Database of Sail Shapes vs. Sail Performance and Validation of Numerical Calculation for Upwind Condition

2007 ◽  
Author(s):  
Yutaka Masuyama ◽  
Yusuke Tahara ◽  
Toichi Fukasawa ◽  
Naotoshi Maeda
Keyword(s):  
Numerical Method ◽  
Vortex Lattice ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Numerical Calculations ◽  
Navier Stokes ◽  
Coupling Scheme ◽  
Aerodynamic Coefficients ◽  
Lattice Method ◽  
Cfd Method

Database of full-scale three-dimensional sail shapes are presented with the aerodynamic coefficients for the upwind condition of IMS type sails. Three-dimensional shape data are used for the input of numerical calculations and the results are compared with the measured sail performance. The sail shapes and performance are measured using a sail dynamometer boat Fujin. The Fujin is a 34-foot LOA boat, in which load cells and charge coupled devices (CCD) cameras are installed to measure the sail forces and shapes simultaneously. The sailing conditions of the boat, such as boat speed, heel angle, wind speed, wind angle, and so on, are also measured. The tested sail configurations are as follows: mainsail with 130% jib, mainsail with 75% jib and mainsail alone. Sail shapes are measured at several height positions. The measured shape parameters are chord length, maximum draft, maximum draft position, entry angle at the luff and exit angle at the leech. From these parameters three-dimensional coordinates of the sails are calculated by interpolation. These three-dimensional coordinates are tabulated with the aerodynamic coefficients. Numerical calculations are performed using the measured sail shapes. The calculation methods are of two types; Reynolds-averaged Navier-Stokes (RANS)-based CFD and vortex lattice methods (VLM). A multi-block RANS-based CFD method was developed by one of the authors and is capable of predicting viscous flows and aerodynamic forces for complicated sail configuration for upwind as well as downwind conditions. Important features of the numerical method are summarized as follows: a Finite- Analytic scheme to discretize transport equations, a PISO type velocity-pressure coupling scheme, multi-block domain decomposition capability, and several choices of turbulence models depending on flows of interest. An automatic grid generation scheme is also included. Another calculation method, the vortex lattice method is also adopted. In this case, step-by-step calculations are conducted to attain the steady state of the sail in steady wind. Wake vortices are generated step-by-step, which flow in the direction of the local velocity vector. These calculated sail forces are compared with the measured one, and the validity of the numerical method is studied. The sail shape database and comparison with numerical calculations will provide a good benchmark for the sail performance analysis of the upwind condition of IMS type sails.

3D Simulation of a Convergent-Divergent Aero Engine Intake, Using Two Different CFD Methods

2005 ◽  
Author(s):  
Ioannis Templalexis ◽  
Pericles Pilidis ◽  
Geoffrey Guindeuil ◽  
Theodoros Lekas ◽  
Vassilios Pachidis
Keyword(s):  
Vortex Lattice ◽  
Cfd Simulation ◽  
Three Dimensional ◽  
Internal Flow ◽  
Navier Stokes ◽  
Lattice Method ◽  
Vortex Lattice Method ◽  
Aero Engine ◽  
Flow Effects ◽  
Development And Validation

This study refers to the development and validation of a Three Dimensional (3D) Vortex Lattice Method (VLM) to be used for internal flow case studies and more precisely aero-engine intake simulation. It examines the quantitative and qualitative response of the method to a convergent – divergent intake, produced as a surface of revolution of the CFM56-5B2 upper lip geometry. The study was carried out for three different sections namely: Intake outlet, intake throat and intake inlet. Moreover five different settings of Angle Of Attack (AOA) were considered. The VLM was based on an existing code. It was modified to accommodate internal flow effects and match, as closely as possible, the boundary conditions set by the Reynolds Average Navier-Stokes (RANS) Computational Fluid Dynamics (CFD) simulation. In the context of this study, Vortex Lattice-derived average values velocity profiles were compared against RANS CFD results.

scholarly journals Airflow inside the nasal cavity: visualization using computational fluid dynamics

2010 ◽  
Vol 4 (4) ◽  
pp. 657-661 ◽  
Author(s):  
Mohammed Zubair ◽  
Vizy Nazira Riazuddin ◽  
Mohammed Zulkifly Abdullah ◽  
Rushdan Ismail ◽  
Ibrahim Lutfi Shuaib ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Nasal Cavity ◽  
Three Dimensional ◽  
Clinical Importance ◽  
Navier Stokes ◽  
Tomographic Images ◽  
Computed Tomographic ◽  
Continuity Equations ◽  
Cfd Method

Abstract Background: It is of clinical importance to examine the nasal cavity pre-operatively on surgical treatments. However, there is no simple and easy way to measure airflow in the nasal cavity. Objectives: Visualize the flow features inside the nasal cavity using computational fluid dynamics (CFD) method, and study the effect of different breathing rates on nasal function. Method: A three-dimensional nasal cavity model was reconstructed based on computed tomographic images of a healthy Malaysian adult nose. Navier-Stokes and continuity equations for steady airflow were solved numerically to examine the inspiratory nasal flow. Results: The flow resistance obtained varied from 0.026 to 0.124 Pa.s/mL at flow-rate from 7.5 L/min to 40 L/min. Flow rates by breathing had significant influence on airflow velocity and wall shear-stress in the vestibule and nasal valve region. Conclusion: Airflow simulations based on CFD is most useful for better understanding of flow phenomenon inside the nasal cavity.

Thruster and FPSO Hull Interaction

2014 ◽  
Author(s):  
Ye Tian ◽  
Spyros A. Kinnas
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Computational Efficiency ◽  
Vortex Lattice ◽  
Numerical Results ◽  
Navier Stokes ◽  
Dynamic Positioning ◽  
Lattice Method ◽  
Vortex Lattice Method ◽  
Number Of Cells

A hybrid method which couples a Vortex-Lattice Method (VLM) solver and a Reynolds-Averaged Navier-Stokes (RANS) solver is applied to simulate the interaction between a Dynamic Positioning (DP) thruster and an FPSO hull. The hybrid method could significantly reduce the number of cells to fifth of that in a full blown RANS simulation and thus greatly enhance the computational efficiency. The numerical results are first validated with available experimental data, and then used to assess the significance of the thruster/hull interaction in DP systems.

An Assessment of Turbulence Models for Predicting the Fluid Flow in Spiral Casing of a Hydraulic Turbomachine Using SUPG-Finite Element Method

2013 ◽  
Author(s):  
N. Parameswara Rao ◽  
K. Arul Prakash
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Spatial Discretisation ◽  
High Reynolds ◽  
Spiral Casing ◽  
Element Method

Numerical simulation of complex three-dimensional flow through the spiral casing has been studied using a finite element method. An explicit Eulerian velocity correction scheme has been employed to solve the Reynolds averaged Navier-stokes equations. The simulation has been performed to describe the flow in high Reynolds number (106) regime and two k-ε turbulence models (standard k-ε and RNG k-ε) have been used for computing the turbulent flow. A streamline upwind Petrov Galerkin technique has been used for spatial discretisation. The velocity field and the pressure distribution inside the spiral casing has been studied. It has been observed that very strong secondary flow is evolved on the cross-stream planes.

scholarly journals Feasible Concept of an Air-Driven Fan with a Tip Turbine for a High-Bypass Propulsion System

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3350 ◽  
Author(s):  
Guoping Huang ◽  
Xin Xiang ◽  
Chen Xia ◽  
Weiyu Lu ◽  
Lei Li
Keyword(s):  
Fluid Dynamics ◽  
Carbon Dioxide Emissions ◽  
Three Dimensional ◽  
Propulsion System ◽  
Navier Stokes ◽  
Three Dimensional Flow ◽  
Low Pressure Turbine ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method ◽  
Bypass Ratio

The reduction in specific fuel consumption (SFC) is crucial for small/mid-size cost-controllable aircraft, which is very conducive to reducing cost and carbon dioxide emissions. To decrease the SFC, increasing the bypass ratio (BPR) is an important way. Conventional high-BPR engines have several limitations, especially the conflicting spool-speed requirements of a fan and a low-pressure turbine. This research proposes an air-driven fan with a tip turbine (ADFTT) as a potential device for a high-bypass propulsion system. Moreover, a possible application of this ADFTT is introduced. Thermodynamic analysis results show that an ADFTT can improve thrust from a prototype turbofan. As a demonstration, we selected a typical small-thrust turbofan as the prototype and applied the ADFTT concept to improve this model. Three-dimensional flow fields were numerically simulated through a Reynolds averaged Navier-Stokes (RANS)-based computational fluid dynamics (CFD) method. The performance of this ADFTT has the possibility of amplifying the BPR more than four times and increasing the thrust by approximately 84% in comparison with the prototype turbofan.

scholarly journals ICCM2015: A Comparison of RANS and LES Computational Methods in Analyzing Ventilation Flow Through a Room Fitted with a Two-Sided Windcatcher

2017 ◽  
Vol 14 (03) ◽  
pp. 1750021 ◽  
Author(s):  
A. Niktash ◽  
B. P. Huynh
Keyword(s):  
Natural Ventilation ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Interior Space ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Through ◽  
Cfd Method ◽  
Good Agreement

A windcatcher is a structure for providing natural ventilation using wind power; it is usually fitted on the roof of a building to exhaust the inside stale air to the outside and supplies the outside fresh air into the building interior space working by pressure difference between outside and inside of the building. In this paper, the behavior of free wind flow through a three-dimensional room fitted with a centered position two-canal bottom shape windcatcher model is investigated numerically, using a commercial computational fluid dynamics (CFD) software package and LES (Large Eddy Simulation) CFD method. The results have been compared with the obtained results for the same model but using RANS (Reynolds Averaged Navier–Stokes) CFD method. The model with its surrounded space has been considered in both method. It is found that the achieved results for the model from LES method are in good agreement with RANS method’s results for the same model.

A Low-Order Model for Predicting Turbocharger Turbine Unsteady Performance

2016 ◽  
Vol 138 (7) ◽  
Author(s):  
Teng Cao ◽  
Liping Xu
Keyword(s):  
Power Output ◽  
Three Dimensional ◽  
Pulsating Flow ◽  
Navier Stokes ◽  
Order Model ◽  
Wave Dynamics ◽  
Predicting Performance ◽  
Set Up ◽  
Cfd Method ◽  
Low Order

In this paper, a low-order model for predicting performance of radial turbocharger turbines is presented. The model combines an unsteady quasi-three-dimensional (Q3D) computational fluid dynamics (CFD) method with multiple one-dimensional (1D) meanline impeller solvers. The new model preserves the critical volute geometry features, which is crucial for the accurate prediction of the wave dynamics and retains effects of the rotor inlet circumferential nonuniformity. It also still maintains the desirable properties of being easy to set-up and fast to run. The model has been validated against a experimentally validated full 3D unsteady Reynolds-averaged Navier–Stokes (URANS) solver. The loss model in the meanline model is calibrated by the full 3D RANS solver under the steady flow states. The unsteady turbine performance under different inlet pulsating flow conditions predicted by the model was compared with the results of the full 3D URANS solver. Good agreement between the two was obtained with a speed-up ratio of about 4 orders of magnitude (∼104) for the low-order model. The low-order model was then used to investigate the effect of different pulse wave amplitudes and frequencies on the turbine cycle averaged performance. For the cases tested, it was found that compared with quasi-steady performance, the unsteady effect of the pulsating flow has a relatively small impact on the cycle-averaged turbine power output and the cycle-averaged mass flow capacity, while it has a large influence on the cycle-averaged ideal power output and cycle-averaged efficiency. This is related to the wave dynamics inside the volute, and the detailed mechanisms responsible are discussed in this paper.

scholarly journals Comparative Study on CFD Turbulence Models for the Flow Field in Air Cooled Radiator

Processes ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 1687
Author(s):  
Chao Yu ◽  
Xiangyao Xue ◽  
Kui Shi ◽  
Mingzhen Shao ◽  
Yang Liu
Keyword(s):  
Flow Field ◽  
Transient Flow ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Compartment Model ◽  
Navier Stokes ◽  
Engine Compartment ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Relevant Calculation

This paper compares the performances of three Computational Fluid Dynamics (CFD) turbulence models, Reynolds Average Navier-Stokes (RANS), Detached Eddy Simulation (DES), and Large Eddy Simulation (LES), for simulating the flow field of a wheel loader engine compartment. The distributions of pressure fields, velocity fields, and vortex structures in a hybrid-grided engine compartment model are analyzed. The result reveals that the LES and DES can capture the detachment and breakage of the trailing edge more abundantly and meticulously than RANS. Additionally, by comparing the relevant calculation time, the feasibility of the DES model is proved to simulate the three-dimensional unsteady flow of engine compartment efficiently and accurately. This paper aims to provide a guiding idea for simulating the transient flow field in the engine compartment, which could serve as a theoretical basis for optimizing and improving the layout of the components of the engine compartment.

Effect of Blade Numbers on Pressure Drop of Axial Cyclone Separators by CFD

2011 ◽  
Vol 55-57 ◽  
pp. 343-347 ◽  
Author(s):  
Yi Gang Luan ◽  
Hai Ou Sun
Keyword(s):  
Pressure Drop ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Three Dimensional Model ◽  
Navier Stokes Equations ◽  
Pressure Drops ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method ◽  
Resistance Performance

In this article, computational fluid dynamics(CFD) method is used to predict the effect of blade numbers on the pressure drop of axial cyclone separators. A three-dimensional model is built to acquire the resistance of axial cyclone separators with different blade numbers. The flow field inside cyclone separators is calculated using 3D Reynolds-averaged Navier-Stokes equations. And turbulence model is used to simulate the Reynold stress. Also pressure drop of cyclone separators with different blade numbers is expressed as a function of different inlet velocities. At the same inlet velocity with increasing the blade numbers, pressure drops of cyclones reduce greatly. And changing the blade number of cyclone separator is an effective method to improve its resistance performance.

Sign in / Sign up

Export Citation Format

Share Document