scholarly journals WAVE ACTION ON LARGE OFF-SHORE STRUCTURES

1976 ◽  
Vol 1 (15) ◽  
pp. 129 ◽  
Author(s):  
C.J. Apelt ◽  
A. Macknight
Keyword(s):  
Numerical Methods ◽  
Water Surface ◽  
Theoretical Method ◽  
Wave Force ◽  
Wave Action ◽  
Tidal Range ◽  
Scale Model ◽  
Wave Forces ◽  
Accurate Calculation ◽  
Scour Protection

The paper describes investigations carried out in order to design for the wave action, both wave force and scour, on large off-shore berthing structures sited approximately 1.3 miles (2.1 km) off-shore near Hay Point, North Queensland, in 56 feet (17 m) of water at low tide, the tidal range being 20 feet (6 m). The region is a cyclone area and the structures must be capable of withstanding attack from maximum predicted waves with period of 8.25 seconds and amplitude of 24 feet (7.3 m). The main units in the berthing structures are concrete caissons sunk on to the ocean bed and the largest of these have plan dimensions of approximately 150 feet (46.7 m) by 135 feet (41.4 m) with four columns approximately 40 feet (12.2 m) square projecting through the water surface. No theoretical method available at the time of the investigation was capable of accurate calculation of wave forces on these structures. A scale model was tested to obtain wave forces and the paper compares results from the model with those of numerical methods and discusses the application of the results to the design functions. Scour effects were also modelled and the results used as the basis for design of scour protection.

scholarly journals Review of wave forces on bridge decks with experimental and numerical methods

2021 ◽  
Vol 2 (1) ◽  
Author(s):  
Xuebin Chen ◽  
Zhiwu Chen ◽  
Guoji Xu ◽  
Xianrong Zhuo ◽  
Qinghua Deng
Keyword(s):  
Numerical Methods ◽  
Failure Mechanism ◽  
Bridge Deck ◽  
Numerical Models ◽  
Bridge Decks ◽  
Wave Force ◽  
Wave Forces ◽  
Coastal Zones ◽  
Coastal Bridges ◽  
Bridge Failure

AbstractMassive coastal bridges were damaged in Hurricanes Ivan (2004) and Katrina (2005), and considerable efforts have been devoted to the studies of wave forces acting on bridge decks since then. When the hurricane and tsunamis approach the coastal zones, the mean water level is elevated, making it possible for the incident wave to hit the bridge deck directly. The study of wave force acting on the bridge deck is essential for the investigation of bridge failure mechanism, and a literature review of wave forces with experimental and numerical methods after Hurricanes Ivan and Katrina is presented in this paper. Though the experiments and numerical models can not fully simulate the wave-deck interaction as in realistic conditions, remarkable progress has been achieved, and some significant findings help the researchers to further understand the failure mechanism of the bridge deck. Emphasis is given to the studies that have significantly improved our understanding of the topic. Challenges associated with the existing studies and suggestions for future studies are presented for a deeper understanding of the failure mechanism of the bridge deck, and more countermeasures are expected to protect the bridge deck under extreme wave forces.

Effect of mesh on CFD aerodynamic performances of a container ship

2020 ◽  
Vol 20 (3) ◽  
pp. 343-353
Author(s):  
Ngo Van He ◽  
Le Thi Thai
Keyword(s):  
Water Surface ◽  
Reference Model ◽  
Full Scale ◽  
Scale Model ◽  
Container Ship ◽  
Ansys Fluent ◽  
Remarkable Effect ◽  
Aerodynamic Performances ◽  
Mesh Convergence

In this paper, a commercial CFD code, ANSYS-Fluent has been used to investigate the effect of mesh number generated in the computed domain on the CFD aerodynamic performances of a container ship. A full-scale model of the 1200TEU container ship has been chosen as a reference model in the computation. Five different mesh numbers for the same dimension domain have been used and the CFD aerodynamic performances of the above water surface hull of the ship have been shown. The obtained CFD results show a remarkable effect of mesh number on aerodynamic performances of the ship and the mesh convergence has been found. The study is an evidence to prove that the mesh number has affected the CFD results in general and the accuracy of the CFD aerodynamic performances in particular.

The Concept of the Optimum Alignment of Discharge Pipelines Due to the Minimization of the Wave Forces

1992 ◽  
Vol 25 (9) ◽  
pp. 211-216
Author(s):  
A. Akyarli ◽  
Y. Arisoy
Keyword(s):  
Wave Height ◽  
Wave Force ◽  
Wave Forces ◽  
Wave Direction ◽  
Incoming Wave ◽  
Pipeline Route ◽  
Optimum Alignment ◽  
The Cost ◽  
Resultant Wave

As the wave forces are the function of the wave height, period and the angle between the incoming wave direction and the axis of the discharge pipeline, the resultant wave force is directly related to the alignment of the pipeline. In this paper, a method is explained to determine an optimum pipeline route for which the resultant wave force becomes minimum and hence, the cost of the constructive measures may decrease. Also, the application of this method is submitted through a case study.

scholarly journals Characteristics of Breaking Wave Forces on Piles over a Permeable Seabed

2021 ◽  
Vol 9 (5) ◽  
pp. 520
Author(s):  
Zhenyu Liu ◽  
Zhen Guo ◽  
Yuzhe Dou ◽  
Fanyu Zeng
Keyword(s):  
Wave Breaking ◽  
Stokes Equations ◽  
Slope Angle ◽  
Wave Force ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Secondary Wave ◽  
Wave Forces ◽  
Breaking Wave ◽  
Breaking Wave Forces

Most offshore wind turbines are installed in shallow water and exposed to breaking waves. Previous numerical studies focusing on breaking wave forces generally ignored the seabed permeability. In this paper, a numerical model based on Volume-Averaged Reynolds Averaged Navier–Stokes equations (VARANS) is employed to reveal the process of a solitary wave interacting with a rigid pile over a permeable slope. Through applying the Forchheimer saturated drag equation, effects of seabed permeability on fluid motions are simulated. The reliability of the present model is verified by comparisons between experimentally obtained data and the numerical results. Further, 190 cases are simulated and the effects of different parameters on breaking wave forces on the pile are studied systematically. Results indicate that over a permeable seabed, the maximum breaking wave forces can occur not only when waves break just before the pile, but also when a “secondary wave wall” slams against the pile, after wave breaking. With the initial wave height increasing, breaking wave forces will increase, but the growth can decrease as the slope angle and permeability increase. For inclined piles around the wave breaking point, the maximum breaking wave force usually occurs with an inclination angle of α = −22.5° or 0°.

Scale and Configuration Effects of an Airchamber on PTO of Oscillating Water Column Type Wave Energy Converters

2021 ◽  
Author(s):  
Tomoki Ikoma ◽  
Shota Hirai ◽  
Yasuhiro Aida ◽  
Koichi Masuda
Keyword(s):  
Water Column ◽  
Wave Energy ◽  
Water Surface ◽  
Air Pressure ◽  
Scale Model ◽  
Linear Potential ◽  
Oscillating Water Column ◽  
Wave Energy Converters ◽  
Air Chamber ◽  
Energy Converters

Abstract Wave energy converters (WECs) have been extensively researched. The behaviour of the oscillating water column (OWC) in OWC WECs is extremely complex due to the interaction of waves, air, and turbines. Several problems must be overcome before such WECs can be put to practical use. One problem is that the effect of the difference in scale between a small-scale experimental model and a full-scale model is unclear. In this study, several OWC models with different scales and geometries were used in forced oscillation tests. The wave tank was 7.0 m wide, 24.0 m long, and 1.0 m deep. In the static water experiment, we measured the air pressure and water surface fluctuations in an air chamber. For the experiments, models with a box shape with an open bottom, a manifold shape with an open bottom, and a box shape with a front opening, respectively, were fabricated. Furthermore, 1/1, 1/2, and 1/4 scale models were fabricated for each shape to investigate the effects of scale and shape on the air chamber characteristics. Numerical calculations were carried out by applying linear potential theory and the results were compared with the experimental values. The results confirmed that the air chamber shape and scale affect the air pressure fluctuation and water surface fluctuation inside the OWC system.

Innovative Approach for Use of Hydrofoils on Ultralight Seaplane

2020 ◽  
Author(s):  
Antonio Maglione ◽  
Ubaldo Cella ◽  
Marco E. Biancolini ◽  
Leonardo Lecce
Keyword(s):  
Life Cycle ◽  
Power Plant ◽  
Life Cycle Cost ◽  
Water Surface ◽  
Maintenance Cost ◽  
Wave Forces ◽  
Water Spray ◽  
Sea State ◽  
Important Benefit ◽  
Plant Maintenance

Retractable hydrofoils may enhance performances of seaplane during take-off and landing runs by lowering the speed when the hull is leaving or touching water surface. Hydrofoils are designed to complement airlift with additional hydrodynamic lift elevating the hull above the water at a speed lower than take-off speed; this minimizes slamming phenomenon on the hull, improving seakeeping capability of the seaplane, since water impacts are minimized compared to conventional configuration and, as a consequence, forces and accelerations on airframe, crew and passengers are reduced. This is of foremost importance on ultralight seaplanes, where wave forces acting on the relatively small aircraft mass provide high accelerations and significant roll, pitch and yaw forces that are higher on light aircraft compared to heavy seaplanes. As matter of facts, clear advantage of this configuration is the increase of sea state when a light seaplane can safely fly, providing additional useful days along the year. Important benefit is the improvement of seaplane performances during take-off and landing, reducing duration of the most critical flight phases, increasing overall safety and reducing pilot workload. Further benefits are envisioned, with optimization of wing, empennage and fuselage to minimize aero-drag and, as snow-ball effect, mission fuel consumption and energy power requirements. Life-cycle cost receives benefits too, since less water spray is ingested by engine and less water droplets impinge on fast revolving propeller, thus reducing expensive power plant maintenance cost over the entire service life.

Experimental Study of Wave Force Distribution on a Monopile Structure

2018 ◽  
Author(s):  
Malene H. Vested ◽  
Stefan Carstensen ◽  
Erik Damgaard Christensen
Keyword(s):  
Experimental Studies ◽  
Cost Effective ◽  
Wave Force ◽  
Offshore Wind ◽  
Irregular Waves ◽  
Force Distribution ◽  
Wave Forces ◽  
Total Force ◽  
Wave Flume ◽  
Effective Manner

As the demand for offshore wind energy continues to grow, the strive to understand the wave forces acting on the substructure of the wind turbines continues. In regard to wind turbine design, it is vital to consider not only the total wave force, but also the local wave forces. Local forces are particularly important for the design of secondary structures as e.g. mooring platforms. Typically, however, experimental studies mainly concern total forces or idealized local forces. We present here a rather simple way to measure local forces along a model monopile. The study is conducted in a wave flume of 28 m in length, in which waves are generated by a piston-type wave maker at a water depth of 0.515 m and shoal onto a bed of slope 1:25. A model monopile is installed and subjected to forcing from a series of both regular and irregular waves. In the experimental set-up, the model monopile is fixed at the bottom and the top and consists of seven independent cylindrical sections. The cylindrical sections are connected by force transducers which measure local shear, and so the associated local forces may be determined. The measured local forces are compared to the force distribution given by Morisons equation combined with linear theory and Wheeler stretching, which is a force estimate commonly used in the industry. This study shows that the total force is rather well captured by Morison’s equation. The force distribution estimated from Morison’s equation, however, shows larger discrepancies from the measured forces. This encourages for further measurements. In this study, we show that it is possible to measure force distribution on a model monopile in a simple and cost-effective manner. The aim is here to demonstrate the method and we will later present a larger body of work associated with the outcome of the measurements.

scholarly journals Wave interaction with Floating platform of different shapes and supports using BEM approach

2017 ◽  
Vol 14 (2) ◽  
pp. 115-133
Author(s):  
Anoop I. Shirkol ◽  
Nasar Thuvanismail
Keyword(s):  
Numerical Model ◽  
Elastic Plate ◽  
Wave Interaction ◽  
Wave Force ◽  
Ocean Waves ◽  
Wave Forces ◽  
Thin Elastic Plate ◽  
Floating Platform ◽  
Floating Elastic Plate ◽  
Different Shapes

Wave interaction with a floating thin elastic plate which can be used as floating platform is analyzed using Boundary Element Method (BEM) for different shapes such as rectangular, circular and triangular. Different support conditions are considered and the performance of the floating platform under the action of ocean waves is explored. The study is performed under the assumption of linearized water wave theory and the floating elastic plate is modelled based on the Euler-Bernoulli beam theory. Using Galerkin’s approach, a numerical model has been developed and the hydrodynamic loading on the floating elastic plate of shallow draft (thickness) is investigated. The wave forces are generated by the numerical model for the analysis of the floating plate. The resulting bending moment and optimal deflection due to encountering wave force is analysed. The present study will be helpful in design and analysis of the large floating platform in ocean waves.

Numerical Modelling of Breaking Wave Interaction With a Group of Four Vertical Slender Cylinders in Square Arrangements

2016 ◽  
Author(s):  
Mayilvahanan Alagan Chella ◽  
Hans Bihs ◽  
Arun Kamath ◽  
Dag Myrhaug ◽  
Øivind Asgeir Arnsten
Keyword(s):  
Experimental Data ◽  
Free Surface ◽  
Numerical Model ◽  
Numerical Modelling ◽  
Wave Interaction ◽  
Wave Force ◽  
Wave Forces ◽  
Breaking Wave ◽  
Square Configuration ◽  
Breaking Wave Forces

The main purpose of the study is to investigate the breaking wave interaction with a group of four circular cylinders. The physical process of wave breaking involves many parameters and an accurate numerical modelling of breaking waves and the interaction with a structure remain a challenge. In the present study, the open-source (Computational Fluid Dynamics) CFD model REEF3D is used to simulate the breaking wave interaction with the multiple cylinders. The numerical model is based on the incompressible Reynolds Averaged Navier-Stokes (RANS) equations, the level set method for the free surface and the k–ω model for turbulence. The model uses a 5th-order conservative finite difference WENO scheme for the convective discretization and a 3rd-order Runge-Kutta scheme for time discretization. The numerical model is validated with experimental data of large-scale experiments for the free surface elevation and the breaking wave force on a single cylinder. A good agreement is seen between the numerical results and experimental data. Two different configurations with four cylinders are examined: in-line square configuration and diamond square configuration. The breaking wave forces on each cylinder in the group are computed for the two cases and the results are compared with the breaking wave force on a single isolated cylinder. Further, the study investigates the water surface elevations and the free surface flow features around the cylinders. In general, the cylinders in both configurations experience the maximum forces lower than the maximum force on a single cylinder. The results of the present study show that the interference effects from the neighbouring cylinders in a group strongly influence the kinematics around and the breaking wave forces on them.

Sign in / Sign up

Export Citation Format

Share Document