Synergistic Excitation Mechanism of CaO-SiO2-Al2O3-SO3 Quaternary Active Cementitious System

In this study, the influence of steel slag (SS) content on the strength of the cementitious materials was investigated. The quaternary active cementitious material (CaO-SiO2-Al2O3-SO3) was prepared using various proportions of steel slag (SS), granulated blast furnace slag (BFS), and desulfurized gypsum (DG). The mechanism of synergistic excitation hydration of the cementitious materials was examined using various techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectrometry (FTIR). The strength of the mortar test block was initially increased and decreased later with the increase of the SS content. Mortar test block with 20% steel slag, 65% granulated blast furnace slag, and 15% desulfurized gypsum with 0.35 water-binder ratio showed the highest compressive strength of 57.3 MPa on 28 days. The free calcium oxide (f-CaO) in the SS reacted with water and produced calcium hydroxide (Ca(OH)2) which created an alkaline environment. Under the alkaline environment, the alkali-activated reaction occurred with BFS. In the early stage of hydration reaction, calcium silicate hydrate (C-S-H) gel and fibrous hydration product ettringite (AFt) crystals were formed, which provided early strength to the cementitious materials. As the hydration reaction progressed, the interlocked growth of C-S-H gel and AFt crystals continued and promoted the increase of the strength of the cementitious system.

MODIFICATION OF CEMENTITIOUS MATRIX OF RAPID-HARDENING HIGH-PERFORMANCE CONCRETES

The paper presents the results of research concerning the peculiarities of modern High Performance Concretes based on cementitious systems "Portland cement – active mineral additives – micro fillers – superplasticizers – accelerators of hardening". Physico-chemical regularities of structure formation of super plasticized cementitious systems are established. It is shown that the formation of secondary fine ettringite due to the interaction of active alumina with calcium hydroxide and gypsum in the non-clinker part of the binder because of the effect of "self-reinforcement" compensates for shrinkage and increases the strength of the cementitious system. The modification of the cementitious matrix makes it possible to obtain Rapid Hardening High Performance Concretes that provide early loading and turnover of the formwork of monolithic constructions.

Influence of Redispersible Powder on Properties of Self-Leveling Mortar of Ternary Cementitious System

The self-leveling mortar (SLM) of a ternary cementitious system with different dosages of redispersible powder (RP) with ordinary Portland cement (OPC), sulfoaluminate cement (SAC), and calcium sulfate (CS) as cementitious materials was investigated with regard to fluidity, bond strength, shrinkage rate, abrasion resistance, flexural strength, and compressive strength. The performance parameters obtained from the experimental test for SLM were weighted values calculated with an analytic hierarchy process (AHP). The comprehensive index of performance was evaluated on the basis of a weighted-sum method, and the optimal dosage of RP was determined according to the comprehensive index. The experimental results demonstrated that the fluidity of SLM decreased with the increase in RP dosage at the beginning but then increased thereafter and decreased rapidly as the dosage went beyond 3.0%. The addition of RP resulted in a significant improvement in bond strength (of SLM), reduction in the shrinkage rate, abrasion loss, early flexural strength and compressive strength, and resistance to cracking. The properties of SLM with 3.0% RP can meet the requirements of the industrial standard for cementitious self-leveling floor mortar. Compared with the SLM without RP, the bond strength of SLM with 3.0% RP was increased by 46.7%, while the shrinkage rate and abrasion loss were reduced by 50% and 71.9% respectively. The weighted values of fluidity, compressive strength, flexural strength, stability, cohesiveness, and abrasion resistance were 0.422, 0.196, 0.196, 0.089, 0.058, and 0.039, respectively. A higher value of the comprehensive index generally denotes a better performance. The comprehensive index of SLM with 3.0% RP was the highest.

Magnetorheological composite materials (MRCMs) for instant and adaptable structural control

Magnetic responsive materials can be used in a variety of applications. For structural applications, the ability to create tunable moduli from relatively soft materials with applied electromagnetic stimuli can be advantageous for light-weight protection. This study investigated magnetorheological composite materials involving carbonyl iron particles (CIP) embedded into two different systems. The first material system was a model cementitious system of CIP and kaolinite clay dispersed in mineral oil. The magnetorheological behaviors were investigated by using parallel plates with an attached magnetic accessory to evaluate deformations up to 1 T. The yield stress of these slurries was measured by using rotational and oscillatory experiments and was found to be controllable based on CIP loading and magnetic field strength with yield stresses ranging from 10 to 104 Pa. The second material system utilized a polystyrene-butadiene rubber solvent-cast films with CIP embedded. The flexible matrix can stiffen and become rigid when an external field is applied. For CIP loadings of 8% and 17% vol %, the storage modulus response for each loading stiffened by 22% and 74%, respectively.

EFFECTS OF BIO-BASED PLASTICIZERS, MADE FROM STARCH, ON THE PROPERTIES OF FRESH AND HARDENED METAKAOLIN-GEOPOLYMER MORTAR: BASIC INVESTIGATIONS

Conventional superplasticizers based on polycarboxylate ether (PCE) show an intolerance to clay minerals due to intercalation of their polyethylene glycol (PEG) side chains into the interlayers of the clay mineral. An intolerance to very basic media is also known. This makes PCE an unsuitable choice as a superplasticizer for geopolymers. Bio-based superplasticizers derived from starch showed comparable effects to PCE in a cementitious system. The aim of the present study was to determine if starch superplasticizers (SSPs) could be a suitable additive for geopolymers by carrying out basic investigations with respect to slump, hardening, compressive and flexural strength, shrinkage, and porosity. Four SSPs were synthesized, differing in charge polarity and specific charge density. Two conventional PCE superplasticizers, differing in terms of molecular structure, were also included in this study. The results revealed that SSPs improved the slump of a metakaolin-based geopolymer (MK-geopolymer) mortar while the PCE investigated showed no improvement. The impact of superplasticizers on early hardening (up to 72 h) was negligible. Less linear shrinkage over the course of 56 days was seen for all samples in comparison with the reference. Compressive strengths of SSP specimens tested after 7 and 28 days of curing were comparable to the reference, while PCE led to a decline. The SSPs had a small impact on porosity with a shift to the formation of more gel pores while PCE caused an increase in porosity. Throughout this research, SSPs were identified as promising superplasticizers for MK-geopolymer mortar and concrete.