Combustion Characterisation of Bituminous Coal and Pinus Sawdust Blends by Use of Thermo-Gravimetric Analysis

The cocombustion of coal and pinus sawdust waste is an economically viable and sustainable option for increasing the share of biomass in energy production. This technology also has the potential to reduce the emission of greenhouse gases from existing coal fired power plants. The thermal synergistic effects of cocombusting Hwange bituminous coal (HC) with Pinus sawdust (PS) were thus investigated using thermogravimetric analysis. Fuel blending mass ratios of 100HC, 90HC10PS, 80HC20PS, 70HC30PS, and 100PS under an oxidative atmosphere at three different heating rates of 5, 12.5, and 20 °C/min were used for the experimental setup. Zero to negative synergy was generally observed for the mass loss curves (TG) at different blending ratios. Generally positive synergy was observed with relation to rate of mass loss curves (DTG) for the 80HC20PS and 70HC30PS fuel blends only. The ignition index increased with blending ratio by an average of 42.86%, whilst the burnout index showed a maximum increase of 14.6% at 20 °C/min. However, the combustion index representative of stability showed a decreasing trend generally for all the heating rates. No combustion index produced a linear variation with temperature, though upon evaluation, an optimum mass ratio of 20% pinus sawdust was suggested. The chosen optimum blending ratio demonstrated increased ignition and burnout indexes whilst maintaining the stability of combustion at a reasonable range.

How CO2-to-Diesel Technology Could Help Reach Net-Zero Emissions Targets: A Canadian Case Study

Carbon capture, utilization, and storage (CCUS) is an attractive technology for the decarbonization of global energy systems. However, its early development stage makes impact assessment difficult. Moreover, rising popularity in carbon pricing necessitates the development of a methodology for deriving carbon abatement costs that are harmonized with the price of carbon. We develop, using a combined bottom-up analysis and top-down learning curve approach, a levelized cost of carbon abatement (LCCA) model for assessing the true cost of emissions mitigation in CCUS technology under carbon pricing mechanisms. We demonstrate our methodology by adapting three policy scenarios in Canada to explore how the implementation of CO2-to-diesel technologies could economically decarbonize Canada’s transportation sector. With continued policy development, Canada can avoid 932 MtCO2eq by 2075 at an LCCA of CA$209/tCO2eq. Technological learning, low emission hydroelectricity generation, and cost-effective electricity prices make Quebec and Manitoba uniquely positioned to support CO2-to-diesel technology. The additional policy supports beyond 2030, including an escalating carbon price, CO2-derived fuel blending requirements, or investment in low-cost renewable electricity, which can accelerate market diffusion of CO2-to-diesel technology in Canada. This methodology is applicable to different jurisdictions and disruptive technologies, providing ample foci for future work to leverage this combined technology learning + LCCA approach.

Comparison of Used Locomotive Fuel Filters after Using B20 and B0 Fuels

The automotive and non-automotive sectors have followed the Indonesian government's policy regarding applying high concentration biodiesel use. Some issues arise from the effects of using a high biodiesel concentration on engine components, such as filter blocking or degradation. Therefore, various parties have challenged to improve both in terms of fuel quality and engine components. Meanwhile, testing of high concentration biodiesel fuel (blending ratio above 10 %) was still rarely published in the rail transport sector. Therefore, the rail test aimed to evaluate the effect of B20 fuel on locomotive engine components. The test was conducted during two periodic maintenance (6 months) using two trains with B20 and B0 fuels as a comparison. This study discusses the effect of B20 on fuel filters by performing tests on used filters for one periodic maintenance (3 months). The morphological analysis of deposits was conducted using a digital microscope, while TGA, GC-MS, FTIR, and elemental analysis were used to determine its components. The results showed that biodiesel filtration in the main filter was higher, and the subsequent filtration showed fewer deposits than that of pure diesel. Various types of fuel filter deposits have been identified, such as hydrocarbons and fatty acid methyl esters.

A Study on Bio-Diesel and Jet Fuel Blending for the Production of Renewable Aviation Fuel

Aviation industry is considered one of the contributors to atmospheric CO2emissions. It is forced to cut off carbon dioxide emission starting 2020. Current trends in bio-jet production involve mega projects with million dollars of investments. In this study, bio-jet fuel production by blending bio-diesel with traditional jet fuel at different concentrations of bio-diesel (5, 10, 15, 20 vol. %) was investigated. This blending technique will reduce bio-jet production cost compared to other bio-jet techniques. Bio-diesel was originally produced by the transesterification of non-edible vegetable oil (renewable sources), so, its blend with jet fuel will has a reduced carbon foot print. The blend was tested to ensure that the end product will meet the ASTM D1655 international specifications for Jet A-1 and Jet A and can be used in aircrafts.Available data on biodiesel blending with jet fuel in the literature is not consistent, there are many contradictory results. Hence, more investigations are required using locally available feedstocks. The main physicochemical properties for Jet A-1 and Jet A according to ASTM D1655 were tested to check if the blend will be compatible with existing turbojet engine systems. Different tests were conducted; vacuum distillation, smoke point, kinematic viscosity, density, flash point, total acidity and freezing point. In addition, heating value of the blend was calculated. The result was then compared with calculated value using blending indices available in the literature. Blending indices were able to predict the laboratory measured specifications for the studied blends.It was found that only 5% bio-diesel- 95% jet fuel blend (B5) meets ASTM standard for Jet A. Hence, biodiesel can be safely used as a blend with fossil-based jet for a concentration of up to 5% without any change in the ASTM specifications. Freezing point is the most important constrain for this blending technique. Higher blends of biodiesel will cause the bio-jet blend to fail ASTM specifications. In general, blending technique will reduce the cost impact that may have been incurred due to change in infrastructure when using other production techniques.