Resveratrol-Loaded Hydrogel Contact Lenses with Antioxidant and Antibiofilm Performance

Contact lenses (CLs) are prone to biofilm formation, which may cause severe ocular infections. Since the use of antibiotics is associated with resistance concerns, here, two alternative strategies were evaluated to endow CLs with antibiofilm features: copolymerization with the antifouling monomer 2-methacryloyloxyethyl phosphorylcholine (MPC) and loading of the antioxidant resveratrol with known antibacterial activity. MPC has, so far, been used to increase water retention on the CL surface (Proclear® 1 day CLs). Both poly(hydroxyethyl methacrylate) (HEMA) and silicone hydrogels were prepared with MPC covering a wide range of concentrations (from 0 to 101 mM). All hydrogels showed physical properties adequate for CLs and successfully passed the hen’s egg-chorioallantoic membrane (HET-CAM) test. Silicone hydrogels had stronger affinity for resveratrol, with higher loading and a slower release rate. Ex vivo cornea and sclera permeability tests revealed that resveratrol released from the hydrogels readily accumulated in both tissues but did not cross through. The antibiofilm tests against Pseudomonas aeruginosa and Staphylococcus aureus evidenced that, in general, resveratrol decreased biofilm formation, which correlated with its concentration-dependent antibacterial capability. Preferential adsorption of lysozyme, compared to albumin, might also contribute to the antimicrobial activity. In addition, importantly, the loading of resveratrol in the hydrogels preserved the antioxidant activity, even against photodegradation. Overall, the designed hydrogels can host therapeutically relevant amounts of resveratrol to be sustainedly released on the eye, providing antibiofilm and antioxidant performance.

Relationships between the material properties of silicone hydrogels: Desiccation, wettability and lubricity

Silicone hydrogels (SiHy), represent composite matrices composed of hydrophobic gas permeable silicone (Si) rich core and a surface enriched with hydrophilic polymer moieties. Their utilization in contact lens design requires number of SiHy properties (hydration, wettability, lubricity) to be optimized for the challenging conditions at the ocular surface. Typical limitations in literature are that (i) these properties are studied in isolation, monitoring only one parameter but not the rest of them, and (ii) measurements are performed with hydrated samples immediately after removal from storage solutions. Here we study the simultaneous evolution of critical material properties (evaporative loss of water, water contact angle, coefficient of friction) of different SiHy subjected to continuous blink-like desiccation/rehydration cycling. SiHy with wetting agents incorporated in their core (narafilcon A, senofilcon A) were particularly susceptible to extended desiccation. Stenfilcon A, a material with only 3% bulk Si content maintained its performance for 4 h of cycling, and delefilcon A (80% surface water content) resisted extended 8 h of desiccation/rehydration runs. Strong correlation exists between the evolution of SiHy wettability and lubricity at ≥4 h of blink-like cycling. Understanding the interplay between SiHy properties bears insights for knowledge based design of novel ophthalmic materials.

Impact of Air Exposure Time on the Water Contact Angles of Daily Disposable Silicone Hydrogels

The wettability of silicone hydrogel (SiHy) contact lens (CLs) is crucial for the pre-lens tear film stability throughout the day. Therefore, sessile drop and captive bubble setups were used to study the advancing and receding water contact angles (CA) of four SiHy materials: narafilcon A (TE), senofilcon A (AOD), stenfilcon A (MD), and delefilcon A (DT). TE and AOD have 48% and 38% water content, respectively, and no surface coating. MD (54% water) implements “smart chemistry” with just 4.4% bulk silicone content, while DT has >80% water at its surface. These SiHy were subjected to continuous blink-like air exposure (10 s)/rehydration (1s) cycles for 0, 1, 2, 3, 4, 6, 8, 10, 12, 14, and 16 h. The advancing CA, which measures the rehydration propensity of the CL surface, proved to be the most sensitive parameter to discriminate between the samples. The order of performance for the entire time scale was DT > MD >> AOD ≥ TE. The extended desiccation/rehydration cycling increased the differences between the CA of DT and MD compared to AOD and TE. This suggests that the low Si surface content and the high surface hydration are major determinants of SiHy wettability.