Branched Chain Natural Rubber Derivatives Obtained by Reaction with Azodicarboxylates

1957 ◽  
Vol 30 (3) ◽  
pp. 895-902
Author(s):  
S. S. Ivanov ◽  
N. A. Yuzefovich ◽  
A. V. Sidorovich ◽  
E. F. Fedorova
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Natural Rubber ◽  
Side Chains ◽  
Damping Decrement ◽  
Branched Chain

Abstract 1. Ethyl azodicarboxylate (EAD) and ethylene dis-ethyl azodicarboxylate (DEAD) react quantitatively with natural rubber to form branched and cross-linked derivatives, respectively. 2. The mechanical properties of vulcanizates from natural rubber containing side branches (obtained with the aid of EAD) differ greatly from the properties of unbranched vulcanizates. 3. Analysis of the load-extension diagrams shows that the introduction of EAD side chains into natural rubber results in the formation of vulcanizates with high extensions at low loads. Vulcanizates without EAD have steeper load-extension diagrams and lower extensions at break. 4. As the temperature rises from 20 to 100°, the elastic modulus and mechanical losses (or the logarithmic damping decrement) of vulcanizates cross-linked with DEAD decreases greatly (about 4–7 times). Addition of 10 per cent (g-equiv.) of EAD side chains approximately doubles the mechanical losses in comparison with vulcanizates without EAD.

scholarly journals Tuning of the elastic modulus of a soft polythiophene through molecular doping

2021 ◽  
Author(s):  
Sepideh Zokaei ◽  
Donghyun Kim ◽  
Emmy Järsvall ◽  
Abigail M. Fenton ◽  
Albree R. Weisen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Side Chains ◽  
Molecular Doping ◽  
Oligoethylene Glycol

Molecular doping of a polythiophene with oligoethylene glycol side chains is found to strongly modulate not only the electrical but also the mechanical properties of the polymer.

scholarly journals Macromolecular Structure Controlling Micro Mechanical Properties of Vitrinite and Inertinite in Tectonically Deformed Coals—A Case Study in Fengfeng Coal Mine of Taihangshan Fault Zone (North China)

Energies ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 6618
Author(s):  
Anmin Wang ◽  
Daiyong Cao ◽  
Yingchun Wei ◽  
Zhifei Liu
Keyword(s):  
Mechanical Properties ◽  
Dipole Moment ◽  
Elastic Modulus ◽  
Intermolecular Forces ◽  
Molecular Structures ◽  
Macromolecular Structure ◽  
Side Chains ◽  
13C Nuclear Magnetic Resonance ◽  
Benzene Rings ◽  
Nanoindentation Experiment

In order to study the evolution of the mechanical properties and macromolecular structures in different macerals of tectonically deformed coal (TDC), vitrinite and inertinite samples were handpicked from six block TDCs in the same coal seam with an increasing deformation degree (unaltered, cataclastic, porphyroclast, scaly and powdery coal). The micro mechanical properties were tested by the nanoindentation experiment and the macromolecular structures were measured using 13C nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR). The results show that the range of hardness and elastic modulus of inertinite is 0.373–1.517 GPa and 4.339–12.158 GPa, respectively, which is significantly higher than that of vitrinite with values of 0.278–0.456 GPa and 4.857–7.810 GPa, respectively. From unaltered coal to powdery coal, the hardness of vitrinite and inertinite gradually decreases, with the difference between these macerals becomes smaller and the elastic modulus of vitrinite shows an increasing trend, while that of inertinite was more variable. Both the NMR and FITR results reveal that the macromolecular structure of inertinite has similar structural transitions as vitrinite. As the degree of deformation increases, the aliphatic side chains become shorter and the aromaticity is increasing. Macromolecular alterations caused by tectonic stress is expected to produce defects in the TDCs, therefore there should be more interspacing among the macromolecular groups for the extrusion of macromolecules caused by the indenter of the nanoindentation experiment, thereby reducing the hardness. The elastic modulus of coal is believed to be related to intermolecular forces, which are positively correlated to the dipole moment. By calculating the dipole moments of the typical aromatic molecular structures with aliphatic side chains, the detachment of the aliphatic side chains and the growth of benzene rings can both increase the dipole moment, which can promote elastic modulus. In addition, the increasing number of benzene rings can create more π-π bonds between the molecules, which can lead to an increase in the intermolecular forces, further increasing the elastic modulus.

EFFECT OF ZINC DITHIOCARBAMATES AND THIAZOLE-BASED ACCELERATORS ON THE VULCANIZATION OF NATURAL RUBBER

2012 ◽  
Vol 85 (1) ◽  
pp. 120-131 ◽  
Author(s):  
Md. Najib Alam ◽  
Swapan Kumar Mandal ◽  
Subhas Chandra Debnath
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Performance Liquid Chromatography ◽  
Liquid Chromatography ◽  
Reaction Mechanism ◽  
Natural Rubber ◽  
High Performance ◽  
Binary Systems ◽  
Synergistic Activity ◽  
Tetramethylthiuram Disulfide

Abstract Several zinc dithiocarbamates (ZDCs) as accelerator derived from safe amine has been exclusively studied in the presence of thiazole-based accelerators to introduce safe dithiocarbamate in the vulcanization of natural rubber. Comparison has been made between conventional unsafe zinc dimethyldithiocarbamate (ZDMC) with safe novel ZDC combined with thizole-based accelerators in the light of mechanical properties. The study reveals that thiuram disulfide and 2-mercaptobenzothiazole (MBT) are always formed from the reaction either between ZDC and dibenzothiazyledisulfide (MBTS) or between ZDC and N-cyclohexyl-2-benzothiazole sulfenamide (CBS). It has been conclusively proved that MBT generated from MBTS or CBS reacts with ZDC and produces tetramethylthiuram disulfide. The observed synergistic activity has been discussed based on the cure and physical data and explained through the results based on high-performance liquid chromatography and a reaction mechanism. Synergistic activity is observed in all binary systems studied. The highest tensile strength is observed in the zinc (N-benzyl piperazino) dithiocarbamate-accelerated system at 3:6 mM ratios. In respect of tensile strength and modulus value, unsafe ZDMC can be successfully replaced by safe ZDCs in combination with thiazole group containing accelerator.

scholarly journals Experimental Analysis of the Mechanical Properties and Resistivity of Tectonic Coal Samples with Different Particle Sizes

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2303
Author(s):  
Congyu Zhong ◽  
Liwen Cao ◽  
Jishi Geng ◽  
Zhihao Jiang ◽  
Shuai Zhang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Coalbed Methane ◽  
Coal Sample ◽  
Fine Particles ◽  
Particle Sizes ◽  
Tectonic Coal

Because of its weak cementation and abundant pores and cracks, it is difficult to obtain suitable samples of tectonic coal to test its mechanical properties. Therefore, the research and development of coalbed methane drilling and mining technology are restricted. In this study, tectonic coal samples are remodeled with different particle sizes to test the mechanical parameters and loading resistivity. The research results show that the particle size and gradation of tectonic coal significantly impact its uniaxial compressive strength and elastic modulus and affect changes in resistivity. As the converted particle size increases, the uniaxial compressive strength and elastic modulus decrease first and then tend to remain unchanged. The strength of the single-particle gradation coal sample decreases from 0.867 to 0.433 MPa and the elastic modulus decreases from 59.28 to 41.63 MPa with increasing particle size. The change in resistivity of the coal sample increases with increasing particle size, and the degree of resistivity variation decreases during the coal sample failure stage. In composite-particle gradation, the proportion of fine particles in the tectonic coal sample increases from 33% to 80%. Its strength and elastic modulus increase from 0.996 to 1.31 MPa and 83.96 to 125.4 MPa, respectively, and the resistivity change degree decreases. The proportion of medium particles or coarse particles increases, and the sample strength, elastic modulus, and resistivity changes all decrease.

scholarly journals Rheometer Evidences for the Co-Curing Effect of a Bismaleimide in Conjunction with the Accelerated Sulfur on Natural Rubber/Chloroprene Rubber Blends

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1510
Author(s):  
Marek Pöschl ◽  
Shibulal Gopi Sathi ◽  
Radek Stoček ◽  
Ondřej Kratina
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Crosslinking Agent ◽  
Alder Reaction ◽  
Diels Alder ◽  
Ene Reactions ◽  
Rubber Blends ◽  
Diels Alder Reaction ◽  
Chloroprene Rubber

The rheometer curing curves of neat natural rubber (NR) and neat chloroprene rubber (CR) with maleide F (MF) exhibit considerable crosslinking torque at 180 °C. This indicates that MF can crosslink both these rubbers via Alder-ene reactions. Based on this knowledge, MF has been introduced as a co-crosslinking agent for a 50/50 blend of NR and CR in conjunction with accelerated sulfur. The delta (Δ) torque obtained from the curing curves of a blend with the addition of 1 phr MF was around 62% higher than those without MF. As the content of MF increased to 3 phr, the Δ torque was further raised to 236%. Moreover, the mechanical properties, particularly the tensile strength of the blend with the addition of 1 phr MF in conjunction with the accelerated sulfur, was around 201% higher than the blend without MF. The overall tensile properties of the blends cured with MF were almost retained even after ageing the samples at 70 °C for 72 h. This significant improvement in the curing torque and the tensile properties of the blends indicates that MF can co-crosslink between NR and CR via the Diels–Alder reaction.

scholarly journals Experimental and Numerical Analysis of the Mechanical Properties of a Pretreated Shape Memory Alloy Wire in a Self-Centering Steel Brace

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 80
Author(s):  
Bo Zhang ◽  
Sizhi Zeng ◽  
Fenghua Tang ◽  
Shujun Hu ◽  
Qiang Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Energy Dissipation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Loading Rate ◽  
Effective Elastic Modulus ◽  
Maximum Energy ◽  
Numerical Results ◽  
Energy Dissipation Capacity

As a stimulus-sensitive material, the difference in composition, fabrication process, and influencing factors will have a great effect on the mechanical properties of a superelastic Ni-Ti shape memory alloy (SMA) wire, so the seismic performance of the self-centering steel brace with SMA wires may not be accurately obtained. In this paper, the cyclic tensile tests of a kind of SMA wire with a 1 mm diameter and special element composition were tested under multi-working conditions, which were pretreated by first tensioning to the 0.06 strain amplitude for 40 cycles, so the mechanical properties of the pretreated SMA wires can be simulated in detail. The accuracy of the numerical results with the improved model of Graesser’s theory was verified by a comparison to the experimental results. The experimental results show that the number of cycles has no significant effect on the mechanical properties of SMA wires after a certain number of cyclic tensile training. With the loading rate increasing, the pinch effect of the hysteresis curves will be enlarged, while the effective elastic modulus and slope of the transformation stresses in the process of loading and unloading are also increased, and the maximum energy dissipation capacity of the SMA wires appears at a loading rate of 0.675 mm/s. Moreover, with the initial strain increasing, the slope of the transformation stresses in the process of loading is increased, while the effective elastic modulus and slope of the transformation stresses in the process of unloading are decreased, and the maximum energy dissipation capacity appears at the initial strain of 0.0075. In addition, a good agreement between the test and numerical results is obtained by comparing with the hysteresis curves and energy dissipation values, so the numerical model is useful to predict the stress–strain relations at different stages. The test and numerical results will also provide a basis for the design of corresponding self-centering steel dampers.

Sign in / Sign up

Export Citation Format

Share Document