Comparison of Tacking and Wearing Performance Between a Japanese Traditional Square Rig and a Chinese Lug Rig

2005 ◽  
Author(s):  
Yutaka Masuyama ◽  
Akira Sakurai ◽  
Toichi Fukas ◽  
Kazunori Aoki
Keyword(s):  
Wind Tunnel ◽  
Vortex Lattice ◽  
Aerodynamic Performance ◽  
Measured Data ◽  
The Other ◽  
Aerodynamic Forces ◽  
Lattice Method ◽  
Wind Tunnel Tests ◽  
Vortex Lattice Method ◽  
Force Variation

Aerodynamic performance of a Japanese traditional square rig, “Bezai-ho”, and a Chinese lug rig, “Shinshi-bo” in Japanese, were studied by means of wind tunnel tests, sea trials and numerical calculations. Sail forces and sail shapes were measured in the wind tunnel tests. A sail dynamometer boat Fujin was employed for the sea trials, by which aerodynamic forces acting on sail, sail shapes, and sailing conditions of the boat can be measured at the same time. Using the measured sail shapes, sail forces are calculated by means of a vortex lattice method. Differences of sail performance of the above mentioned two types of rig were clarified in the wind tunnel tests and sea trials. The calculated sail performance shows good agreements with the measured data in upwind condition. Dynamic sail performance of the two types of rig during tacking and wearing operations was also clarified in the sea trials using the boat Fujin. Details of sail force variation in time during maneuvering can be investigated by the sail dynamometer system. For the “Bezai-ho,” the backward force acting on sail when the boat changes tacks (wind over the bow) was investigated. At this moment, the square sail falls into a “caught aback” situation, which makes the tacking operation difficult. On the other hand, “Shinshi-bo” showed good steady performance similar to that of the modern marconi rig, and good tacking performance. Obtained results of steady and dynamic sail performance in this paper provide useful information for sail trimming and maneuvering of boats equipped with the western square rigs and modern lug rig introduced by H.G. Hasler.

Propeller aerodynamic performance by vortex-lattice method

1985 ◽  
Vol 22 (8) ◽  
pp. 649-654 ◽  
Author(s):  
Makoto Kobayakawa ◽  
Hiroyuki Onuma
Keyword(s):  
Vortex Lattice ◽  
Aerodynamic Performance ◽  
Lattice Method ◽  
Vortex Lattice Method

Modified Unsteady Vortex Lattice Method for Aerodynamics of Flapping Wing Models

2015 ◽  
Author(s):  
Anh Tuan Nguyen ◽  
Jae-Hung Han
Keyword(s):  
Vortex Lattice ◽  
Micro Air Vehicles ◽  
Flapping Wing ◽  
Preliminary Design ◽  
Aerodynamic Forces ◽  
Lattice Method ◽  
Real Motion ◽  
Flapping Motion ◽  
The Real ◽  
Vortex Lattice Method

Motivated by extensive possible applications of flapping-wing micro-air vehicles (MAVs) to various different areas, there has been an increasing amount of research related to this issue. In the stage of preliminary studies, one of the most important tasks is to predict the aerodynamic forces generated by the flapping motion. Studying aerodynamics of insects is an efficient way to approach the preliminary design of flapping-wing MAVs. In this paper, a modified version of an Unsteady Vortex Lattice Method (UVLM) is developed to compute aerodynamic forces appearing in flapping-wing models. A hawkmoth-like wing with kinematics based on the real motion is used for the simulations in this paper.

Calculation of the Aerodynamic Forces on Automotive Lifting Surfaces

1985 ◽  
Vol 107 (4) ◽  
pp. 438-443 ◽  
Author(s):  
J. Katz
Keyword(s):  
Steady State ◽  
Vortex Lattice ◽  
Numerical Technique ◽  
Angle Of Attack ◽  
Ground Effect ◽  
Aerodynamic Forces ◽  
Lattice Method ◽  
Vortex Lattice Method ◽  
Close Proximity ◽  
Lifting Surfaces

A numerical technique was developed to investigate the performance of automotive lifting surfaces in close proximity to ground. The model is based on the Vortex Lattice Method and includes freely-deforming wake elements. The ground effect was simulated by reflection and both steady and unsteady pressures and loads on various wing planforms were considered. Calculated results are presented for wings having both positive and negative incidences, with and without ground effect. Also the transient lift of a wing in a plunging motion was analyzed in ground proximity and at a negative angle of attack. Finally the periodic lift fluctuations on the front winglet of a racing car, due to its suspension oscillations, were calculated and found to exceed approximately twice the steady-state value.

scholarly journals Nonlinear Aeroelastic Simulations and Stability Analysis of the Pazy Wing Aeroelastic Benchmark

Aerospace ◽  
2021 ◽  
Vol 8 (10) ◽  
pp. 308
Author(s):  
Jonathan Hilger ◽  
Markus Raimund Ritter
Keyword(s):  
Stability Analysis ◽  
Wind Tunnel ◽  
Vortex Lattice ◽  
Structural Model ◽  
State Space Model ◽  
Lattice Method ◽  
Vortex Lattice Method ◽  
Aeroelastic Simulations ◽  
The Stability ◽  
German Aerospace

The Pazy wing aeroelastic benchmark is a highly flexible wind tunnel model investigated in the Large Deflection Working Group as part of the Third Aeroelastic Prediction Workshop. Due to the design of the model, very large elastic deformations in the order of 50% span are generated at highest dynamic pressures and angles of attack in the wind tunnel. This paper presents static coupling simulations and stability analyses for selected onflow velocities and angles of attack. Therefore, an aeroelastic solver developed at the German Aerospace Center (DLR) is used for static coupling simulations, which couples a vortex lattice method with the commercial finite element solver MSC Nastran. For the stability analysis, a linearised aerodynamic model is derived analytically from the unsteady vortex lattice method and integrated with a modal structural model into a monolithic aeroelastic discrete-time state-space model. The aeroelastic stability is then determined by calculating the eigenvalues of the system’s dynamics matrix. It is shown that the stability of the wing in terms of flutter changes significantly with increasing deflection and is heavily influenced by the change in modal properties, i.e., structural eigenvalues and eigenvectors.

Generalized vortex lattice method for planar supersonic flow

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 1230-1233
Author(s):  
Paulo A. O. Soviero ◽  
Hugo B. Resende
Keyword(s):  
Supersonic Flow ◽  
Vortex Lattice ◽  
Lattice Method ◽  
Vortex Lattice Method

scholarly journals Static Aeroelastic Characteristics of Morphing Trailing-Edge Wing Using Geometrically Exact Vortex Lattice Method

2019 ◽  
Vol 2019 ◽  
pp. 1-15
Author(s):  
Sen Mao ◽  
Changchuan Xie ◽  
Lan Yang ◽  
Chao Yang
Keyword(s):  
Vortex Lattice ◽  
Deflection Angle ◽  
Aircraft Design ◽  
Analysis Method ◽  
Lattice Method ◽  
Trailing Edge ◽  
Vortex Lattice Method ◽  
Analysis And Design ◽  
Aeroelastic Analysis ◽  
Typical Model

A morphing trailing-edge (TE) wing is an important morphing mode in aircraft design. In order to explore the static aeroelastic characteristics of a morphing TE wing, an efficient and feasible method for static aeroelastic analysis has been developed in this paper. A geometrically exact vortex lattice method (VLM) is applied to calculate the aerodynamic forces. Firstly, a typical model of a morphing TE wing is chosen and built which has an active morphing trailing edge driven by a piezoelectric patch. Then, the paper carries out the static aeroelastic analysis of the morphing TE wing and corresponding simulations were carried out. Finally, the analysis results are compared with those of a traditional wing with a rigid trailing edge using the traditional linearized VLM. The results indicate that the geometrically exact VLM can better describe the aerodynamic nonlinearity of a morphing TE wing in consideration of geometrical deformation in aeroelastic analysis. Moreover, out of consideration of the angle of attack, the deflection angle of the trailing edge, among others, the wing system does not show divergence but bifurcation. Consequently, the aeroelastic analysis method proposed in this paper is more applicable to the analysis and design of a morphing TE wing.

Sign in / Sign up

Export Citation Format

Share Document