Evolution of Water Conveyance Capacity through Hydraulic Transition Processes in Circular Drop Manholes

Circular drop manholes are widely implemented for steep catchments in urban drainage networks. Poor downstream hydraulic transition processes of a manhole system, i.e., the formation of hydraulic jump near the outlet entrance, and the sudden transition from free surface to pressurized flow with bursts of air in the outflow pipe can severely constraint the capacity of water conveyance. In this paper, we defined four basic hydraulic stages that indicate where hydraulic transition processes begin and end. The measurements of typical manhole models with different drop heights were conducted under different inflow and outflow conditions. Three types of transition processes covering all flow patterns have resulted into a graphical visualization by analyzing two pairs of dimensionless parameters. The flow inside a circular drop manhole was considered to reach its discharge capacity when the abrupt drop of manhole water level is visible in the fully aerated flow pattern. Four empirical equations revealing the water level filling ratio and discharge efficiency at different hydraulic stages were also presented for further predictions of choking risks.

Performance Assessment of Shockwaves of Chute Spillways in Large Dams

Spillways are the most important structures of large dams that are responsible for releasing the excessive flood discharge from the reservoir. Although many studies have been performed to determine the flow characteristics over these structures, however, the available information on the shockwaves’ characteristics for spillways’ design is limited. The supercritical flow below the chute piers generates an aerated flow known as shockwaves. Due to the flow interaction with the chute piers, three kinds of standing waves just downstream of the pier, in the middle of the chute, and on the sidewalls are generated. This phenomenon affects the flow domain and its hydraulic characteristics along the chute spillway. The height of the waves increases downstream, where they hit the chute walls and reflect again into the flow to interact together again. The process repeated and intensified downstream in a lozenge shape. The height of these waves can be more than twice the depth flow and thus run over the sidewalls. This is important for the design of chute walls in chute spillways with control gates. In this study, the experimental formation of the shockwaves and their behavior along the chute and their reduction measures are presented. Experiments were conducted on a scaled physical model (1/50) of Kheirabad Dam, Water Research Institute, Iran. It was realized that apart from the geometry of piers and chute spillway, Froude number of flow and gate opening are the main effective parameters on the hydraulic performance of shockwaves’ formation and their development on gated spillways.

Numerical Simulation Study on Distribution of Bubble in Flow near Aerator Based on CFD-PBM Coupled Model in Tunnel

The aerator can reduce erosion by mixing a large amount of air into the water in the solid wall area. The effectiveness of erosion reduction is mainly based on air concentration and its bubble size distribution. However, simultaneous simulation of the air concentration and its bubble size distribution in numerical simulations is still a hot and difficult area of research. Aiming at the downstream aerated flow of hydraulic aeration facilities, several numerical models, such as VOF, mixture, Euler, and Population Balance Model (PBM), are compared and verified by experiments. The results show that the CFD-PBM coupled model performs well compared to other conventional multiphase models. It can not only obtain the evolution law of the bubble distribution downstream of the aerator but also accurately simulate the recombination and evolution process of bubble aggregation and breakage. The Sauter mean diameter of the air bubbles in the aerated flow decreases along the way and eventually reaches a stable value. The bubble breakage is the main process in the development of the bubbles. It reveals the aeration law that the small air bubbles are closer to the bottom plate, while the large bubbles float up along the aerated flow, which provides a powerful support for the basic research on the mechanism of aeration and erosion reduction.

Effect of Height and Geometry of Stepped Spillway on Inception Point Location

Air entrainment in a stepped spillway is very important to protect the spillway from cavitation damage. The inception point is the location where air starts entering the non-aerated flow zone. The inception point location depends on different parameters, such as the discharge, step height, and step shape. In this paper, various stepped spillways, including flat steps, pooled steps, and round steps with different step heights were numerically simulated using the volume of fluid and realizable k-ε models. The results indicate that the inception point location moves downwards with the increase of the discharge of the stepped spillways. The length of the non-aerated flow zone increases with the discharge. The inception point location moves downwards as the step height decreases and the step number increases at the same discharge. The inception point location of the round stepped spillway model is much closer to the spillway crest than that of the flat stepped spillway with the same number of steps. The inception point location of the pooled stepped spillway is closer to the spillway crest than that of the flat stepped spillway, but more downstream than that of the round stepped spillway.