Response Analysis of Asymmetric Monostable Harvesters Driven by Color Noise and Band-Limited Noise

In this paper, we investigate the response of asymmetric potential monostable energy harvesters (MEHs) excited by color noise and band-limited noise. The motivation for this study is that environmental vibrations always have the characteristic of randomness, and it is difficult to modulate a perfectly symmetric MEH. For the excitation of exponentially correlated color noise, the moment differential equation was applied to evaluate the output performance of the asymmetric potential MEHs. Numerical and theoretical analyses were carried out to investigate the influence of noise intensity and internal system parameters on the output power of the system. Our results demonstrate that the output performance of the asymmetric MEH decreases with the increase in the correlation time, which determines the character of the color noise. On the contrary, the increase in the asymmetric degree enhances the output power of the asymmetric MEH subjected to color noise. For the band-limited noise excitation, numerical simulation is undertaken to consider the response of the asymmetric MEHs, and outcomes indicate that the frequency bandwidth and center frequency have a significant influence on the output performance. Regarding the asymmetric potential, its appearance leads the MEHs to generate higher output power at lower frequencies and this phenomenon is more obvious with the increase in the degree of asymmetry. Finally, we observed that the characteristics of the response bandwidth of asymmetric MEHs subjected to band-limited noise excitation are similar to the response under harmonic excitation.

All-in-One High-Power-Density Vibrational Energy Harvester with Impact-Induced Frequency Broadening Mechanisms

This paper proposes an electrostatic-piezoelectric-electromagnetic hybrid vibrational power generator with different frequency broadening schemes. Both the nonlinear frequency broadening mechanisms and the synergized effect of the electrostatic-piezoelectric-electromagnetic hybrid structures are investigated. The structure and performance of the composite generator are optimized to improve the response bandwidth and performance. We propose that the electrostatic power generation module and the electromagnetic power generation module be introduced into the cantilever beam to make the multifunctional cantilever beam, realizing small integrated output loss, high output voltage, and high current characteristics. When the external load of the electrostatic power generation module is 10 kΩ, its peak power can reach 3.6 mW; when the external load of the piezoelectric power generation module is 2 kΩ, its peak power is 2.2 mW; and when the external load of the electromagnetic power generation module is 170 Ω, its peak power is 0.735 mW. This means that under the same space utilization, the performance is improved by 90%. Moreover, an energy management circuit (ECM) at the rear end of the device is added, through the energy conditioning circuit, the device can directly export a 3.3 V DC voltage to supply power to most of the sensing equipment. In this paper, the hybrid generator’s structure and performance are optimized, and the response bandwidth and performance are improved. In general, the primary advantages of the device in this paper are its larger bandwidth and enhanced performance.

Soft, tough, and fast polyacrylate dielectric elastomer for non-magnetic motor

Dielectric elastomer actuators (DEAs) with large electrically-actuated strain can build light-weight and flexible non-magnetic motors. However, dielectric elastomers commonly used in the field of soft actuation suffer from high stiffness, low strength, and high driving field, severely limiting the DEA’s actuating performance. Here we design a new polyacrylate dielectric elastomer with optimized crosslinking network by rationally employing the difunctional macromolecular crosslinking agent. The proposed elastomer simultaneously possesses desirable modulus (~0.073 MPa), high toughness (elongation ~2400%), low mechanical loss (tan δm = 0.21@1 Hz, 20 °C), and satisfactory dielectric properties ($${\varepsilon }_{{{{{{\rm{r}}}}}}}$$ ε r = 5.75, tan δe = 0.0019 @1 kHz), and accordingly, large actuation strain (118% @ 70 MV m−1), high energy density (0.24 MJ m−3 @ 70 MV m−1), and rapid response (bandwidth above 100 Hz). Compared with VHBTM 4910, the non-magnetic motor made of our elastomer presents 15 times higher rotation speed. These findings offer a strategy to fabricate high-performance dielectric elastomers for soft actuators.

Response Bandwidth Design of Fabry-Perot Sensors for Partial Discharge Detection Based on Frequency Analysis

The insulation of power equipment can be effectively assessed by analyzing the acoustic signals originated from partial discharges (PD). Fabry-Perot (F-P) sensors are capable of detecting PD acoustic signals. Although the frequency bandwidth of an F-P sensor is mainly referred to conventional piezoelectric transducer (PZT) sensor, it is still doubtful to identify a suitable bandwidth for fiber sensors in detection of PD signals. To achieve a suitable bandwidth for an F-P sensor, the frequency distribution of PD acoustic emission is investigated, and an extrinsic F-P sensor is designed to detect acoustic signals generated from PD. F-P sensors with different intrinsic frequencies are fabricated as possible design standards of bandwidth for acoustic detection. PD acoustic signals are detected by these F-P sensors and PZT sensors in the experimental system, in which four typical electrode models are employed. The measured results of frequency performance are analyzed in linear and semilogarithmic coordinates. The results show that F-P sensors can effectively detect PD acoustic emissions in both wideband and narrowband modes. Moreover, F-P sensors achieve a higher sensitivity in the narrowband mode. We propose that intrinsic frequency of the F-P sensor should be designed in the frequency range of 100–170 kHz to obtain maximum sensitivity.