scholarly journals MEMS-Based Micro-heat Pipes

10.5772/62786 ◽  
2016 ◽  
Author(s):  
Qu Jian ◽  
Wang Qian
Keyword(s):  
Heat Pipes ◽  
Micro Heat Pipes

The Heat Transport Capacity of Micro Heat Pipes

1998 ◽  
Vol 120 (4) ◽  
pp. 1064-1071 ◽  
Author(s):  
J. M. Ha ◽  
G. P. Peterson
Keyword(s):  
Experimental Data ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Pipes ◽  
Original Model ◽  
Semiempirical Model ◽  
Transport Capacity ◽  
Predictive Tool ◽  
Maximum Heat ◽  
Micro Heat Pipes

The original analytical model for predicting the maximum heat transport capacity in micro heat pipes, as developed by Cotter, has been re-evaluated in light of the currently available experimental data. As is the case for most models, the original model assumed a fixed evaporator region and while it yields trends that are consistent with the experimental results, it significantly overpredicts the maximum heat transport capacity. In an effort to provide a more accurate predictive tool, a semi-empirical correlation has been developed. This modified model incorporates the effects of the temporal intrusion of the evaporating region into the adiabatic section of the heat pipe, which occurs as the heat pipe approaches dryout conditions. In so doing, the current model provides a more realistic picture of the actual physical situation. In addition to incorporating these effects, Cotter’s original expression for the liquid flow shape factor has been modified. These modifications are then incorporated into the original model and the results compared with the available experimental data. The results of this comparison indicate that the new semiempirical model significantly improves the correlation between the experimental and predicted results and more accurately represents the actual physical behavior of these devices.

Evaporation and Viscous Flow in Triangular Grooves in Micro Heat Pipes

2005 ◽  
Author(s):  
Mulugeta Markos ◽  
Vladimir S. Ajaev ◽  
G. M. Homsy
Keyword(s):  
Cross Section ◽  
Flow Rate ◽  
Cross Sections ◽  
Wedge Angle ◽  
Heat Pipes ◽  
Type Model ◽  
Pressure Gradients ◽  
Maximum Value ◽  
Dry Out ◽  
Micro Heat Pipes

We develop a lubrication type model of a liquid flow in a wedge in the limit of small capillary numbers and negligible gravity. The model incorporates the effects of capillary pressure gradients and evaporation. Steady vapor-liquid interface shapes are found for a range of parameters. In the limit of weak evaporation the flow is the same in all cross-sections and can be controlled by changing the wedge angle. We find the wedge angle that results in the maximum value of the flow rate for a given contact angle. For high evaporation rates, both the flow rate and the amount of liquid in each cross-section along the wedge decrease until the point of dry-out is reached. The location of the dry-out point is studied as a function of evaporation. Practical suggestions about optimization of micro heat pipes are given.

Steady-State Investigation of Vapor Deposited Micro Heat Pipe Arrays

1995 ◽  
Vol 117 (1) ◽  
pp. 75-81 ◽  
Author(s):  
A. K. Mallik ◽  
G. P. Peterson
Keyword(s):  
Thermal Conductivity ◽  
Steady State ◽  
Surface Temperature ◽  
Heat Pipe ◽  
Effective Thermal Conductivity ◽  
Heat Pipes ◽  
Temperature Gradients ◽  
Bottom Surface ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

An experimental investigation of vapor deposited micro heat pipe arrays was conducted using arrays of 34 and 66 micro heat pipes occupying 0.75 and 1.45 percent of the cross-sectional area, respectively. The performance of wafers containing the arrays was compared with that of a plain silicon wafer. All of the wafers had 8 × 8 mm thermofoil heaters located on the bottom surface to simulate the active devices in an actual application. The temperature distributions across the wafers were obtained using a Hughes Probeye TVS Infrared Thermal Imaging System and a standard VHS video recorder. For wafers containing arrays of 34 vapor deposited micro heat pipes, the steady-state experimental data indicated a reduction in the maximum surface temperature and temperature gradients of 24.4 and 27.4 percent, respectively, coupled with an improvement in the effective thermal conductivity of 41.7 percent. For wafers containing arrays of 66 vapor deposited micro heat pipes, the corresponding reductions in the surface temperature and temperature gradients were 29.0 and 41.7 percent, respectively, and the effective thermal conductivity increased 47.1 percent, for input heat fluxes of 4.70 W/cm2. The experimental results were compared with the results of a previously developed numerical model, which was shown to predict the temperature distribution with a high degree of accuracy, for wafers both with and without the heat pipe arrays.

scholarly journals An investigation on effect of EDL on heat transfer of micro heat pipe with square and triangular cross section

2020 ◽  
Vol 21 (3) ◽  
pp. 309
Author(s):  
Maryam Fallah Abbasi ◽  
Hossein Shokouhmand ◽  
Morteza Khayat
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Double Layer ◽  
Electric Double Layer ◽  
Heat Pipes ◽  
The Body ◽  
Working Fluid ◽  
Two Phase ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

Electronic industries have always been trying to improve the efficiency of electronic devices with small dimensions through thermal management of this equipment, thus increasing the use of small thermal sinks. In this study micro heat pipes with triangular and square cross sections have been manufactured and tested. One of the main objectives is to obtain an understanding of micro heat pipes and their role in energy transmission with electrical double layer (EDL). Micro heat pipes are highly efficient heat transfer devices, which use the continuous evaporation/condensation of a suitable working fluid for two-phase heat transport in a closed system. Since the latent heat of vaporization is very large, heat pipes transport heat at small temperature difference, with high rates. Because of variety of advantage features these devices have found a number of applications both in space and terrestrial technologies. The theory of operation micro heat pipes with EDL is described and the micro heat pipe has been studied. The temperature distribution have achieved through five thermocouples installed on the body. Water and different solution mixture of water and ethanol have used to investigate effect of the electric double layer heat transfer. It was noticed that the electric double layer of ionized fluid has caused reduction of heat transfer.

Fabrication and test of radial grooved micro heat pipes

2002 ◽  
Vol 22 (14) ◽  
pp. 1559-1568 ◽  
Author(s):  
Shung-Wen Kang ◽  
Sheng-Hong Tsai ◽  
Hong-Chih Chen
Keyword(s):  
Heat Pipes ◽  
Micro Heat Pipes

Experimental Investigation of the Maximum Heat Transport in Triangular Grooves

1996 ◽  
Vol 118 (3) ◽  
pp. 740-746 ◽  
Author(s):  
H. B. Ma ◽  
G. P. Peterson
Keyword(s):  
Experimental Investigation ◽  
Heat Transport ◽  
Heat Pipes ◽  
Effective Area ◽  
Experimental Results ◽  
Test Facility ◽  
Working Fluid ◽  
Maximum Heat ◽  
Pressure Losses ◽  
Micro Heat Pipes

An experimental investigation was conducted and a test facility constructed to measure the capillary heat transport limit in small triangular grooves, similar to those used in micro heat pipes. Using methanol as the working fluid, the maximum heat transport and unit effective area heat transport were experimentally determined for ten grooved plates with varying groove widths, but identical apex angles. The experimental results indicate that there exists an optimum groove configuration, which maximizes the capillary pumping capacity while minimizing the combined effects of the capillary pumping pressure and the liquid viscous pressure losses. When compared with a previously developed analytical model, the experimental results indicate that the model can be used accurately to predict the heat transport capacity and maximum unit area heat transport when given the physical characteristics of the working fluid and the groove geometry, provided the proper heat flux distribution is known. The results of this investigation will assist in the development of micro heat pipes capable of operating at increased power levels with greater reliability.

Sign in / Sign up

Export Citation Format

Share Document