Tidally Driven Dispersion of a Deep-Sea Sediment Plume Originating from Seafloor Disturbance in the DISCOL Area (SE-Pacific Ocean)

The purpose of the study was to measure in situ the background suspended particulate matter concentration (SPMC) in the DISCOL area (SE Pacific) and its increase due to mechanical mobilization of the seabed. The disturbance experiment imitated future manganese nodule exploitations and was designed to measure the sediment plume generated by such activities. In the direct vicinity of the disturbance, landers equipped with acoustic and optical sensors measured the current velocities and the SPMC. The SPMC at the disturbance was easily up to 10 mg/L and thus about 200 times higher than the background concentration. The downstream sediment plume, measured by the lander, had a SPMC of about 1 mg/L. After tide reversal, the sediment plume was recorded a second time. A sediment transport model reproduced the plume dispersion. After rapid settling of the coarser fraction, a plume of hardly settling fine particles remained in suspension (and no deposition–resuspension cycles). The transport was controlled by the tides and by the vertical velocity component that resulted from bathymetrical differences. The plume may continue to disperse up to 100+ days (up to hundreds of km) depending on the particle size and until background concentration is reached.

Analysis of Thermal Plume Dispersion into the Sea by Remote Sensing and Numerical Modeling

The aim of this work was to study, by remote sensing and numerical modeling, the thermal dispersion of a plume discharged into the sea by a nuclear power plant. The case study is the thermal discharge of the Laguna Verde nuclear power plant, located on the coast of the Gulf of Mexico. First, the thermal plume dispersion was characterized by applying remote sensing for different scenarios. Afterwards, Delft3D-FLOW numerical simulations were performed to expand the analysis of the thermal processes for a case in which the thermal plume tends towards the intake of the power plant. This thermal analysis was carried out by comparing the behavior of different dimensionless parameters. Moreover, the results of the numerical simulations were used to investigate the performance of the AEM and the k-L and k-ε turbulence models, available in the Delft3D-FLOW model. An LES turbulence model contribution was also analyzed. The results show that forced convection is predominant near the plume discharge area and at the vicinity of the intake structure. According to the metrics calculated, all turbulence models produced good agreement with the remote sensing data, except when the LES scheme was considered. Finally, the use of remote sensing and numerical simulations is helpful to better understand thermal plume dispersion.

Microwave Limb Sounder (MLS) observations of biomass burning products in the stratosphere from Canadian forest fires in August 2017

Forest fires in British Columbia in August 2017 caused a pyrocumulonimbus event that injected a polluted air mass into the lower stratosphere. The Microwave Limb Sounder (MLS) on the Aura satellite first observed the polluted air mass on 14 August 2017 and continued to observe it for 60 d (100 d in water vapour). We estimate the mass of CO injected into the stratosphere to be 2400 Gg. Events in which a fire injects its burning products directly into the stratosphere are rare: this is the third of four such events in the 16 years since the launch of Aura, the second largest of the four events, and the only one in the Northern Hemisphere. The other three events occurred in Australia in December 2006, February 2009 and from December 2019 to January 2020. Unlike the 2006 and 2009 events, but like the 2019–2020 event, the polluted air mass described here had a clearly elevated water vapour content: between 2.5 and 5 times greater than that in the surrounding atmosphere. We describe the evolution of the polluted air mass, showing that it rose to an altitude of about 24 km (31 hPa) and divided into several identifiable parts. In addition to CO and H2O, we observe enhanced amounts of HCN, CH3CN, CH3Cl and CH3OH with mixing ratios in the range to be expected from a variety of measurements in other biomass burning plumes. We use back trajectories and plume-dispersion modelling to demonstrate that the pollutants observed by MLS originated in the British Columbia fires, the likeliest source being at 53.2∘ N, 121.8∘ W at 05:20 UTC on 13 August 2017.

Assessing representativity of NH₃ measurements influenced by boundary-layer dynamics and turbulent dispersion of a nearby emission source

This study presents a fine scale simulation approach to assess the representativity of ammonia (NH3) measurements in proximity of an emission source. Close proximity to emission sources (< 5 km) can introduce a bias in regionally representative measurements of the NH3 molar fraction and flux. Measurement sites should therefore be located a significant distance from emission sources, but such requirements are poorly defined and can be difficult to meet in densely agricultural regions. This study presents a consistent criterium to assess the regional representativity of NH3 measurements in proximity of an emission source, calculating variables that quantify the NH3 plume dispersion using a series of numerical experiments at a fine resolution (20 m). Our fine scale simulation framework with explicitly resolved turbulence enables us to distinguish between the background NH3 and the emission plume, including realistic representations of NH3 deposition and chemical gas-aerosol transformations. We introduce the concept of blending-distance, based on the calculation of turbulent fluctuations, to systematically analyze the impact of the emission plume on simulated measurements, relative to this background NH3. This sensitivity analysis includes systematic experiments varying meteorological factors, emission/deposition and NH3 dependences. Considering these sensitivities, we find that NH3 measurements should be located at a minimum distance of 0.5–2.5 km and 1–3.5 km from an emission source, for NH3 molar fraction and flux measurements respectively. The simulation framework presented here can easily be adapted to local conditions and paves the way for future ammonia research at high spatio-temporal resolution.

Technical note: Interpretation of field observations of point-source methane plume using observation-driven large-eddy simulations

This study demonstrates the ability of large-eddy simulation (LES) forced by a large-scale model to reproduce plume dispersion in an actual field campaign. Our aim is to bring together field observations taken under non-ideal conditions and LES to show that this combination can help to derive point source strengths from sparse observations. We prepared a one-day case study based on data collected near an oil well during the ROMEO campaign (ROmanian Methane Emissions from Oil and gas) that took place in October 2019. We set up our LES using boundary conditions derived from the meteorological reanalysis ERA5 and released a point source in line with the configuration in the field. The weather conditions produced by the LES show close agreement with field observations, although the observed wind field showed complex features due to the absence of synoptic forcing. In order to align the plume direction with field observations, we created a second simulation experiment with manipulated wind fields. The estimated source strengths using the LES plume agrees well with the emitted artificial tracer gas plume, indicating the suitability of LES to infer source strengths from observations under complex conditions. To further harvest the added value of LES, higher order statistical moments of the simulated plume were analysed. Here, we found good agreement with plumes from previous LES and laboratory experiments in channel flows. We derived a length scale of plume mixing from the boundary layer height, the mean wind speed and convective velocity scale. It was demonstrated that this length scale represents the distance from the source at which the predominant plume behaviour transfers from meandering dispersion to relative dispersion.

Mobile atmospheric measurements and local-scale inverse estimation of the location and rates of brief CH₄ and CO₂ releases from point sources

We present a local-scale atmospheric inversion framework to estimate the location and rate of methane (CH4) and carbon dioxide (CO2) releases from point sources. It relies on mobile near-ground atmospheric CH4 and CO2 mole fraction measurements across the corresponding atmospheric plumes downwind of these sources, on high-frequency meteorological measurements, and on a Gaussian plume dispersion model. The framework exploits the scatter of the positions of the individual plume cross sections, the integrals of the gas mole fractions above the background within these plume cross sections, and the variations of these integrals from one cross section to the other to infer the position and rate of the releases. It has been developed and applied to provide estimates of brief controlled CH4 and CO2 point source releases during a 1-week campaign in October 2018 at the TOTAL experimental platform TADI in Lacq, France. These releases typically lasted 4 to 8 min and covered a wide range of rates (0.3 to 200 g CH4/s and 0.2 to 150 g CO2/s) to test the capability of atmospheric monitoring systems to react fast to emergency situations in industrial facilities. It also allowed testing of their capability to provide precise emission estimates for the application of climate change mitigation strategies. However, the low and highly varying wind conditions during the releases added difficulties to the challenge of characterizing the atmospheric transport over the very short duration of the releases. We present our series of CH4 and CO2 mole fraction measurements using instruments on board a car that drove along roads ∼50 to 150 m downwind of the 40 m × 60 m area for controlled releases along with the estimates of the release locations and rates. The comparisons of these results to the actual position and rate of the controlled releases indicate ∼10 %–40 % average errors (depending on the inversion configuration or on the series of tests) in the estimates of the release rates and ∼30–40 m errors in the estimates of the release locations. These results are shown to be promising, especially since better results could be expected for longer releases and under meteorological conditions more favorable to local-scale dispersion modeling. However, the analysis also highlights the need for methodological improvements to increase the skill for estimating the source locations.

Numerical Simulation of Deep-Sea Sediment Transport Induced by a Dredge Experiment in the Northeastern Pacific Ocean

Predictability of the dispersion of sediment plumes induced by potential deep-sea mining activities is still very limited due to operational limitations on in-situ observations required for a thorough validation and calibration of numerical models. Here we report on a plume dispersion experiment carried out in the German license area for the exploration of polymetallic nodules in the northeastern tropical Pacific Ocean in 4,200 m water depth. The dispersion of a sediment plume induced by a small-scale dredge experiment in April 2019 was investigated numerically by employing a sediment transport module coupled to a high-resolution hydrodynamic regional ocean model. Various aspects including sediment characteristics and ocean hydrodynamics were examined to obtain the best statistical agreement between sensor-based observations and model results. Results show that the model is capable of reproducing suspended sediment concentration and redeposition patterns observed during the dredge experiment. Due to a strong southward current during the dredging, the model predicts no sediment deposition and plume dispersion north of the dredging tracks. The sediment redeposition thickness reaches up to 9 mm directly next to the dredging tracks and 0.07 mm in about 320 m away from the dredging center. The model results suggest that seabed topography and variable sediment release heights above the seafloor cause significant changes especially for the low sedimentation pattern in the far-field area. Near-bottom mixing is expected to strongly influence vertical transport of suspended sediment.

Large-Eddy Simulation of Plume Dispersion in the Central District of Oklahoma City by Coupling with a Mesoscale Meteorological Simulation Model and Observation

Contaminant gas dispersion within an urban area resulting from accidental or intentional release is of great concern to public health and social security. When estimating plume dispersion in a built-up urban area under real meteorological conditions by computational fluid dynamics (CFD), a crucial issue is how to prescribe the input conditions. There are typically two approaches: using the outputs of a mesoscale meteorological simulation (MMS) model and meteorological observations (OBS). However, the influences of the different approaches on the simulation results have not been fully demonstrated. In this study, we conducted large-eddy simulations (LESs) of plume dispersion in the urban central district of Oklahoma City under real meteorological conditions by coupling with a MMS model and OBS obtained at a single stationary point, and evaluated the two different coupling simulations in comparison with the field experiments. The LES–MMS coupling showed better performance than the LES–OBS one. The latter one also showed a reasonable performance comparable to the acceptance criteria on the model prediction within a factor of two of the experimental data. These facts indicate that the approach using observations at a single stationary point still has enough potential to drive CFD models for plume dispersion under real meteorological conditions.