Evaluation of AccuFIT 9000: A Novel Apparatus for Quantitative Fit Testing of Particulate Respirators

Various strategies developed for protecting frontline workers and the general public from the novel coronavirus, SARS-CoV-2, largely rely on respiratory protective devices (RPDs), especially considering recent evidence about the aerosol transmission route of COVID-19. Performance of an RPD primarily depends on how well the protective device fits the wearer. Therefore, quantitative fit testing of particulate respirators is crucial for achieving the intended protection level. Millions of fit tests are conducted every year using a US OSHA-accepted standard protocol involving a PortaCount® (TSI Inc., Shoreview, MN, USA) which measures a respirator fit factor. Recently, several alternative fit testing instruments have been developed and introduced to the market. Among them is an AccuFIT 9000 (Kanomax-Japan Inc., Suita-city, Osaka, Japan), which, like the PortaCount®, utilizes the condensation particle counting principle, but features an advanced saturation chamber design allowing for a longer residence time and greater flow stability. It is also claimed to have a more cost-efficient assembly than its predecessors. In this study, the novel AccuFIT apparatus was extensively evaluated against the PortaCount® (the reference instrument) using the traditional standard fit testing protocol and following the American National Standards Institute (ANSI) standard (Z88.10-2010 Annex A2). The evaluation was performed with three types of respirators, N95 filtering facepiece respirator (FFR), P100 FFR, and half-mask elastomeric facepiece, of different models and manufacturers donned on 25 subjects. The comparative testing and analysis showed that the AccuFIT 9000 is capable of identifying an inadequate fit of the tested respirators with a sensitivity 0.95 and specificity of 0.97, which meets the ANSI requirement of ≥0.95. The other ANSI requirements/recommendations were also met. It was concluded that the novel fit testing apparatus demonstrated an acceptable performance and, thus, can be successfully deployed for the quantitative respirator fit testing.

Experimental characterization of the COndensation PArticle counting System for high altitude aircraft-borne application

A characterization of the ultra-fine aerosol particle counter COPAS (COndensation PArticle counting System) for operation on board the Russian high altitude research aircraft M-55 Geophysika is presented. The COPAS instrument consists of an aerosol inlet and two dual-channel continuous flow Condensation Particle Counters (CPCs) operated with the chlorofluorocarbon FC-43. It operates at pressures between 400 and 50 hPa for aerosol detection in the particle diameter (dp) range from 6 nm up to 1 μm. The aerosol inlet, designed for the M-55, is characterized with respect to aspiration, transmission, and transport losses. The experimental characterization of counting efficiencies of three CPCs yields dp50 (50% detection particle diameter) of 6 nm, 11 nm, and 15 nm at temperature differences (ΔT) between saturator and condenser of 17°C, 30°C, and 33°C, respectively. Non-volatile particles are quantified with a fourth CPC, with dp50=11 nm. It includes an aerosol heating line (250°C) to evaporate H2SO4-H2O particles of 11 nm<dp<200 nm at pressures between 70 and 300 hPa. An instrumental in-flight inter-comparison of the different COPAS CPCs yields correlation coefficients of 0.996 and 0.985. The particle emission index for the M-55 in the range of 1.4–8.4×1016 kg−1 fuel burned has been estimated based on measurements of the Geophysika's own exhaust.

Experimental characterization of the COndensation PArticle counting System for high altitude aircraft-borne application

This study aims at a detailed characterization of an ultra-fine aerosol particle counting system for operation on board the Russian high altitude research aircraft M-55 "Geophysica" (maximum ceiling of 21 km). The COndensation PArticle counting Systems (COPAS) consists of an aerosol inlet and two dual-channel continuous flow Condensation Particle Counters (CPCs). The aerosol inlet, adapted for COPAS measurements on board the M-55 "Geophysica", is described concerning aspiration, transmission, and transport losses. The counting efficiencies of the CPCs using the chlorofluorocarbon FC-43 as the working fluid are studied experimentally at two pressure conditions, 300 hPa and 70 hPa. Three COPAS channels are operated with different temperature differences between the saturator and the condenser block yielding smallest detectable particle sizes (dp50 – as 50% detection "cut off" diameters) of 6 nm, 11 nm, and 15 nm, respectively, at ambient pressure of 70 hPa. The fourth COPAS channel is operated with an aerosol heating line (250°C) for a determination of the non-volatile number of particles. The heating line is experimentally proven to volatilize pure H2SO4-H2O particles for a particle diameter (dp) range of 11 nm<dp<200 nm. Additionally this study includes investigation to exclude auto-nucleation of the working fluid inside the CPCs. An instrumental inter-comparison (cross-correlation) has been performed for several measurement flights and mission flights in the Arctic and the Tropics are discussed. Finally, COPAS measurements are used for an aircraft plume crossing analysis.