A Shot Number Based Approach to Performance Analysis in Table Tennis

The current study proposes a novel approach that improves the conventional performance analysis in table tennis by introducing the concept of frequency, or the number of shots, of each shot number. The improvements over the conventional method are as follows: better accuracy of the evaluation of skills and tactics of players, additional insights into scoring and returning skills and ease of understanding the results with a single criterion. The performance analysis of matches played at the 2012 Summer Olympics in London was conducted using the proposed method. The results showed some effects of the shot number and gender differences in table tennis. Furthermore, comparisons were made between Chinese players and players from other countries, what threw light on the skills and tactics of the Chinese players. The present findings demonstrate that the proposed method provides useful information and has some advantages over the conventional method.

Taper Angle of Silicon Nitride Thin Film Control by Laser Direct Pattern for Transistors Fabrication

Silicon nitride (SiNx), an important material used as a dielectric layer and passivation layer in thin film transistor liquid crystal display (TFT LCD) was patterned by a non-lithographic process. SiNx was deposited by plasma enhanced chemical vapor deposition (PECVD) on glass substrate. Laser photoablation can effectively pattern 5 µm diameter with 200 nm depth hole in SiNx thin films with laser photoablation. The threshold remove fluence is 1350 mJ/cm2 with 1 laser irradiation shot. The contact-hole taper angle as a function of the laser irradiation shot number. The taper angle increased with increasing the laser irradiation shot number. The contact-hole taper angle etched profile was successfully controlled by vary the laser irradiation shot number.

Effect of Shot Number on Crater Formation of Magnesium Alloy Modified with High-Intensity Pulsed Ion Beam

HIPIB irradiation of magnesium alloy is carried out at a specific ion current density of 100 A/cm2 with shot number from one to ten in order to explore the effect of shot number on crater formation of magnesium alloy. Surface morphologies, surface roughness and mean spacing of surface profile irregularities of the irradiated samples are examined by scanning electron microscopy (SEM) and profilometer technique, respectively. It is found that the surface roughness, the mean spacing of surface profile irregularities, and the maximum crater diameter on the irradiated surface increase with increasing shot number, whereas the crater density decreases as the shot number increases.

Improved Wear Resistance of Magnesium Alloy Irradiated by High-Intensity Pulsed Ion Beam at Lower Energy Density

HIPIB irradiation experiment is carried out at lower energy density of 0.55 J/cm2 with shot number from 1 to 10, and dry sliding wear behavior is investigated in order to explore the low energy-modification of magnesium alloy by HIPIB. It is found that HIPIB irradiation leads to the increase in surface hardness and therefore the improvement in wear resistance compared with the original sample. The improved wear resistance is mainly ascribed to the enhanced surface hardness induced by HIPIB irradiation.

Effect of High-Intensity Pulsed Ion Beam Irradiation on the Electrochemical Corrosion Behavior of AZ31 Magnesium Alloy

HIPIB irradiation experiment is carried out at a specific ion current density of 1.1 J/cm2 with shot number from one to ten in order to explore the effect of shot number on electrochemical corrosion behavior of magnesium alloy. Surface morphologies, microstructure and corrosion resistance of the irradiated samples are examined by scanning electron microscopy (SEM), transmission electron microscope (TEM) and potentiodynamic polarization technique, respectively. It is found that HIPIB irradiation leads to the increase in open circuit potential, corrosion potential and breakdown potential, and the decrease in the corrosion current density and the corrosion rate as compared to the original sample. The improved corrosion resistance is mainly attributed to the grain refinement and surface purification induced by HIPIB irradiation.

Ultrasonic Characterization of EB-PVD Thermal Barrier Coatings Irradiated by HIPIB

High-intensity pulsed ion beam (HIPIB) irradiation at 300 A/cm2 with a shot number of 1, and 5 was performed on the coatings and caused the modification of properties. Porosity and rough surface of EB-PVD (Electron Beam-Physical Vapor Deposition) deposited ZrO2-7%Y2O3 coatings with the thickness of 150 μm on heat-resistant steel have been characterized using the ultrasonic reflection coefficient phase spectrum. With increasing the shot number, the surface remelting and ablating filled gaps and caves between columns, and induced more uniform and compact structure. The ultrasonic measurement was investigated using immersion focusing pulse echo method with a 10 MHz transducer. The ultrasonic reflection coefficient related to frequency, velocity and attenuation coefficient were analyzed based on the acoustic transmission model in a multi-layered structure. For the as-deposited coating and coatings irradiated by HIPIB with the shot number of 1 and 5, the ultrasonic velocity changed from 2950 to 3170, and 3255 m/s respectively. The relationship between the attenuation coefficient and the frequency has been deduced based on the numerical fitting of the phase spectrum. The corresponded expressions are 1.35 α = 0.105 f , 1.2 α = 0.045 f and 1.14 α = 0.035 f , which displays that the attenuation coefficient decreases with the increasing of shot number. The ultrasonic results are in agreement with SEM observations, which have indicated that the coatings became denser and uniform with increasing the shot number. From the velocity and attenuation coefficient, the density, porosity, and microcracks of the coatings can be nondestructively evaluated utilizing the method of this paper.