scholarly journals The Investigation of Laser Lap Welding Process on High-Strength Galvanized Steel Sheets

2011 ◽  
Vol 2011 ◽  
pp. 1-7 ◽  
Author(s):  
Shiquan Zhou ◽  
Yi Zhao ◽  
Zhenguo Peng ◽  
Fangjie Ren
Keyword(s):  
Laser Welding ◽  
Welding Process ◽  
High Strength ◽  
Galvanized Steel ◽  
Process Technology ◽  
Surface Appearance ◽  
Beam Laser ◽  
Dual Beam ◽  
Laser Lap Welding ◽  
Lap Welding

The development of automobile steel was analyzed in this paper; it is pointed out that high-strength galvanized steel will be widely used in the car body structure. By analyzing welding problems about the dual phase (DP) series of high-strength galvanized steel, the importance of laser welding was concerned. Finally, laser lap welding process technology of high-strength galvanized steel was studied; the results show that the lap weld with welding process smooth and spatter-free as well as beautiful welding bead surface appearance and good mechanical properties can be made by using the dual-beam laser welding technology and interlayer for welding high-strength galvanized steel.

Investigation of Fluid Flow and Heat Transfer in 3D Dual-Beam Laser Keyhole Welding

2010 ◽  
Author(s):  
Jun Zhou ◽  
Hai-Lung Tsai
Keyword(s):  
Heat Transfer ◽  
Laser Welding ◽  
Welding Process ◽  
Solidification Process ◽  
Melt Flow ◽  
Single Beam ◽  
Keyhole Welding ◽  
Beam Laser ◽  
Dual Beam ◽  
Laser Keyhole Welding

Dual-beam laser welding has become an emerging joining technique. Studies have demonstrated that it can provide benefits over conventional single-beam laser welding, such as increasing keyhole stability, slowing down cooling rate and delaying the humping onset to a higher welding speed. It is also reported to be able to improve weld quality significantly. However, due to its complexity the development of this promising technique has been limited to the trial-and-error procedure. In this study, mathematical models are developed to investigate the heat transfer, melt flow, and solidification process in three-dimensional dual-beam laser keyhole welding. Effects of key parameters, such as laser-beam configuration on melt flow, weld shape, and keyhole dynamics are studied. Some experimentally observed phenomena, such as the changes of the weld pool shape from oval to circle and from circle to oval during the welding process are analyzed in current study.

Study on Quality Control of the Laser Welding Joint

2013 ◽  
Vol 442 ◽  
pp. 276-281
Author(s):  
Qiang Wu ◽  
Lan Ying Xu
Keyword(s):  
Laser Welding ◽  
Salt Water ◽  
Harmful Effect ◽  
Welding Process ◽  
High Strength ◽  
Galvanized Steel ◽  
Welding Parameters ◽  
Test Results ◽  
Welding Joint ◽  
Corrosion Rates

During laser welding process of high-strength galvanized steel, adopting guiding arc plate and the connecting arc plate can avoid harmful effect resulted in unstable melting width. The galvanized layer protecting joint is inevitably lost by having been burned, which affects stain resistance of welding joint. So salt water with the concentration of 3% is used in the corrosion test for the samples welded under different laser parameters, mass variation and metallographic microscopes are gained after joint being corroded. The test results indicate that the corrosion rates of the joint are different under different welding parameters during laser welding of high-strength galvanized steel; their average corrosion rates are coincident with that of base metal and laser welding technology hardly effect corrosion resistance of the joint.

Fluid Flow and Weld Pool Dynamics in Dual-Beam Laser Keyhole Welding

2003 ◽  
Author(s):  
J. Hu ◽  
H. L. Tsai
Keyword(s):  
Fluid Flow ◽  
Laser Welding ◽  
Weld Pool ◽  
Welding Process ◽  
Laser Beams ◽  
Pool Shape ◽  
Beam Laser ◽  
Dual Beam ◽  
Oval Shape ◽  
Weld Pool Shape

The use of dual or multiple laser beams is necessary for welding thick-section metals, especially for Nd:Yag lasers which are limited to relatively low power as compared to CO2 lasers. It was also reported that the use of dual laser beams for welding can increase keyhole stability leading to a better weld quality. So far, the development of dual-beam laser welding technologies has been in the experimental stage. The objective of this paper is to develop mathematical models and the associated numerical techniques to calculate the transient heat transfer and fluid flow in the weld pool and to study weld pool dynamics during the dual-beam laser welding process. The simulation was conducted for a three-dimensional stationary dual-beam laser welding. A very interesting change of the top-surface view of the weld pool was predicted. During the welding process, the top-view shape of the weld pool changes, starting from an oval-shape with the long-axis connecting the centers of the two laser beams, to a circle, and finally to an oval-shape with the short-axis connecting the centers of the two laser beams. Although a direct comparison with published experimental observation is impossible (due to the lack of detailed experimental data), the predicted weld pool shape is similar to that observed from experiments. The dynamical change of the weld pool shape can be well explained by the predicted fluid flow field.

scholarly journals Porosity Characteristics and Effect on Tensile Shear Strength of High-Strength Galvanized Steel Sheets after the Gas Metal Arc Welding Process

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1077 ◽  
Author(s):  
Seungmin Shin ◽  
Sehun Rhee
Keyword(s):  
Shear Strength ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
High Strength ◽  
Galvanized Steel ◽  
Tensile Shear Strength ◽  
Tensile Shear ◽  
Tensile Test Specimen ◽  
Metal Arc Welding

In this study, lap joint experiments were conducted using galvanized high-strength steel, SGAFH 590 FB 2.3 mmt, which was applied to automotive chassis components in the gas metal arc welding (GMAW) process. Zinc residues were confirmed using a semi-quantitative energy dispersive X-ray spectroscopy (EDS) analysis of the porosity in the weld. In addition, a tensile shear test was performed to evaluate the weldability. Furthermore, the effect of porosity defects, such as blowholes and pits generated in the weld, on the tensile shear strength was experimentally verified by comparing the porosity at the weld section of the tensile test specimen with that measured through radiographic testing.

Noise Reduction During Acoustic Monitoring of Laser Welding of High-Strength Steels

2009 ◽  
Author(s):  
Wei Huang ◽  
Radovan Kovacevic
Keyword(s):  
Laser Welding ◽  
Noise Reduction ◽  
Acoustic Signal ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Weld Penetration ◽  
Acoustic Signatures ◽  
Reduction Methods ◽  
Laser Welding Process

During the laser welding process of high-strength steels, different defects, such as a partial weld penetration, spatters, and blow-through holes could be present. In order to detect the presence of defects and achieve a quality control, acoustic monitoring based on microphones is applied to the welding process. As an effective sensor to monitor the laser welding process, however, the microphone is greatly limited by intensive noise existing in the complex industrial environment. In this paper, in order to acquire a clean acoustic signal from the laser welding process, two noise reduction methods are proposed: one is the spectral subtraction method based on one microphone and the other one is the beamforming based on a microphone array. By applying these two noise reduction methods, the quality of the acoustic signal is enhanced, and the acoustic signatures are extracted both in the time domain and frequency domain. The analysis results show that the extracted acoustic signatures can well indicate the different weld penetration states and they can also be used to study the internal mechanisms of the laser-material interaction.

Sign in / Sign up

Export Citation Format

Share Document