scholarly journals Elastic and Nanowearing Properties of SiO2-PMMA and Hybrid Coatings Evaluated by Atomic Force Acoustic Microscopy and Nanoindentation"

10.5772/36219 ◽  
2012 ◽  
Author(s):  
J. Alvarado-Rivera ◽  
J. Muoz-Saldaa ◽  
R. Ramrez-Bo
Keyword(s):  
Acoustic Microscopy ◽  
Hybrid Coatings ◽  
Atomic Force

Atomic force acoustic microscopy characterization of carbon-based materials

2007 ◽  
Author(s):  
D. Passeri ◽  
A. Bettucci ◽  
M. Germano ◽  
A. Biagioni ◽  
M. Rossi ◽  
...  
Keyword(s):  
Acoustic Microscopy ◽  
Atomic Force ◽  
Microscopy Characterization ◽  
Carbon Based

scholarly journals Measurement of the Indentation Modulus and the Local Internal Friction in Amorphous SiO2 Using Atomic Force Acoustic Microscopy

2016 ◽  
Vol 61 (1) ◽  
pp. 9-12
Author(s):  
B. Zhang ◽  
H. Wagner ◽  
M. Büchsenschütz-Göbeler ◽  
Y. Luo ◽  
S. Küchemann ◽  
...  
Keyword(s):  
Internal Friction ◽  
Amorphous Materials ◽  
Contact Stiffness ◽  
Ultrasonic Transducer ◽  
Amorphous Material ◽  
Acoustic Microscopy ◽  
Damping Factor ◽  
Indentation Modulus ◽  
Amorphous Sio2 ◽  
Atomic Force

Abstract For the past two decades, atomic force acoustic microscopy (AFAM), an advanced scanning probe microscopy technique, has played a promising role in materials characterization with a good lateral resolution at micro/nano dimensions. AFAM is based on inducing out-of-plane vibrations in the specimen, which are generated by an ultrasonic transducer. The vibrations are sensed by the AFM cantilever when its tip is in contact with the material under test. From the cantilver’s contactresonance spectra, one determines the real and the imaginary part of the contact stiffness k*, and then from these two quantities the local indentation modulus M' and the local damping factor Qloc-1 can be obtained with a spatial resolution of less than 10 nm. Here, we present measured data of M' and of Qloc-1 for the insulating amorphous material, a-SiO2. The amorphous SiO2 layer was prepared on a crystalline Si wafer by means of thermal oxidation. There is a spatial distribution of the indentation modulus M' and of the internal friction Qloc-1. This is a consequence of the potential energy landscape for amorphous materials.

Infrared Characterization of PMMA-SiO2 Hybrid Glasses Obtained by Sol-Gel Process

2010 ◽  
Vol 1278 ◽  
Author(s):  
L.L. Díaz-Flores ◽  
A. S. López Rodríguez ◽  
P. SifuentesGallardo ◽  
M.A. Hernàndez Rivera ◽  
M.a Garnica Romo ◽  
...  
Keyword(s):  
Sol Gel ◽  
Chemical Properties ◽  
Hybrid Coatings ◽  
Force Microscopy ◽  
Air Atmosphere ◽  
Atomic Force ◽  
Sol Gel Process ◽  
Traditional Process ◽  
And Chemical Properties

AbstractThis work is about the production of hybrid coatings of the system SiO2-PMMA (PMMA, polymethylmethacrylate). These materials have interesting mechanical and chemical properties useful for anticorrosive and wear resistance applications. SiO2-PMMA hybrids were obtained by the sol-gel traditional process, using tetraethylorthosilicate (TEOS) and methylmethacrylate (MMA) by Aldrich Co, as starting reagents. The SiO2:PMMA ratio was varied from 0:1 to about 1:1 at air atmosphere deposition. The coatings were obtained on acrylic sheets and silicon wafers. A diversity of coatings with chemical composition ranging from SiO2 and PMMA to obtain the SiO2-PMMA hybrids were obtained. Infrared (IR) and atomic force microscopy (AFM), were performed to determinate structural and morphological behavior.

Mechanical characterization of nanoporous materials by use of atomic force acoustic microscopy methods

2013 ◽  
Vol 24 (35) ◽  
pp. 355703 ◽  
Author(s):  
M Kopycinska-Müller ◽  
K-B Yeap ◽  
S Mahajan ◽  
B Köhler ◽  
N Kuzeyeva ◽  
...  
Keyword(s):  
Mechanical Characterization ◽  
Nanoporous Materials ◽  
Acoustic Microscopy ◽  
Atomic Force

Quantitative Contact Spectroscopy by Atomic-Force Acoustic Microscopy

2006 ◽  
pp. 179-186
Author(s):  
U. Rabe ◽  
E. Kester ◽  
V. Scherer ◽  
W. Arnold
Keyword(s):  
Acoustic Microscopy ◽  
Atomic Force

scholarly journals Atomic force acoustic microscopy reveals the influence of substrate stiffness and topography on cell behavior

2019 ◽  
Vol 10 ◽  
pp. 2329-2337 ◽  
Author(s):  
Yan Liu ◽  
Li Li ◽  
Xing Chen ◽  
Ying Wang ◽  
Meng-Nan Liu ◽  
...  
Keyword(s):  
Acoustic Microscopy ◽  
Substrate Stiffness ◽  
Cell Behavior ◽  
Cell Alignment ◽  
Nondestructive Technique ◽  
Elastic Deformations ◽  
L929 Cells ◽  
Atomic Force ◽  
Cell Substrate ◽  
Influence Of Substrate

The stiffness and the topography of the substrate at the cell–substrate interface are two key properties influencing cell behavior. In this paper, atomic force acoustic microscopy (AFAM) is used to investigate the influence of substrate stiffness and substrate topography on the responses of L929 fibroblasts. This combined nondestructive technique is able to characterize materials at high lateral resolution. To produce substrates of tunable stiffness and topography, we imprint nanostripe patterns on undeveloped and developed SU-8 photoresist films using electron-beam lithography (EBL). Elastic deformations of the substrate surfaces and the cells are revealed by AFAM. Our results show that AFAM is capable of imaging surface elastic deformations. By immunofluorescence experiments, we find that the L929 cells significantly elongate on the patterned stiffness substrate, whereas the elasticity of the pattern has only little effect on the spreading of the L929 cells. The influence of the topography pattern on the cell alignment and morphology is even more pronounced leading to an arrangement of the cells along the nanostripe pattern. Our method is useful for the quantitative characterization of cell–substrate interactions and provides guidance for the tissue regeneration therapy in biomedicine.

Sign in / Sign up

Export Citation Format

Share Document