank.