Effect of Solidifying Structure on Centerline Segregation of S50C Steel Produced by Compact Strip Production

Medium-high carbon steels having a high quality are widely used in China. It is advantageous to produce high value-added hot-rolled plates with the crystal refined and chemical composition homogenized in the casting slabs. However, element segregation occurs easily during high-medium carbon steels’ production. Generally, the centerline segregation is improved by enlarging the equiaxed zone with low-superheat casting and electromagnetic stirring (EMS). Studies were conducted on centerline segregation of S50C steel slabs with a thickness of 52 mm produced by the compact strip production (CSP) process in China without EMS equipped. By sampling along the width at different position, the secondary dendrite arm spacing (SDAS) was measured after etching and picture processing, based on which the cooling rate was calculated. It was found that the cooling rate increased from the center to the surfaces of the slabs ranging in 1~20 K/s, 10 times faster than that of a conventional process. The faster cooling rate led to a refined solidifying structure and columnar dendrite through the center of the slabs. The SDAS tended to increase from surfaces to the center, ranging only 32~120 μm smaller than that of a conventional process in 100~300 μm, indicating a finer solidifying structure by the CSP process. Results by EPMA indicated that elements C, Si, and Mn distribute in dispersed spots, increasing towards the center, and the centerline segregation changed in a narrow range: for C mainly in 1.0~1.1, Si in 0.98~1.08, Mn in 0.96~1.02, respectively, meaning a more chemical homogenization than that of thick slabs. Elements’ segregation originated from solute redistribution between solid and liquid. According to thermodynamic calculation, δ region of S50C is so narrow that the solute redistribution mainly occurred between γ-Fe and liquid during solidification. As the equilibrium partition coefficient of element C was the smallest, it was easy for C to be rejected to the residual liquid in the inter-dendritic space, leading to obvious segregation, relatively. Besides, as a result of high-cooling intensity, the solidifying structure became so fine that the Fourier number increased and the volume of the residual liquid decreased, making centerline segregation alleviated effectively both in volume and degree. Although bulging was observed during the industrial experiment, the centerline segregation was still inhibited obviously as the refining solidifying structure with permeability ranged only in 0.1~2.3 μm2 from the surfaces to centerline, which showed a good resistance on the residual flow towards the centerline.

Influence of Twin-Roll Casting Speed on Microstructural Homogeneity, Centerline Segregation, and Surface Quality of Three Different Mg Alloys

In this work, the influence of twin-roll casting (TRC) speed on the microstructure of the through-thickness uniformity, centerline segregation, and surface quality of three wrought Mg alloys was investigated. The microstructural features of the AZ31, ZX11, and ZWK200 alloys produced at TRC speeds ranging from 1.8 m/min to 2.2 m/min (for the AZ31 and ZWK200), and 1.5–2.5 m/min (for the ZX11 alloy) were analyzed. There were clear differences in the microstructure uniformity depending on the alloy composition. Columnar grains coexisting with globular grains were found in the AZ31 and ZX11 alloys, whereas the ZWK200 alloy showed a homogeneous fine-grained microstructure characterized by a weaker texture even at the highest TRC speed used. While there is a tendency to reduce the centerline segregation as the TRC speed is decreased during casting of the AZ31 alloy, the formation of this defect cannot be prevented in the ZX11 and ZWK200 alloys by only varying the TRC speed.

Motion and Distribution of Floating Grain in Direct-Chill Casting of Aluminum Alloys: Experiments and Numerical Modeling

Sedimentation of free-floating grains is the main origin of the negative centerline segregation in direct-chill casting of aluminum alloys. This study examines the motion and distribution of the floating grains during casting using experimental measurements and numerical modeling. The typical floating grains consisting of interior solute-lean coarse dendrites and periphery fine dendrites were experimentally observed only in the central region of the billet along with the negative segregation. The billet exhibits the strongest segregation at the center where the most floating grains are found. In simulations, under the action of the convection and the underlying forces, the grains floating in the transition region exhibit different motion behaviors, i.e., settling to the mushy zone, floating in the slurry zone, and moving upward to the liquid zone. However, most grains were transported to the central region of the billet and then were captured by the mushy zone and settled. Therefore, the floating grains comprise the largest share of the grain structure at the center of the billet, in agreement with the experimental results. Moreover, the simulation results indicate that the increased size of the grains promotes the sedimentation of the floating grains. These results are important for the future alleviation of negative centerline segregation in direct-chill casting of aluminum alloys.

Controlling Variability in Mechanical Properties of Plates by Reducing Centerline Segregation to Meet Strain-Based Design of Pipeline Steel

Low variability in mechanical properties is required for pipeline project designs to meet a strain-based design, which is used in regions of large ground movements. The objective of this study is to elucidate the influence of centerline segregation in continuously cast slab on variability in the mechanical property of pipeline steel, and controlling centerline segregation can meet the requirements of a strain-based design. Mannesmann rating method was used to evaluate the degree of segregation of two slabs and its effect on variability in mechanical properties of corresponding plates. Microstructural characterization indicated that bainite/martensite was formed in a segregated area where the content of C and Mn enriched. The mechanical property results indicated that controlling the degree of centerline segregation can reduce tensile strength variability and improve ductile-brittle transition temperature (DBTT).