scholarly journals THE CLAMP-ON WAVE FORCE METER

2011 ◽  
Vol 1 (7) ◽  
pp. 39
Author(s):  
Lars Skjelbreia
Keyword(s):  
Gulf Of Mexico ◽  
Water Depth ◽  
Wave Force ◽  
Wave Forces ◽  
Oil Well ◽  
Great Effort ◽  
Oil Companies ◽  
Research Corporation ◽  
Cylindrical Piles ◽  
Different Diameters

Because of the tremendous increase in offshore activities, a great effort has been made on obtaining information on wave forces on structural members. Several oil companies have invested large sums of money in the design and construction of full-scale systems for measuring the wave forces. The equipment used for measuring the forces have been single cantilevers or segmented piles designed to make discrete measurements along the pile. For instance, during the last five years, The California Company and California Research Corporation (subsidiaries of Standard Oil Company of California) operated an installation in the Gulf of Mexico with four segmented piles of different diameters. The wave forces were measured by three-foot high force dynamometers located at seven different elevations along the length of each test pile. Each dynamometer was constructed from a section of the cylindrical pile which was attached to a system of flexures on the inside. So far the wave forces have been measured on cylindrical piles varying in diameter from one to four feet and in water depths varying from 30 to 50 feet. As the pile diameter and water depth increase, however, the measurements of wave forces by use of a cantilever or a segmented pile become very difficult and expensive. Therefore, a need exists for investigating other means for measuring the wave forces on a pile. This paper will describe the design and operation of a force meter that may be clamped to an existing pile. In Spring 1960, California Research Corporation installed equipment incorporating eight of the clamp-on meters on an oil well drilling platform in the Gulf of Mexico. The water depth at the location is 100 feet, and two years of operation are planned.

Application of a Hybrid Boussinesq-Panel Model for Motion Predictions of a Moored Sevan-Floater in Finite Water Depth

2017 ◽  
Author(s):  
Jikun You ◽  
Einar Bernt Glomnes
Keyword(s):  
Water Depth ◽  
Low Frequency ◽  
Boussinesq Equations ◽  
Wave Force ◽  
Irregular Waves ◽  
Wave Forces ◽  
Rankine Source ◽  
Panel Model ◽  
Finite Water Depth ◽  
Incident Waves

This paper presents the applications of an efficient hybrid time-domain simulation model for predicting moored Sevan-floater motions in irregular waves and finite water depth. The irregular incident waves are modeled by the extended Boussinesq equations, which can capture wave-wave interactions and the low-frequency long waves accurately in finite and shallow water depth. By imposing the incident wave kinematics on the surface of the floater, a panel model based on Rankine source method is applied for the calculation of wave forces and corresponding floater motions. The contributions from low-frequency components in incident waves as well as their diffraction effects are included in the wave force calculations. Validation of the irregular waves simulated by the present numerical model are performed against experimental data. Then, the simulated moored floater motions are compared with model test results and results based on Newman’s approximation. The general good agreements with experimental results demonstrate the present model can be used as an alternative for this problem while Newman’s approximation shows non-conservative results.

Calculation of Wave Forces on Cylindrical Piles Using a 3D Numerical Wave Tank

2013 ◽  
Author(s):  
Arun Kamath ◽  
Hans Bihs ◽  
Øivind A. Arntsen
Keyword(s):  
Numerical Model ◽  
Stokes Equations ◽  
Practical Interest ◽  
Vertical Cylinder ◽  
Free Water ◽  
Wave Force ◽  
Weno Scheme ◽  
Wave Forces ◽  
Single Cylinder ◽  
Cylindrical Piles

Offshore constructions generally include a large number of vertical cylinders in the support structure. The calculation of wave forces on a vertical cylinder and hydrodynamic effects on it in the presence of neighbouring cylinders is of practical interest. In this paper, a 3D numerical model is used to calculate wave forces on bottom fixed cylindrical piles. Two cases are considered in this study: a single cylinder and a pair of tandem cylinders. A scenario with multiple cylindrical structures in close proximity introduces complex wave-structure interactions and would be of great interest to observe this in detail in a three-dimensional simulation. The wave force exerted on a cylindrical pile is numerically calculated by integrating the pressure and the wall shear stress around the surface of the cylinder. In the case of the single cylinder, the force calculated by the model is compared to the force predicted by the Morison formula and MacCamy-Fuchs theory. In the second case, the pair of cylinders is aligned in the direction of the incoming waves. The numerically calculated inline wave force on each cylinder is compared to the analytical solution for this setup and a good agreement is seen. The Reynolds-Averaged Navier-Stokes equations are used as the governing equations for the fluid flow in the numerical model. The convective terms are discretized using a 5th-order conservative finite difference WENO scheme. A 3rd-order accurate TVD Range-Kutta scheme is used for time discretization. Chorin’s projection method is used to discretize the pressure. The Poisson equation for pressure is solved using a preconditioned BiCGStab algorithm. The level set method is used to obtain a sharp representation of the free water surface. Turbulence in the flow is simulated using the k-ω model. The numerical model is adapted to parallel processing using the MPI library to improve the computing performance of the code.

The Concept of the Optimum Alignment of Discharge Pipelines Due to the Minimization of the Wave Forces

1992 ◽  
Vol 25 (9) ◽  
pp. 211-216
Author(s):  
A. Akyarli ◽  
Y. Arisoy
Keyword(s):  
Wave Height ◽  
Wave Force ◽  
Wave Forces ◽  
Wave Direction ◽  
Incoming Wave ◽  
Pipeline Route ◽  
Optimum Alignment ◽  
The Cost ◽  
Resultant Wave

As the wave forces are the function of the wave height, period and the angle between the incoming wave direction and the axis of the discharge pipeline, the resultant wave force is directly related to the alignment of the pipeline. In this paper, a method is explained to determine an optimum pipeline route for which the resultant wave force becomes minimum and hence, the cost of the constructive measures may decrease. Also, the application of this method is submitted through a case study.

scholarly journals Characteristics of Breaking Wave Forces on Piles over a Permeable Seabed

2021 ◽  
Vol 9 (5) ◽  
pp. 520
Author(s):  
Zhenyu Liu ◽  
Zhen Guo ◽  
Yuzhe Dou ◽  
Fanyu Zeng
Keyword(s):  
Wave Breaking ◽  
Stokes Equations ◽  
Slope Angle ◽  
Wave Force ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Secondary Wave ◽  
Wave Forces ◽  
Breaking Wave ◽  
Breaking Wave Forces

Most offshore wind turbines are installed in shallow water and exposed to breaking waves. Previous numerical studies focusing on breaking wave forces generally ignored the seabed permeability. In this paper, a numerical model based on Volume-Averaged Reynolds Averaged Navier–Stokes equations (VARANS) is employed to reveal the process of a solitary wave interacting with a rigid pile over a permeable slope. Through applying the Forchheimer saturated drag equation, effects of seabed permeability on fluid motions are simulated. The reliability of the present model is verified by comparisons between experimentally obtained data and the numerical results. Further, 190 cases are simulated and the effects of different parameters on breaking wave forces on the pile are studied systematically. Results indicate that over a permeable seabed, the maximum breaking wave forces can occur not only when waves break just before the pile, but also when a “secondary wave wall” slams against the pile, after wave breaking. With the initial wave height increasing, breaking wave forces will increase, but the growth can decrease as the slope angle and permeability increase. For inclined piles around the wave breaking point, the maximum breaking wave force usually occurs with an inclination angle of α = −22.5° or 0°.

Ocean Wave Forces on Circular Cylindrical Piles

1957 ◽  
Vol 83 (2) ◽  
Author(s):  
R. L. Wiegel ◽  
K. E. Beebe ◽  
James Moon
Keyword(s):  
Ocean Wave ◽  
Wave Forces ◽  
Cylindrical Piles

scholarly journals WAVE ACTION ON LARGE OFF-SHORE STRUCTURES

1976 ◽  
Vol 1 (15) ◽  
pp. 129 ◽  
Author(s):  
C.J. Apelt ◽  
A. Macknight
Keyword(s):  
Numerical Methods ◽  
Water Surface ◽  
Theoretical Method ◽  
Wave Force ◽  
Wave Action ◽  
Tidal Range ◽  
Scale Model ◽  
Wave Forces ◽  
Accurate Calculation ◽  
Scour Protection

The paper describes investigations carried out in order to design for the wave action, both wave force and scour, on large off-shore berthing structures sited approximately 1.3 miles (2.1 km) off-shore near Hay Point, North Queensland, in 56 feet (17 m) of water at low tide, the tidal range being 20 feet (6 m). The region is a cyclone area and the structures must be capable of withstanding attack from maximum predicted waves with period of 8.25 seconds and amplitude of 24 feet (7.3 m). The main units in the berthing structures are concrete caissons sunk on to the ocean bed and the largest of these have plan dimensions of approximately 150 feet (46.7 m) by 135 feet (41.4 m) with four columns approximately 40 feet (12.2 m) square projecting through the water surface. No theoretical method available at the time of the investigation was capable of accurate calculation of wave forces on these structures. A scale model was tested to obtain wave forces and the paper compares results from the model with those of numerical methods and discusses the application of the results to the design functions. Scour effects were also modelled and the results used as the basis for design of scour protection.

Experimental Study of Wave Force Distribution on a Monopile Structure

2018 ◽  
Author(s):  
Malene H. Vested ◽  
Stefan Carstensen ◽  
Erik Damgaard Christensen
Keyword(s):  
Experimental Studies ◽  
Cost Effective ◽  
Wave Force ◽  
Offshore Wind ◽  
Irregular Waves ◽  
Force Distribution ◽  
Wave Forces ◽  
Total Force ◽  
Wave Flume ◽  
Effective Manner

As the demand for offshore wind energy continues to grow, the strive to understand the wave forces acting on the substructure of the wind turbines continues. In regard to wind turbine design, it is vital to consider not only the total wave force, but also the local wave forces. Local forces are particularly important for the design of secondary structures as e.g. mooring platforms. Typically, however, experimental studies mainly concern total forces or idealized local forces. We present here a rather simple way to measure local forces along a model monopile. The study is conducted in a wave flume of 28 m in length, in which waves are generated by a piston-type wave maker at a water depth of 0.515 m and shoal onto a bed of slope 1:25. A model monopile is installed and subjected to forcing from a series of both regular and irregular waves. In the experimental set-up, the model monopile is fixed at the bottom and the top and consists of seven independent cylindrical sections. The cylindrical sections are connected by force transducers which measure local shear, and so the associated local forces may be determined. The measured local forces are compared to the force distribution given by Morisons equation combined with linear theory and Wheeler stretching, which is a force estimate commonly used in the industry. This study shows that the total force is rather well captured by Morison’s equation. The force distribution estimated from Morison’s equation, however, shows larger discrepancies from the measured forces. This encourages for further measurements. In this study, we show that it is possible to measure force distribution on a model monopile in a simple and cost-effective manner. The aim is here to demonstrate the method and we will later present a larger body of work associated with the outcome of the measurements.

Wet Tree Semi-Submersible With SCRs for 4,000 ft Water Depth in the Gulf of Mexico

2011 ◽  
Author(s):  
Jingyun Cheng ◽  
Peimin Cao ◽  
Sherry Xiang
Keyword(s):  
Gulf Of Mexico ◽  
Water Depth ◽  
Cost Effective ◽  
Integrated System ◽  
Fatigue Performance ◽  
Strength Performance ◽  
Field Development ◽  
Vessel Motion ◽  
Optimum Solution ◽  
Mitigation Methods

This paper presents a design of a deep draft wet tree semi-submersible with steel catenary risers (SCRs) for 4,000 ft water depth in the Gulf of Mexico (GoM). The integrated system of hull, mooring, and SCRs is discussed. The design challenges of SCRs are highlighted and results of SCR strength and fatigue performance are presented. A comparison study on strength performance of various types of risers under the GoM environment criteria is performed. The assessment of extreme strength responses from various riser and hull configurations provide guidelines for the best hull selection. Sour service requirement creates challenges in the fatigue design of the production riser system at such water depth. Integrated mooring and riser design provides an optimum solution. It’s found that the majority of riser fatigue damage at touch down zone is generated by wave loading & resultant vessel motion and vortex induced vessel motion (VIM). Several fatigue mitigation methods are suggested to improve the riser fatigue performance, such as planned vessel repositioning. The conclusion of this study is that deep draft wet tree semi-submersible with SCRs can be a cost effective solution for field development at 4,000 ft water depth in the Gulf of Mexico.

scholarly journals Wave interaction with Floating platform of different shapes and supports using BEM approach

2017 ◽  
Vol 14 (2) ◽  
pp. 115-133
Author(s):  
Anoop I. Shirkol ◽  
Nasar Thuvanismail
Keyword(s):  
Numerical Model ◽  
Elastic Plate ◽  
Wave Interaction ◽  
Wave Force ◽  
Ocean Waves ◽  
Wave Forces ◽  
Thin Elastic Plate ◽  
Floating Platform ◽  
Floating Elastic Plate ◽  
Different Shapes

Wave interaction with a floating thin elastic plate which can be used as floating platform is analyzed using Boundary Element Method (BEM) for different shapes such as rectangular, circular and triangular. Different support conditions are considered and the performance of the floating platform under the action of ocean waves is explored. The study is performed under the assumption of linearized water wave theory and the floating elastic plate is modelled based on the Euler-Bernoulli beam theory. Using Galerkin’s approach, a numerical model has been developed and the hydrodynamic loading on the floating elastic plate of shallow draft (thickness) is investigated. The wave forces are generated by the numerical model for the analysis of the floating plate. The resulting bending moment and optimal deflection due to encountering wave force is analysed. The present study will be helpful in design and analysis of the large floating platform in ocean waves.

Numerical Modelling of Breaking Wave Interaction With a Group of Four Vertical Slender Cylinders in Square Arrangements

2016 ◽  
Author(s):  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Arun Kamath ◽  
Dag Myrhaug ◽  
Øivind Asgeir Arnsten
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Numerical Model ◽  
Numerical Modelling ◽  
Wave Interaction ◽  
Wave Force ◽  
Wave Forces ◽  
Breaking Wave ◽  
Square Configuration ◽  
Breaking Wave Forces

The main purpose of the study is to investigate the breaking wave interaction with a group of four circular cylinders. The physical process of wave breaking involves many parameters and an accurate numerical modelling of breaking waves and the interaction with a structure remain a challenge. In the present study, the open-source (Computational Fluid Dynamics) CFD model REEF3D is used to simulate the breaking wave interaction with the multiple cylinders. The numerical model is based on the incompressible Reynolds Averaged Navier-Stokes (RANS) equations, the level set method for the free surface and the k–ω model for turbulence. The model uses a 5th-order conservative finite difference WENO scheme for the convective discretization and a 3rd-order Runge-Kutta scheme for time discretization. The numerical model is validated with experimental data of large-scale experiments for the free surface elevation and the breaking wave force on a single cylinder. A good agreement is seen between the numerical results and experimental data. Two different configurations with four cylinders are examined: in-line square configuration and diamond square configuration. The breaking wave forces on each cylinder in the group are computed for the two cases and the results are compared with the breaking wave force on a single isolated cylinder. Further, the study investigates the water surface elevations and the free surface flow features around the cylinders. In general, the cylinders in both configurations experience the maximum forces lower than the maximum force on a single cylinder. The results of the present study show that the interference effects from the neighbouring cylinders in a group strongly influence the kinematics around and the breaking wave forces on them.

Sign in / Sign up

Export Citation Format

Share Document