scholarly journals Stress-Strain Behavior and Microstructure Change of Type 304 Stainless Steel under Tension and Compression

2014 ◽  
Vol 55 (642) ◽  
pp. 615-619 ◽  
Author(s):  
Eiichiro ISHIMARU ◽  
Hiroshi HAMASAKI ◽  
Tatsuya OHNO ◽  
Fusahito YOSHIDA
Keyword(s):  
Stainless Steel ◽  
304 Stainless Steel ◽  
Stress Strain ◽  
Microstructure Change ◽  
Strain Behavior ◽  
Tension And Compression ◽  
Change Of Type ◽  
Type 304 ◽  
Type 304 Stainless Steel

Flow Stress Equations for Type 304 Stainless and AISI 1055 Steels

1985 ◽  
Vol 107 (2) ◽  
pp. 97-100 ◽  
Author(s):  
P. Dadras
Keyword(s):  
Experimental Data ◽  
Stainless Steel ◽  
Flow Stress ◽  
Strain Rate ◽  
Working Conditions ◽  
Hot Working ◽  
304 Stainless Steel ◽  
Strain Behavior ◽  
Type 304 ◽  
Type 304 Stainless Steel

A model for stress-strain behavior under hot working conditions has been proposed. Based on experimental data, equations for the dependence of flow stress on strain, strain rate, and temperature have been developed. Application to type 304 stainless steel and AISI 1055 steel has been demonstrated.

High-Cycle Fatigue Behavior of Solution-Annealed and Thermally-Aged Type 304 Stainless Steel

1980 ◽  
Vol 102 (1) ◽  
pp. 141-146 ◽  
Author(s):  
P. Soo ◽  
J. G. Y. Chow
Keyword(s):  
Stainless Steel ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Cyclic Stress ◽  
304 Stainless Steel ◽  
Strain History ◽  
Cycle Fatigue ◽  
Stress Strain ◽  
Type 304 ◽  
Type 304 Stainless Steel

High-cycle, load-controlled fatigue data have been obtained for solution-annealed and thermally-aged Type 304 stainless steel, for temperatures between 22 and 593°C (72-1100°F) at a cycling rate of 40 Hz. Although these data are principally used to assess fatigue failure in components subjected to rapid stress cycling, it has been shown that they may be correlated with available low-cycle data if cyclic stress-strain curves are used for converting the high-cycle stresses to effective strains. Differences in initial stress-strain history and cycling rates for the high- and low-cycle data evaluated are found to be unimportant. For the thermally-aged material there is an initial enhancement of the high-cycle-fatigue strength but, after long aging times, the strength decreases to a value close to that for unaged material. The carbide precipitates formed during aging appear to influence fatigue life through changes they impart in the cyclic work-hardening rates.

A Simple Model for Stable Cyclic Stress-Strain Relationship of Type 304 Stainless Steel Under Nonproportional Loading

1999 ◽  
Vol 122 (1) ◽  
pp. 1-9 ◽  
Author(s):  
Takamoto Itoh ◽  
Xu Chen ◽  
Toshimitsu Nakagawa ◽  
Masao Sakane
Keyword(s):  
Stainless Steel ◽  
Cyclic Stress ◽  
304 Stainless Steel ◽  
Surface Model ◽  
Stress Strain ◽  
Nonproportional Loading ◽  
Strain Relationship ◽  
Strain Paths ◽  
Type 304 ◽  
Type 304 Stainless Steel

This paper proposes a simple two-surface model for cyclic incremental plasticity based on combined Mroz and Ziegler kinematic hardening rules under nonproportional loading. The model has only seven material constants and a nonproportional factor which describes the degree of additional hardening. Cyclic loading experiments with fourteen strain paths were conducted using Type 304 stainless steel. The simulation has shown that the model was precise enough to calculate the stable cyclic stress-strain relationship under nonproportional loadings. [S0094-4289(00)00101-8]

scholarly journals Finite Element Modelling of Cold Formed Stainless Steel Columns

10.14311/722 ◽  
2005 ◽  
Vol 45 (3) ◽  
Author(s):  
M. Macdonald ◽  
J. Rhodes
Keyword(s):  
Finite Element ◽  
Stainless Steel ◽  
Load Capacity ◽  
304 Stainless Steel ◽  
Channel Cross Section ◽  
Stress Strain ◽  
Steel Columns ◽  
Strain Behaviour ◽  
Type 304 ◽  
Type 304 Stainless Steel

This paper describes the results obtained from a finite element investigation into the load capacity of column members of lipped channel cross-section, cold formed from Type 304 stainless steel, subjected to concentric and eccentric compression loading. The main aims of this investigation were to determine the effects which the non-linearity of the stress-strain behaviour of the material would have on the column behaviour under concentric or eccentric loading. Stress-strain curves derived from tests and design codes are incorporated into non-linear finite element analyses of eccentrically loaded columns and the results obtained are compared with those obtained on the basis of experiments on stainless steel channel columns with the same properties and dimensions. Comparisons of the finite element results and the test results are also made with existing design specifications and conclusions are drawn on the basis of the comparisons. 

OUTOKUMPU TYPE 630

Alloy Digest ◽  
2016 ◽  
Vol 65 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
High Performance ◽  
High Strength ◽  
Heat Treating ◽  
304 Stainless Steel ◽  
Type 304 ◽  
Type 304 Stainless Steel

Abstract Outokumpu Type 630 is a martensitic age hardenable alloy of composition 17Cr-4Ni. The alloy has high strength and corrosion resistance similar to that of Type 304 stainless steel. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-1238. Producer or source: Outokumpu High Performance Stainless.

Passivity of Type 304 Stainless Steel–Effect of Plastic Deformation

CORROSION ◽  
1972 ◽  
Vol 28 (7) ◽  
pp. 269-273 ◽  
Author(s):  
K. Elayaperumal ◽  
P. K. De ◽  
J. Balachandra
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
304 Stainless Steel ◽  
Type 304 ◽  
Type 304 Stainless Steel
Sign in / Sign up

Export Citation Format

Share Document