x-The Effect of Microstructure on the Corrosion Fatigue Property of A7N01P-T4 Aluminum Alloy Welding Joints

CORROSION ◽  
10.5006/2805 ◽  
2018 ◽  
Vol 74 (11) ◽  
pp. 1229-1236
Author(s):  
Feng Xiao ◽  
Jiangli An ◽  
Hui Chen ◽  
P. Li ◽  
Wei Gao
Keyword(s):  
Grain Boundaries ◽  
Corrosion Fatigue ◽  
Fatigue Property ◽  
Short Crack ◽  
Al Alloy ◽  
Second Phase ◽  
Test Results ◽  
Second Phase Particles ◽  
The Matrix ◽  
Almost All

The corrosion fatigue short crack propagation (CFSCP) behavior of A7N01P-T4 Al alloy welded joints in 3.5 wt% NaCl solution has been investigated. The test results indicate that the CFSCP followed a cyclical type of growth. Microscopic study shows that almost all second-phase particles are distributed along the grain boundary areas. These particles were easily dissolved during the corrosion fatigue test, resulting in weak grain boundaries. Therefore, the fatigue short crack will grow along the winding grain boundaries. While the second-phase particles on the grain boundaries were the main factor to cause the intergranular crack. Transgranular cracking may occur to the coarse grains in the matrix, which indicate that grain size also has a strong influence on the CFSCP behavior of A7N01P-T4 Al alloy.

Influence of Ni5Zr Particles on Fatigue Property of Ni3Al Alloy

1994 ◽  
Vol 364 ◽  
Author(s):  
Gang Li ◽  
Jian-Ting Guo ◽  
Zhong-Guang Wang
Keyword(s):  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Fatigue Crack Initiation ◽  
Fatigue Property ◽  
Fatigue Tests ◽  
Al Alloy ◽  
Second Phase ◽  
Cycle Fatigue ◽  
Second Phase Particles ◽  
Minimum Stress

AbstractIn this investigation, the influence of second phase particles on high cycle fatigue behavior of Ni3Al alloy is studied. A single phase Ni3Al-B alloy and a Ni3Al-B/Zr alloy with a few second phase particles (Ni5Zr) at the grain boundaries are selected for investigation. High cycle fatigue tests at room temperature with R (minimum stress/maximum stress) 0.1 are conducted in air and at 30 Hz. The results show that the second phase particles are detrimental to high cycle fatigue resistance. It may be explained in terms of the second phase particles promoting fatigue crack initiation. The characteristics of fracture surfaces are examined by Scanning Electron Microscopy (SEM).

Continuous and Discontinuous Recrystallization of 6013 Aluminum Alloy

2013 ◽  
Vol 753 ◽  
pp. 221-224 ◽  
Author(s):  
Krzysztof Sztwiertnia ◽  
Magdalena Bieda ◽  
Anna Korneva
Keyword(s):  
Aluminum Alloy ◽  
Grain Boundaries ◽  
Second Phase ◽  
Sheet Plane ◽  
Temperature Range ◽  
Orientation Mapping ◽  
Second Phase Particles ◽  
The Matrix ◽  
Continuous Recrystallization

In situ orientation mapping using TEM and calorimetric measurements were carried out to investigate the annealing behavior of cold-rolled 6013 aluminum alloy. The recrystallization of the material can be considered to be a number of processes that correspond to two separate stored energy release peaks. In the temperature range of the peak 1, the deformation zones around the large second-phase particles acted as sites for particle-stimulated nucleation. In the matrix, at the same time, some elongation of grains occurred. The elongated matrix grains appeared because of the reduction of the dislocation density and the annihilation of some low-angle grain boundaries between chains of subgrains lying in layers parallel to the sheet plane. The matrix processes in this temperatures range can be considered forms of continuous recrystallization. The matrix high-angle grain boundaries started to migrate at the temperature range of the peak 2. They moved mostly in the direction normal to the sheet plane. Heating of the sample for an appropriate time at those temperatures resulted in the complete discontinuous recrystallization of the material. The recrystallized microstructure was dominated now by elongated grains, which were a few times thicker than those obtained by annealing at the temperatures of the peak 1.

Composites Fabrication via Friction Stir Processing

2011 ◽  
Vol 690 ◽  
pp. 125-128 ◽  
Author(s):  
Ning Sun ◽  
Diran Apelian
Keyword(s):  
Friction Stir Processing ◽  
Al Alloy ◽  
Second Phase ◽  
Alloy Matrix ◽  
Friction Stir ◽  
Surface Composites ◽  
Second Phase Particles ◽  
The Matrix ◽  
High Level ◽  
Advanced Tool

Friction stir processing (FSP) is a post-processing method that locally manipulates the microstructure by imparting a high level of energy in the solid state giving rise to improved mechanical properties. Additionally, FSP has emerged as an advanced tool to produce surface composites and synthesize the second phase into the matrix. In the current study, FSP was investigated for the manufacture of localized zones of composite materials made by the emplacement of a second phase into cast A206 Al alloy matrix. Both the discontinuously reinforced aluminum (DRA) and some encapsulated powders (nano-sized SiC or Ta) were used for the second phase emplacement. Through SEM and EDS mapping, the morphology and distribution of second phase particles have been studied. The work shows that friction stir processing is a viable means of producing localized composite zones in Al components.

Polishing process effect on the image of dispersed precipitates

1984 ◽  
Vol 42 ◽  
pp. 534-535
Author(s):  
C.T. Hu ◽  
C.W. Allen
Keyword(s):  
Matrix Material ◽  
Specimen Preparation ◽  
Second Phase ◽  
Precipitate Particle ◽  
Polishing Process ◽  
Second Phase Particles ◽  
The Matrix ◽  
Surface Profiles ◽  
Thinning Process

One important problem in determination of precipitate particle size is the effect of preferential thinning during TEM specimen preparation. Figure 1a schematically represents the original polydispersed Ni3Al precipitates in the Ni rich matrix. The three possible type surface profiles of TEM specimens, which result after electrolytic thinning process are illustrated in Figure 1b. c. & d. These various surface profiles could be produced by using different polishing electrolytes and conditions (i.e. temperature and electric current). The matrix-preferential-etching process causes the matrix material to be attacked much more rapidly than the second phase particles. Figure 1b indicated the result. The nonpreferential and precipitate-preferential-etching results are shown in Figures 1c and 1d respectively.

Analytical Electron Microscopy Study of Second-Phase Particles in 7075 and 7475 Aluminum Alloys

1985 ◽  
Vol 43 ◽  
pp. 348-349
Author(s):  
M. Raghavan ◽  
J. Y. Koo ◽  
J. W. Steeds ◽  
B. K. Park
Keyword(s):  
Aluminum Alloys ◽  
Silicon Oxide ◽  
Analytical Electron Microscopy ◽  
Microscopy Study ◽  
Electron Microscopy Study ◽  
Partial Substitution ◽  
Second Phase ◽  
X Ray ◽  
Second Phase Particles ◽  
Almost All

X-ray microanalysis and Convergent Beam Electron Diffraction (CBD) studies were conducted to characterize the second phase particles in two commercial aluminum alloys -- 7075 and 7475. The second phase particles studied were large (approximately 2-5μm) constituent phases and relatively fine ( ∼ 0.05-1μn) dispersoid particles, Figures 1A and B. Based on the crystal structure and chemical composition analyses, the constituent phases found in these alloys were identified to be Al7Cu2Fe, (Al,Cu)6(Fe,Cu), α-Al12Fe3Si, Mg2Si, amorphous silicon oxide and the modified 6Fe compounds, in decreasing order of abundance. The results of quantitative X-ray microanalysis of all the constituent phases are listed in Table I. The data show that, in almost all the phases, partial substitution of alloying elements occurred resulting in small deviations from the published stoichiometric compositions of the binary and ternary compounds.

Recrystallization in Ultra-Fine Grain Structures of AA3104 Alloy Processed by ECAP and HPT

2012 ◽  
Vol 715-716 ◽  
pp. 346-353
Author(s):  
H. Paul ◽  
T. Baudin ◽  
K. Kudłacz ◽  
A. Morawiec
Keyword(s):  
High Pressure Torsion ◽  
Deformation Mode ◽  
Second Phase ◽  
Orientation Measurement ◽  
Angular Pressing ◽  
Second Phase Particles ◽  
Average Grain Size ◽  
The Matrix ◽  
Electron Microscopes ◽  
Different Strains

The objective of this study was to determine the effect of deformation mode on recrystallization behavior of severely deformed material. Commercial purity AA3104 aluminum alloy was deformed via high pressure torsion and equal channel angular pressing to different strains and then annealed to obtain the state of partial recrystallization. The microstructure and the crystallographic texture were analysed using scanning and transmission electron microscopes equipped with orientation measurement facilities. The nucleation of new grains was observed in bulk recrystallized samples and during in-situ recrystallization in the transmission microscope. Irrespective of the applied deformation mode, a large non-deformable second phase particles strongly influenced strengthening of the matrix through deformation zones around them. It is known that relatively high stored energy stimulates the nucleation of new grains during the recrystalization. In most of the observed cases, the growth of recrystallized grains occurred by the coalescence of neighboring subcells. This process usually led to nearly homogeneous equiaxed grains of similar size. The diameter of grains in the vicinity of large second phase particles was only occasionally significantly larger than the average grain size. Large grains were most often observed in places far from the particles. TEM orientation mapping from highly deformed zones around particles showed that orientations of new grains were not random and only strictly defined groups of orientations were observed.

Microstructure of Friction Stir Processed Mg-Y-Zn Alloy

2007 ◽  
Vol 558-559 ◽  
pp. 777-780 ◽  
Author(s):  
Taiki Morishige ◽  
Masato Tsujikawa ◽  
Sung Wook Chung ◽  
Sachio Oki ◽  
Kenji Higashi
Keyword(s):  
Equal Channel Angular Extrusion ◽  
Second Phase ◽  
Ingot Metallurgy ◽  
Friction Stir ◽  
Fine Grained ◽  
Probe Diameter ◽  
Fine Grain ◽  
Second Phase Particles ◽  
The Matrix ◽  
Zn Alloy

Friction stir processing (FSP) is the effective method of the grain refinement for light metals. The aim of this study is to acquire the fine grained bulk Mg-Y-Zn alloy by ingot metallurgy route much lower in cost. Such bulk alloy can be formed by the superplastic forging. The microstructure of as-cast Mg-Y-Zn alloy was dendrite. The dendrite arm spacing was 72.5 [(m], and there are the lamellar structures in it. FSP was conducted on allover the plate of Mg-Y-Zn alloy for both surfaces by the rotational tool with FSW machine. The stirring passes were shifted half of the probe diameter every execution. The dendrite structures disappeared after FSP, but the lamellar structure could be observed by TEM. The matrix became recrystallized fine grain, and interdendritic second phase particles were dispersed in the grain boundaries. By using FSP, cast Mg-Y-Zn alloy could have fine-grained. This result compared to this material produced by equal channel angular extrusion (ECAE) or rapid-solidified powder metallurgy (RS P/M). As the result, as-FSPed material has the higher hardness than materials produced by the other processes at the similar grain size.

scholarly journals Deformation of Second Phase Particles in Al Alloy Using Severe Plastic Deformation Process

Materia Japan ◽  
2003 ◽  
Vol 42 (12) ◽  
pp. 863-863 ◽  
Author(s):  
Keiichiro Ohishi ◽  
Takeshi Fujita ◽  
Kunihiro Ohashi ◽  
Kenji Kaneko ◽  
Zenji Horita
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Process ◽  
Al Alloy ◽  
Second Phase ◽  
Severe Plastic Deformation Process ◽  
Plastic Deformation Process ◽  
Second Phase Particles

scholarly journals Study on σ Phase in Fe–Al–Cr Alloys

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1092 ◽  
Author(s):  
Jintao Wang ◽  
Shouping Liu ◽  
Xiaoyu Han
Keyword(s):  
Mechanical Properties ◽  
Grain Boundaries ◽  
Grain Growth ◽  
Thermodynamic Calculation ◽  
Second Phase ◽  
Σ Phase ◽  
Austenitic Transformation ◽  
The Matrix ◽  
The Relationship

In this paper, a method of using the second phase to control the grain growth in Fe–Al–Cr alloys was proposed, in order to obtain better mechanical properties. In Fe–Al–Cr alloys, austenitic transformation occurs by adding austenitizing elements, leading to the formation of the second phase and segregation at the grain boundaries, which hinders grain growth. FeCr(σ) phase was obtained in the Fe–Al–Cr alloys, which had grains of several microns and was coherent and coplanar with the matrix (Fe2AlCr). The nucleation of σ phase in Fe–Al–Cr alloy was controlled by the ratio of nickel to chromium. When the Ni/Cr (eq) ratio of alloys was more than 0.19, σ phase could nucleate in Fe–Al–Cr alloy. The relationship between austenitizing and nucleation of FeCr(σ) phase was given by thermodynamic calculation.

Sign in / Sign up

Export Citation Format

Share Document