Removal of Humic Acid Using 3-Methacryloxypropyl Trimethoxysilane Functionalized MWCNT Loaded TiO2/PES Hybrid Membrane

In the present work, a highly efficient mixed matrix membrane (MMM) for humic acid (HA) removal was developed. Multiwalled carbon nanotubes (MWCNTs) were functionalized in the presence of 3-methacryloxypropyl trimethoxysilane using the co-condensation method and were subsequently loaded with TiO2 (prepared via the sol–gel route). The as-prepared material was then incorporated into a PES polymer solution to prepare a fMWCNT-TiO2/PES hybrid membrane via non-solvent induced phase inversion. The microstructure of the membrane was characterized using Fourier transform infrared spectroscopy, atomic force microscopy, scanning electron microscopy, water contact angle, thickness, porosity, and pore size. The fMWCNT-TiO2/PES hybrid membrane was tested for the removal of HA and antifouling performance. The results show that the surface hydrophilicity of the membranes was greatly improved upon the addition of the fMWCNT-TiO2 particles. The results show that 92% of HA was effectively removed after 1 h of filtration. In comparison with pristine membrane, the incorporation of fMWCNT-TiO2 nanoparticles led to enhanced pure water flux (99.05 L/m2 h), permeate flux (62.01 L/m2 h), higher HA rejection (92%), and antifouling improvement (RFR: 37.40%, FRR: 86.02%). Thus, the fMWCNT-TiO2/PES hybrid membrane is considered to be a great potential membrane for the improvement of ultrafiltration membranes.

Preparation of polyacrylate/silica membranes for fuel cell application by in situ UV polymerization

The development of proton conductive polyacrylate membranes based on acrylonitrile, sodium 4-vinylbenzenesulfonate, acrylic acid, ethylene glycol dimethacrylate and hybrid polyacrylate/silica membranes is reported in this article. Polyacrylate membranes were synthesized via UV-initiated copolymerization; for the synthesis of polyacrylate/silica membranes 3-methacryloxypropyl trimethoxysilane-based sol–gel system was introduced into the polymerizing mixture.

Mechanical properties of wood flour/poly (lactic acid) composites coupled with waterborne silane-polyacrylate copolymer emulsion

Wood flour/polylactic acid (WF/PLA) composites were produced with a WF content of 50% based on three types of waterborne polyacrylate (PA) emulsions including a PA homopolymer emulsion and two types of silane-PA copolymer emulsions as coupling agents. Two silanes were in focus, namely, γ-methacryloxypropyl- trimethoxysilane (silane-1) and vinyltrimethoxysilane (silane-2). The emulsions and the modified WFs were characterized, and the effects were investigated in terms of emulsion type and their loading levels on the mechanical properties of WF/PLA composites. (1) Both types of silanes could be successfully copolymerized with PA to form stable emulsions. (2) With increasing PA loading, the mechanical properties (except for flexural modulus) of the composites increased at first before reaching the maximum values at 4% PA loading and then the properties worsened. However, these values were larger than those of pure composites, especially in cases when PA-silane emulsions were applied. (3) PA modified with silane-1 showed the best coupling effect among all the three PA emulsions. The results can be interpreted that PA emulsions are effective coupling agents for the preparation of high-performance WPCs.

Improved antifouling properties and blood compatibility of 3-methacryloxypropyl trimethoxysilane – based zwitterionic copolymer modified composite membranes via in situ post-crosslinking copolymerization

In the present study, a new method to prepare stable antifouling and blood compatible membranes is developed, i.e., in situ post-crosslinking copolymerization.