scholarly journals Study on the synthesis of heterostructure MoS2/TiO2 material for photocatalytic degradation of 2,4-dichlorophenoxyacetic acid

2021 ◽  
Vol 10 (3) ◽  
pp. xx-xx
Author(s):  
Tuan Dao Thi ◽  
Lan Phung Thi ◽  
Mo Nguyen Thi ◽  
Ha Nguyen Ngoc ◽  
Ha Nguyen Thi Thu ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Degradation Rate ◽  
Hydrothermal Reaction ◽  
Absorption Capacity ◽  
Argon Atmosphere ◽  
Dichlorophenoxyacetic Acid ◽  
Electron Hole ◽  
Reaction Method ◽  
2,4 Dichlorophenoxyacetic Acid

Nanoflower MoS2, nanowire TiO2(NNW) and 3D MoS2/TiO2 nano-heterostructure have been synthesized successfully by simple typical hydrothermal reaction method followed by 200oC calcination under an argon atmosphere. The prepared samples are characterized in detail by XRD, FESEM, UV-vis DRS, EDX and BET. The results suggest that the TiO2 NNWis successfully coupled with MoS2 to form the heterojunction nanostructure. The hybrid heterostructures can effectively utilize visible-light and solar energy to degrade 2,4-dichlorophenoxyacetic acid (2,4-D). The degradation rate of 2,4-D is as high as 99%. The improved photocatalytic activity owes to the decreased band-gap and the heterosurface properties of MoS2/TiO2, promoting the electron-hole pairs separation and absorption capacity to visible light. This work presents a facile approach for fabricating the MoS2/TiO2 heterostructures for efficient photocatalytic 2,4-D solution, which will facilitate the development of designing photo catalysts applied in environment and energy.

scholarly journals High photocatalytic activity of Fe2O3/TiO2 nanocomposites prepared by photodeposition for degradation of 2,4-dichlorophenoxyacetic acid

2017 ◽  
Vol 8 ◽  
pp. 915-926 ◽  
Author(s):  
Shu Chin Lee ◽  
Hendrik O Lintang ◽  
Leny Yuliati
Keyword(s):  
Photocatalytic Activity ◽  
Uv Light ◽  
Active Species ◽  
High Photocatalytic Activity ◽  
Dichlorophenoxyacetic Acid ◽  
Electron Hole ◽  
And Performance ◽  
2,4 Dichlorophenoxyacetic Acid ◽  
Hole Recombination

Two series of Fe2O3/TiO2 samples were prepared via impregnation and photodeposition methods. The effect of preparation method on the properties and performance of Fe2O3/TiO2 for photocatalytic degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) under UV light irradiation was examined. The Fe2O3/TiO2 nanocomposites prepared by impregnation showed lower activity than the unmodified TiO2, mainly due to lower specific surface area caused by heat treatment. On the other hand, the Fe2O3/TiO2 nanocomposites prepared by photodeposition showed higher photocatalytic activity than the unmodified TiO2. Three times higher photocatalytic activity was obtained on the best photocatalyst, Fe2O3(0.5)/TiO2. The improved activity of TiO2 after photodeposition of Fe2O3 was contributed to the formation of a heterojunction between the Fe2O3 and TiO2 nanoparticles that improved charge transfer and suppressed electron–hole recombination. A further investigation on the role of the active species on Fe2O3/TiO2 confirmed that the crucial active species were both holes and superoxide radicals. The Fe2O3(0.5)/TiO2 sample also showed good stability and reusability, suggesting its potential for water purification applications.

scholarly journals Enhanced Visible-Light Photocatalytic Performance of SAPO-5-Based g-C3N4 Composite for Rhodamine B (RhB) Degradation

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3948
Author(s):  
Lingfang Qiu ◽  
Zhiwei Zhou ◽  
Mengfan Ma ◽  
Ping Li ◽  
Jinyong Lu ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Redox Reactions ◽  
Photocatalytic Performance ◽  
Dye Degradation ◽  
Thermal Polymerization ◽  
Light Illumination ◽  
Electron Hole ◽  
Visible Light Illumination ◽  
Visible Light Photocatalytic

Novel visible-light responded aluminosilicophosphate-5 (SAPO-5)/g-C3N4 composite has been easily constructed by thermal polymerization for the mixture of SAPO-5, NH4Cl, and dicyandiamide. The photocatalytic activity of SAPO-5/g-C3N4 is evaluated by degrading RhB (30 mg/L) under visible light illumination (λ > 420 nm). The effects of SAPO-5 incorporation proportion and initial RhB concentration on the photocatalytic performance have been discussed in detail. The optimized SAPO-5/g-C3N4 composite shows promising degradation efficiency which is 40.6% higher than that of pure g-C3N4. The degradation rate improves from 0.007 min−1 to 0.022 min−1, which is a comparable photocatalytic performance compared with other g-C3N4-based heterojunctions for dye degradation. The migration of photo-induced electrons from g-C3N4 to the Al site of SAPO-5 should promote the photo-induced electron-hole pairs separation rate of g-C3N4 efficiently. Furthermore, the redox reactions for RhB degradation occur on the photo-induced holes in the g-C3N4 and Al sites in SAPO-5, respectively. This achievement not only improves the photocatalytic activity of g-C3N4 efficiently, but also broadens the application of SAPOs in the photocatalytic field.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Enhanced visible-active photocatalytic behaviors observed in Mn-doped BiFeO3

2018 ◽  
Vol 32 (17) ◽  
pp. 1850185 ◽  
Author(s):  
Yun-Hui Si ◽  
Yu Xia ◽  
Ya-Yun Li ◽  
Shao-Ke Shang ◽  
Xin-Bo Xiong ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Band Gap ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
X Ray ◽  
Mn Doped ◽  
Hole Recombination ◽  
Narrow Band Gap Semiconductors

A series of BiFeO3 and BiFe[Formula: see text]Mn[Formula: see text]O3 (x = 0, 0.02, 0.04, 0.06, 0.08, 0.10) were synthesized by a hydrothermal method. The samples were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy (EDS) and UV–Vis diffuse reflectance spectroscopy, and their photocatalytic activity was studied by photocatalytic degradation of methylene blue in aqueous solution under visible light irradiation. The band gap of BiFeO3 was significantly decreased from 2.26 eV to 1.90 eV with the doping of Mn. Furthermore, the 6% Mn-doped BiFeO3 photocatalyst exhibited the best activity with a degradation rate of 94% after irradiation for 100 min. The enhanced photocatalytic activity with Mn doping could be attributed to the enhanced optical absorption, increment of surface reactive sites and reduction of electron–hole recombination. Our results may be conducive to design more efficient photocatalysts responsive to visible light among narrow band gap semiconductors.

W-Doped TiO2 Preparation and Photocatalytic Degradation of Guaiacol

2014 ◽  
Vol 513-517 ◽  
pp. 33-36 ◽  
Author(s):  
Zi Chang Xie ◽  
Ying Wang ◽  
Peng Wang ◽  
Lei Zhang
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Degradation Rate ◽  
Amorphous State ◽  
X Ray Diffraction ◽  
Model Compounds ◽  
Plant Fibers ◽  
X Ray ◽  
Crystallite Structure

In this paper, W-doped TiO2 (W-TiO2) powder was prepared in hydrothermal method by mixing TiO2 and ammonium metatungstate. The catalysts were characterized by X-ray diffraction and ultraviolet spectrophotometer. The results displayed that W-TiO2 showed an anatase crystallite structure with 2 % W content. W-element in W-TiO2 was amorphous state. The guaiacol was degraded with the W-TiO2 in the visible light. It was a model compounds of lignin existed in the plant fibers. The degradation rate of guaiacol was increased with the photocatalytic time, as high as 88.21 % after 360 min irradiation. It was concluded that the W-TiO2 had an obvious photocatalytic activity under visible light. It can be used in the photocatalytic degradation of lignin.

scholarly journals Comparative Study of Four TiO2-Based Photocatalysts to Degrade 2,4-D in a Semi-Passive System

Water ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 621 ◽  
Author(s):  
Gisoo Heydari ◽  
Jordan Hollman ◽  
Gopal Achari ◽  
Cooper Langford
Keyword(s):  
Energy Consumption ◽  
Degradation Rate ◽  
Light Emitting Diode ◽  
Three Dimensional ◽  
Dichlorophenoxyacetic Acid ◽  
Light Emitting ◽  
Glass Spheres ◽  
Degradation Rate Constant ◽  
2,4 Dichlorophenoxyacetic Acid ◽  
Mode Energy

In this study, the relative efficiency of four forms of supported titanium dioxide (TiO2) as a photocatalyst to degrade 2,4-dichlorophenoxyacetic acid (2,4-D) in Killex®, a commercially available herbicide was studied. Coated glass spheres, anodized plate, anodized mesh, and electro-photocatalysis using the anodized mesh were evaluated under an ultraviolet – light-emitting diode (UV-LED) light source at λ = 365 nm in a semi-passive mode. Energy consumption of the system was used to compare the efficiency of the photocatalysts. The results showed both photospheres and mesh consumed approximately 80 J/cm3 energy followed by electro-photocatalysis (112.2 J/cm3), and the anodized plate (114.5 J/cm3). Although electro-photocatalysis showed the fastest degradation rate (K = 5.04 mg L−1 h−1), its energy consumption was at the same level as the anodized plate with a lower degradation rate constant of 3.07 mg L−1 h−1. The results demonstrated that three-dimensional nanotubes of TiO2 surrounding the mesh provide superior degradation compared to one-dimensional arrays on the planar surface of the anodized plate. With limited broad-scale comparative studies between varieties of different TiO2 supports, this study provides a comparative analysis of relative degradation efficiencies between the four photocatalytic configurations.

Photocatalytic activity of ZrO2 composites with graphitic carbon nitride for hydrogen production under visible light

2019 ◽  
Vol 43 (11) ◽  
pp. 4455-4462 ◽  
Author(s):  
Mohammed Ismael ◽  
Ying Wu ◽  
Michael Wark
Keyword(s):  
Photocatalytic Activity ◽  
Hydrogen Production ◽  
Visible Light ◽  
Water Splitting ◽  
Carbon Nitride ◽  
Graphitic Carbon Nitride ◽  
Superior Performance ◽  
Electron Hole ◽  
Effective Electron ◽  
Composite Interface

The synthesized ZrO2/g-C3N4 composites exhibit superior performance in water splitting for hydrogen production due to the effective electron–hole separation at the composite interface.

Sign in / Sign up

Export Citation Format

Share Document