Evaluation of Two Fast Virtual Stenting Algorithms for Intracranial Aneurysm Flow Diversion

Background: Endovascular treatment of intracranial aneurysms (IAs) by flow diverter (FD) stents depends on flow modification. Patient-specific modeling of FD deployment and computational fluid dynamics (CFD) could enable a priori endovascular strategy optimization. We developed a fast, simplistic, expansion-free balls-weeping algorithm to model FDs in patientspecific aneurysm geometry. However, since such strong simplification could result in less accurate simulations, we also developed a fast virtual stenting workflow (VSW) that explicitly models stent expansion using pseudo-physical forces. Methods: To test which of these two fast algorithms more accurately simulates real FDs, we applied them to virtually treat three representative patient-specific IAs. We deployed Pipeline Embolization Device into 3 patient-specific silicone aneurysm phantoms and simulated the treatments using both balls-weeping and VSW algorithms in computational aneurysm models. We then compared the virtually deployed FD stents against experimental results in terms of geometry and post-treatment flow fields. For stent geometry, we evaluated gross configurations and porosity. For post-treatment aneurysmal flow, we compared CFD results against experimental measurements by particle image velocimetry. Results: We found that VSW created more realistic FD deployments than balls-weeping in terms of stent geometry, porosity and pore density. In particular, balls-weeping produced unrealistic FD bulging at the aneurysm neck, and this artifact drastically increased with neck size. Both FD deployment methods resulted in similar flow patterns, but the VSW had less error in flow velocity and inflow rate. Conclusion: In conclusion, modeling stent expansion is critical for preventing unrealistic bulging effects and thus should be considered in virtual FD deployment algorithms. Also endowed with its high computational efficiency and superior accuracy, the VSW algorithm is a better candidate for implementation into a bedside clinical tool for FD deployment simulation.

A Hypothetical Vascular Stent with Locally Enlarged Segment and the Hemodynamic Evaluation

Among the interventional stenting methods for treating coronary bifurcation lesions, the conventional treatments still have disadvantages, which include increased intervention difficulties or inadequate supply of blood flow to side branches and may alter the physiological function of downstream organs. Thus, the optimized design of stent geometry needs to be improved based on the specific shape of branches to minimize the complications of inadequate blood flow to the downstream organs and tissues. Our research used 3D modeling and fluid dynamics simulation to design and evaluate a new stent with locally enlarged segment by altering the proportion and length of enlarged surface area based on Bernoulli’s equation. The aim is to increase the pressure and blood flow supply at side branches. According to series of blood flow simulations, the stent with 10% enlargement of surface area and length of 3 folders of stent diameter was assigned as the optimized design. The results revealed that by using this design, according to the simulation results, the average pressure on side branches increased at the rate of 43.6%, which would contribute to the adequate blood supply to the downstream organs. Besides, the average wall shear stress (WSS) at sidewalls increased at 9.2% while the average WSS on the host artery wall decreased at 14.1%. There is in the absent of noticeable rise in the total area of low WSS that blows the threshold of 0.5 Pa. Therefore, the present study provides a new method to optimize the hemodynamics features of stent for bifurcation arteries.

P1967Impact of strut thickness, of number of crown and connectors on clinical outcomes on patients treated with second generation DES

Introduction In new generation drug eluting stents (DESs) era, the impact of stent geometry on freedom from recurrent events has been poorly explored. Impact of struts thickness, number of crowns and connectors on clinical outcomes was evaluated in the present study. Methods Randomized controlled trials comparing last generation DESs were selected. The primary endpoint was the rate of target lesion revascularization (TLR), while secondary was Definite Stent Thrombosis (ST). Results 53 studies with 52006 patients were included. A struts thickness ≤81 nm was associated with a lower incidence of TLR (2.9%: 2.4–3.4 vs. 3.6%: 3.0–4.3) and ST (0.8%: 0.6–1.1 vs. 1.3%: 0.9–1.8). A mean number of connectors >2.5 was also associated with a lower incidence of TLR (3.2%: 2.8–3.6 vs. 3.5%: 2.9–4.2) and ST (1.0%:0.8–1.3 vs. 1.3%: 0.9–1.7 vs for ST). On the other hand, stents with average number of crowns <7.5 did not perform better than stents with higher average number of crowns. Conclusions The findings of the study support that lower struts thickness and higher numbers of connectors have a positive clinical outcome reducing stent thrombosis and target lesion revascularizations, while the average number of stent crowns plays a secondary role.

Performance of BeGraft and BeGraft+ Stent-Grafts as Bridging Devices for Fenestrated Endovascular Aneurysm Repair: An In Vitro Study

Purpose: To investigate 2 generations of balloon-expandable covered stents as potential bridging devices using an in vitro model of stent-graft fenestrations. Materials and Methods: Twenty BeGraft and 20 BeGraft+ cobalt-chromium stents covered in expanded polytetrafluoroethylene (ePTFE) in 6- and 8-mm diameters were tested in sheets mimicking stent-graft fenestrations. Microscopy and radiography were employed to evaluate stent morphology after flaring. In vitro bench tests measured maximum pullout (perpendicular displacement) and the shear stress (axial displacement) forces needed to dislocate the stents. Results: No alteration of ePTFE coverage was detected in the flared stents. Digital radiography and computed tomography showed marked alteration of the stent geometry, which was more pronounced in the BeGraft group. No fractures were detected. Median (minimum–maximum) pullout forces for the 6-mm stent-grafts were 17.1 N (15.8–19.6) for the BeGraft device and 30.4 N (20.2–31.9) for the BeGraft+ device (p=0.006). Median (minimum–maximum) pullout forces for the 8-mm stent-grafts were 11.3 N (11–12.1) for the BeGraft device and 21.8 N (18.2–25.5) for the BeGraft+ device (p<0.001). The shear stress test showed median forces of 10.5 vs 15.28 N at 150% of the stent diameter for the 6-mm BeGraft and BeGraft+ stent-grafts, respectively, and 15.23 vs 20.72 N at 150% stent diameter for the 8-mm models (p=0.016 and 0.017, respectively). Conclusion: Flaring changed the stent geometry but did not provoke stent fractures. The BeGraft+ is superior to the BeGraft in terms of pullout and shear stress forces, demonstrating greater resilience.

PALMAZ–SCHATZ STENT-OPENING MECHANICS USING A SIMPLE APPROACH INVOLVING THE BALLOON–STENT AND STENT–ARTERY CONTACT PROBLEM: APPLICATION TO BIOPOLYMER STENTS

We used the finite element method-based toolbox COMSOL Multiphysics to address the important question of biopolymer coronary stent mechanics. We evaluated the diameter of the stent, the immediate elastic recoil, the dogboning and the foreshortening during deployment while using an idealized model that took into account the presence of the balloon and the coronary artery wall (equivalent pressure hypothesis). We validated our model using the well-known mechanics of the Palmaz–Schatz metal stent and acquired new data concerning a poly-L-lactic acid (PLLA) stent and some other biodegradable co-polymer-based stents. The elastic recoil was relatively high (26.1% to 31.1% depending on the biopolymer used) when taking into account the presence of both the balloon and artery. The dogboning varied from 31% to 46% for the polymer stents and was 62% for the metal stent, suggesting that less arterial damage could be expected with biopolymer stents. Various strut thicknesses were tested for the PLLA stent (114, 180 and 250[Formula: see text][Formula: see text]m) and no significant improvement in elastic recoil was observed. We concluded that the stent geometry has a greater impact on the scaffolding role of the structure than the strut thickness, or even the mechanical properties of the stent.