scholarly journals Modeling Moisture Movement in Rice

10.5772/15317 ◽  
2011 ◽  
Author(s):  
Bhagwati Prakash ◽  
Zhongli P
Keyword(s):  
Moisture Movement

Modelling of Moisture Movement in Wood during Outdoor Storage

2001 ◽  
Vol 6 (2) ◽  
pp. 3-14 ◽  
Author(s):  
R. Baronas ◽  
F. Ivanauskas ◽  
I. Juodeikienė ◽  
A. Kajalavičius
Keyword(s):  
Experimental Data ◽  
Finite Difference ◽  
Climatic Conditions ◽  
Two Dimensional ◽  
Moisture Movement ◽  
Finite Difference Technique ◽  
Long Term Storage ◽  
Space Formulation ◽  
Term Storage

A model of moisture movement in wood is presented in this paper in a two-dimensional-in-space formulation. The finite-difference technique has been used in order to obtain the solution of the problem. The model was applied to predict the moisture content in sawn boards from pine during long term storage under outdoor climatic conditions. The satisfactory agreement between the numerical solution and experimental data was obtained.

Influence of Sulphate on the Moisture Movement of Calcium Silicate Brick Masonry Wall

2010 ◽  
Vol 133-134 ◽  
pp. 201-204
Author(s):  
Ibrahim Mohamad H. Wan ◽  
B.H. Abu Bakar ◽  
M.A. Megat Johari ◽  
P.J. Ramadhansyah
Keyword(s):  
Relative Humidity ◽  
Calcium Silicate ◽  
Masonry Wall ◽  
Sodium Sulphate ◽  
Brick Masonry ◽  
Masonry Walls ◽  
Moisture Movement ◽  
Moisture Expansion ◽  
Curing Period ◽  
Wet Condition

This paper presents the behaviour of moisture movement of calcium silicate brick masonry walls exposed to sodium sulphate environment. The walls were exposed to three sodium sulphate conditions with sulphate concentrations of5%, 10% and 15%. For comparison, some walls were also exposed to dry and wet condition which acts as a control conditions. All specimens were prepared and cured under polythene sheet for 14 days in a controlled environmental room and maintained at relative humidity and temperature of 80 ± 5% and 25 ± 2°C, respectively. After the curing period, the specimens were exposed to sodium sulphate as well as drying and water exposures, during which moisture movement was measured and monitored for a period of up to 7 months. As a result, the moisture expansion was observed and recorded for all masonry wall specimens after exposed to the sulphate condition.

Modelling of the Development of the Vertical Density Profile of MDF during Hot Pressing

2007 ◽  
Vol 2 (2) ◽  
Author(s):  
Arun Gupta ◽  
Patrick Jordan ◽  
Shusheng Pang
Keyword(s):  
Moisture Content ◽  
Density Profile ◽  
Hot Pressing ◽  
Major Influence ◽  
Transfer Model ◽  
Uniform Density ◽  
Moisture Movement ◽  
Vertical Density Profile ◽  
Vertical Density ◽  
Pressing Operation

The hot pressing operation is one of the most important operations in medium density fibreboard (MDF) manufacture. Complicated dynamic interactions occur during pressing, including heat transfer, moisture movement, development of gas pressure, internal stress development and relaxation, wood consolidation, resin curing, bonding between particles and eventual development of a non-uniform density distribution through the panel thickness. Consequently the mat experiences continuously changing internal conditions (temperature and moisture content) as the pressing operation proceeds. The vertical density profile (VDP) has a major influence on the MDF strength and physical properties. This influence of the VDP on the board properties is generally recognised, but the formation of the density profile and their specific effects on the board performance have proved difficult to quantify. A mathematical model based on theoretical analysis and experimental information is being developed. In the model, the mat is divided into a number of thin parallel layers. The deformation of each layer is a function of stress, temperature and moisture content of the layer. The model incorporates the variation of the mat mechanical and rheological properties with moisture content and temperature. The changes in temperature and moisture content are provided by a separate heat and mass transfer model. The present model can predict stress, strain, layer deformation and density across the thickness during pressing. The performance of the model was validated by experiments conducted in a pilot-scale press. Twelve MDF boards were made with different pressing parameters, and the VDP were measured and compared with the simulation results from the model. The model could predict the density profile with an acceptable accuracy for the main variables that control the manufacturing of MDF boards.

Sign in / Sign up

Export Citation Format

Share Document