Settlement Behavior Evaluation of Soft-Clay Layer Reinforced with Sand Piles

In this study, the performances of the sand piles in Istanbul's Bağcılar and Zeytinburnu districts has been analyzed using Finite Element Method (FEM). Single and group (triple) piles with various length/diameter ratios (L/D) were placed in the water-saturated soft clay soil. Sand piles were modeled in various L/D ratios (10, 5.71, and 8.57). The distance between the piles was chosen as 2 meters and the group effect was also investigated. A uniformly distributed load of 162 kN/m2 is placed on the ground. In addition, the soil was modeled with the Soft-Soil soil model, the hardening soil model for the infill part, and the sand piles with the Mohr-Coulomb soil model. According to the results , the settlement of the soil decreases by 52.8% for a single pile with an L/D ratio of 8.57. However, the best L/D ratio for triple piles was found to be 5.71. In this case, the settlement decreases by 52.8% compared to the pileless situation. Finally it was concluded that the model with the L/D ratio of 8.57 reduced settlement in the best and the most efficient way.

Numerical Modeling of Shallow Foundation Behavior Using Soft Soil Model

This study discusses the results of simulation a finite element analysis of the load-settlement curve using soft soil model of shallow foundation subjected to axial load rested on three different types of clayey soils, it was considered different shear strength parameters (C=16, C=25, and C=70). It was concluded for clayey soil of C=16, there was a match to the experimental load – settlement curve using the soft soil model. It was also observed increase in the foundation width led to an increase in bearing capacity, however, bearing capacity increased by around (79 %) for an increase in footing width of (6.25), so it was about (144%) for (12.5).

Applicability of Constitutive Models to Describing the Compressibility of Mining Backfill: A Comparative Study

The compressibility of mining backfill governs its resistance to the closure of surrounding rock mass, which should be well reflected in numerical modeling. In most numerical simulations of backfill, the Mohr–Coulomb elasto-plastic model is used, but is constantly criticized for its poor representativeness to the mechanical response of geomaterials. Finding an appropriate constitutive model to better represent the compressibility of mining backfill is critical and necessary. In this paper, Mohr–Coulomb elasto-plastic model, double-yield model, and Soft Soil model are briefly recalled. Their applicability to describing the backfill compressibility is then assessed by comparing numerical and experimental results of one-dimensional consolidation and consolidated drained triaxial compression tests made on lowly cemented backfills available in the literature. The comparisons show that the Soft Soil model can be used to properly describe the experimental results while the application of the Mohr–Coulomb model and double-yield model shows poor description on the compressibility of the backfill submitted to large and cycle loading. A further application of the Soft Soil model to the case of a backfilled stope overlying a sill mat shows stress distributions close to those obtained by applying the Mohr–Coulomb model when rock wall closure is absent. After excavating the underlying stope, rock wall closure is generated and exercises compression on the overlying backfill. Compared to the results obtained by applying the Soft Soil model, an application of the Mohr–Coulomb model tends to overestimate the stresses in the backfill when the mine depth is small and underestimate the stresses when the mine depth is large due to the poor description of fill compressibility. The Soft Soil model is recommended to describe the compressibility of uncemented or lightly cemented backfill with small cohesions under external compressions associated with rock wall closure.

Material Models to Study the Effect of Fines in Sandy Soils Based on Experimental and Numerical Results

Choosing and calibrating a robust and accurate soil material model (constitutive model) is the first important step in geotechnical numerical modelling. A less accurate model leads to poor results and more difficulty estimating true behaviour in the field. Subsequent design work is compromised and may lead to dangerous and costly mistakes. In this research, laboratory experimental results were used as a basis to evaluate several soil material models offered in Plaxis2D software. The deciding feature of the soil model was how well it could represent effects of percentage of fine material within sandy soils to simulate its behaviour. Results indicate that the Hardening Soil (HS) model works well when the percentage of fine (soft) materials is less than 10%. Above that level, the Soft Soil model (SS) becomes the most suitable. Finally, some important conclusions about this research and recommendations for future research are highlighted.

Design and analysis of biomimetics based excavator bucket and tooth

Within the scope of this paper, various bucket tooth designs and a biomimetic bucket design were created in order to produce a solution on digging efficiency which is one of the general problems of construction machines. These designs were inspired by giant anteater and American badger front claws. The inspiration aspect was diversified by integrating the paw and claw curves of the giant anteater and by bringing American badger claws into the design in different ways. Furhermore, the designed biomimetic bucket alternatives were compared between each other and the standard bucket equipment used in the market by making a computer aided static analysis. The compared criteria were the equivalent stress and total deformation formed on the bucket itself, the excavation equipment and the excavated soil. According to the analysis results, when the bucket tooth named P2 is mounted to the standard bucket, it has 42% lower Von-Mises stress on than standard bucket tooth. Additionally, it is exposed 4,7% less total deformation than standard tooth. Also, in terms of maximum Von-Mises stress formed on the soil model, P2 causes 17,5% greater stress than the standard bucket tooth.

Evaluation of Lateral and Axial Deformation for Earth Pressure Balance (EPB) Tunnel Construction Using 3 Dimension Finite Element Method

Mass Rapid Transit Jakarta (MRTJ) phase 1 tunnel construction using the earth pressure balance method has been completed and surface settlement and lateral displacement data according to elevation and inclinometer readings has been collected to evaluate the effect of tunnel’s construction on surrounding infrastructure. Soil stratification along the research area, defined according to boring logs and soil parameters for the hardening soil model (HSM) and the soft soil model (SSM), was determined by optimization of stress-strain curve fitting between CU triaxial test, consolidation test and soil test models in the Plaxis 3D software. Evaluation of the result of surface settlement measurements using an automatic digital level combined with geodetic GPS for elevation and position control points showed that the displacement behavior was affected by vehicle load and stiffness of the pavement. Lateral displacement measurements using inclinometers give a more accurate result since they are placed on the soil and external influences are smaller than surface settlement measurement. The result of 3D finite element modeling showed that surface settlement and lateral displacement during TBM construction can be predicted using HSM with 2% contraction. SSM and the closed-form solutions of Loganathan and Poulos are unable to provide a good result compared to the actual displacement from measurements.