scholarly journals Resistance Welding of Aluminium Alloys with an Electromechanical Electrode Force System

2020 ◽  
Author(s):  
Zygmunt Mikno
Keyword(s):  
Aluminium Alloys ◽  
Weld Zone ◽  
Welding Process ◽  
Weld Nugget ◽  
Energy Concentration ◽  
Force System ◽  
Welding Machine ◽  
Electrode Force ◽  
Force Systems ◽  
Calculation Results

The idea presented in this chapter is an innovative welding machine electrode force system. The operation, advantages of the new solution and the optimisation of the welding process were illustrated by the welding of aluminium bars (5182) (ø 4 mm). The solution involves controlling the force and/or displacement of welding machine electrodes. The modulation of electrode force significantly improves welding, particularly as regards aluminium alloys (requiring a very short welding process). The tests involved the numerical analysis of two electrode force systems, i.e. a conventional Pneumatic Force System (PFS) and an Electromechanical (Servomechanical Force) System (EFS). The numerical tests were performed using SORPAS software. FEM calculation results were verified experimentally. The technological welding tests were conducted using inverter welding machines (1 kHz) equipped with various electrode force systems. The research included metallographic and strength (peeling) tests and measurements of characteristic parameters. The welding process optimisation based on the EFS and the hybrid algorithm of force control resulted in i) more favourable space distribution of welding power, ii) energy concentration in the central weld zone, iii) favourable melting of the material within the entire weld transcrystallisation zone, iv) obtainment of the full weld nugget and v) longer weld nugget diameter.

scholarly journals Cross-Wire Projection Welding of Aluminium Alloys in Relation to Pneumatic and Electromechanical Electrode Force Systems

2018 ◽  
Vol 1 (4) ◽  
Author(s):  
Z. Mikno
Keyword(s):  
Hybrid Algorithm ◽  
Welding Process ◽  
Space Distribution ◽  
Energy Concentration ◽  
Welding Parameters ◽  
Force System ◽  
Projection Welding ◽  
Electrode Force ◽  
Force Systems ◽  
Cross Wire

The cross wire projection welding of wires (Al 5182, =4 mm) performed using the conventional (i.e. pneumatic) electrode force system was subjected to thorough numerical analysis. Calculations were performed until one of adopted boundary conditions, i.e. maximum welding time, maximum penetration of wires, the occurrence of expulsion or the exceeding of the temperature limit in the contact between the electrode and the welded material was obtained. It was observed that the ring weld was formed within the entire range of welding parameters. The process of welding was subjected to optimisation through the application of a new electromechanical electrode force system and the use of a special hybrid algorithm of electrode force and/or displacement control. Comparative numerical calculations were performed (using SORPAS software) for both electrode force systems. Technological welding tests were performed using inverter welding machines (1 kHz) provided with various electrode force systems. The research also involved the performance of metallographic and strength (peeling) tests as well as measurements of welding process characteristic parameters (welding current and voltage).The welding process optimisation involving the use of the electromechanical force system and the application of the hybrid algorithm of force control resulted in i) more favourable space distribution of welding power, ii) energy concentration in the central zone of the weld, iii) favourable (desired) melting of the material within the entire weld transcrystallisation zone and iv) obtainment of a full weld nugget.

Effects of bottom plate in friction stir welding of AA6061-T6

2020 ◽  
Vol 118 (1) ◽  
pp. 108
Author(s):  
M.A. Vinayagamoorthi ◽  
M. Prince ◽  
S. Balasubramanian
Keyword(s):  
Mechanical Properties ◽  
Axial Load ◽  
Weld Zone ◽  
Welding Process ◽  
Bottom Plate ◽  
Welding Parameters ◽  
Nugget Zone ◽  
Friction Stir ◽  
Weld Joints ◽  
Fine Grain

The effects of 40 mm width bottom plates on the microstructural modifications and the mechanical properties of a 6 mm thick FSW AA6061-T6 joint have been investigated. The bottom plates are placed partially at the weld zone to absorb and dissipate heat during the welding process. An axial load of 5 to 7 kN, a rotational speed of 500 rpm, and a welding speed of 50 mm/min are employed as welding parameters. The size of the nugget zone (NZ) and heat-affected zone (HAZ) in the weld joints obtained from AISI 1040 steel bottom plate is more significant than that of weld joints obtained using copper bottom plate due to lower thermal conductivity of steel. Also, the weld joints obtained using copper bottom plate have fine grain microstructure due to the dynamic recrystallization. The friction stir welded joints obtained with copper bottom plate have exhibited higher ductility of 8.9% and higher tensile strength of 172 MPa as compared to the joints obtained using a steel bottom plate.

Welding Procedure Establishment for Tubular Joints Welded by Single Station, Solid State Welding Machine

2010 ◽  
Author(s):  
Ganesan S. Marimuthu ◽  
Per Thomas Moe ◽  
Bjarne Salberg ◽  
Junyan Liu ◽  
Henry Valberg ◽  
...  
Keyword(s):  
Solid State ◽  
Oil And Gas ◽  
Welding Process ◽  
High Strength ◽  
Pipe Material ◽  
Tubular Joints ◽  
Welding Machine ◽  
Single Station ◽  
Welding Procedure ◽  
Treatment Procedures

Forge welding is an efficient welding method for tubular joints applicable in oil and gas industries due to its simplicity in carrying out the welding, absence of molten metal and filler metals, small heat-affected zone and high process flexibility. Prior to forging, the ends (bevels) of the joining tubes can be heated by torch or electromagnetic (EM) techniques, such as induction or high frequency resistance heating. The hot bevels are subsequently pressed together to establish the weld. The entire welding process can be completed within seconds and consistently produces superior quality joints of very high strength and adequate ductility. Industrial forge welding of tubes in the field is relatively expensive compared to laboratory testing. Moreover, at the initial stages of a new project sufficient quantities of pipe material may not be available for weldability testing. For these and several other reasons we have developed a highly efficient single station, solid state welding machine that carefully replicates the thermomechanical conditions of full-scale Shielded Active Gas Forge Welding Machines (SAG-FWM) for pipeline and casing applications. This representative laboratory machine can be used to weld tubular goods, perform material characterization and/or simulate welding and heat treatment procedures. The bevel shapes at mating ends of the tubes are optimized by ABAQUS® simulations to fine tune temperature distribution. The main aim of this paper is to establish a welding procedure for welding the tubular joints by the representative laboratory machine. The quality of the welded tubular joint was analyzed by macro/micro analyses, as well as hardness and bend tests. The challenges in optimizing the bevel shape and process parameters to weld high quality tubular joints are thoroughly discussed. Finally a welding procedure specification was established to weld the tubular joints in the representative laboratory machine.

Investigation of the Cleaning and Welding Steps From the Friction Element Welding Process

2017 ◽  
Author(s):  
Jamie D. Skovron ◽  
Brandt J. Ruszkiewicz ◽  
Laine Mears ◽  
Tim Abke ◽  
Ankit Varma ◽  
...  
Keyword(s):  
Weld Zone ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Process Time ◽  
Friction Element ◽  
Joint Quality ◽  
Head Height ◽  
Friction Element Welding ◽  
Step Parameters

The requirement of increased fuel economy standards has forced automakers to incorporate multi-materials into their current steel dominant vehicles in order to lightweight their fleets. Technologies such as Self Piercing Rivets and Flow Drill Screws are currently implemented for joining aluminum to high-strength steels but only one-technology is viable for joining aluminum to ultra-high-strength steels without pre-holes, namely Friction Element Welding. This study is aimed at investigating how variations in the cleaning and welding steps of the Friction Element Welding process influence joint quality. A design of experiment was conducted to understand the influence of key process parameters (endload, spindle RPM, and relative distance) during these steps on the pre-defined joint quality metrics of head height, weld zone diameter, under-head fill area, temperature, and microhardness. It is found that cleaning step parameters have the greatest influence on process time and energy consumption, while welding step parameters greatly influence maximum torque on the element, head height, and underhead fill, with both cleaning force and weld force influencing weld diameter, all parameters influence temperature.

scholarly journals The Effect of Copper and Brass on Friction Stir Welded Dissimilar Aluminium Alloy When Used as in Thin Sheet Form

2016 ◽  
Vol 45 (2) ◽  
pp. 118-122
Author(s):  
G. Gopala Krishna ◽  
P.Ram Reddy ◽  
M.Manzoor Hussain
Keyword(s):  
Aluminium Alloy ◽  
Aluminium Alloys ◽  
Low Cost ◽  
Thin Sheet ◽  
Welding Process ◽  
Cost Effective ◽  
Tensile Tests ◽  
Fusion Welding ◽  
Friction Stir ◽  
Effect Of Copper

In recent year’s aluminium and aluminium alloys are most widely used in many applications because of light weight, good formability and malleability, corrosion resistance, moderate strength and low cost. Friction Stir Welding (FSW) process is efficient and cost effective method for welding aluminium and aluminium alloys. FSW is a solid state welding process that means the material is not melted during the process. Complete welding process accomplishes below the melting point of materials so it overcomes many welding defects that usually happens with conventional fusion welding technique which were initially used for low melting materials. Though this process is initially developed for low melting materials but now process is widely used for a variety of other materials including titanium, steel and also for composites. The present butt jointed FSW experimental work has been done in two ways. Initially a comparison of tensile properties of friction stir (FS) welded similar aluminium alloy (AA6351 with AA6351) and dissimilar aluminium alloy (AA6351 with AA5083) combinations. Later the effect of impurities (copper and brass) in sheet form (0.1 mm thick) when used as insert in between two dissimilar aluminium alloy (AA6351 with AA5083) plates during FSW. Tensile tests were performed for these combinations and results were compared for with and without using strip material (copper and brass).

Study on Electron Beam Welding of AZ61 Magnesium Alloy

2010 ◽  
Vol 34-35 ◽  
pp. 1516-1520
Author(s):  
Hong Ye ◽  
Han Li Yang ◽  
Zhong Lin Yan
Keyword(s):  
Electron Beam ◽  
Magnesium Alloys ◽  
Welding Speed ◽  
Electron Beam Welding ◽  
Weld Zone ◽  
Welding Process ◽  
Processing Parameters ◽  
Beam Current ◽  
Fine Grained ◽  
Section Shape

Electron beam welding process of AZ61 with 10mm thickness magnesium alloys was investigated. The influence of processing parameters including focusing current, welding beam current and welding speed was researched. The results show that an ideal weld bead can be formed by choosing processing parameters properly. Focusing current is main parameter that determines cross section shape. The beam current and welding speed are main parameters that determine the weld width and dimensions. The test results for typical welds indicate that the microhardness of the weld zone is better than that of the base meta1. A fine-grained weld region has been observed and no obvious heat-affected zone is found. The fusion zone mainly consists of small α-Mg phase and β-Mg17A112. The small grains and β phases in the joint are believed to play an important role in the increase of the strength of weld for AZ61 magnesium alloys.

Demonstration of Intelligent Welding Machine for Polyethylene Pipe

2021 ◽  
Author(s):  
Guangte Xiang ◽  
Yurui Hu ◽  
Sheng Zeng ◽  
Jianfeng Shi ◽  
Jinyang Zheng
Keyword(s):  
Welding Process ◽  
Maximum Temperature ◽  
Welding Parameters ◽  
Welding Time ◽  
Constant Voltage ◽  
Welding Machine ◽  
Reinforced Composite ◽  
Composite Pipe ◽  
The Difference

Abstract Electrofusion (EF) welding is one of the most common connection methods for polyethylene (PE) pipe, as well as thermoplastic pipe and reinforced composite pipe. Conventional EF welding generally adopts constant-voltage welding mode. The welding machine outputs a constant welding voltage to heat the resistance wire within specific welding time. In our previous study, intelligent welding machine was designed to ensure the quality of the EF joint, based on the study of the temperature field in EF joint. In this paper, three experiments were used to show the difference between the intelligent welding machine and traditional welding machine. The intelligent welding machine can actively adjust the welding parameters to ensure the quality of EF joint even it was given the wrong welding voltage and welding time. Compared with the traditional welding machine, the intelligent welding machine can automatically control the maximum temperature and the depth of melting region in EF joint during the welding process, and this method applies for EF joints with various diameters or design welding parameters.

Sign in / Sign up

Export Citation Format

Share Document