scholarly journals Complete Design and Finite Element Analysis of an all Terrain Vehicle

2012 ◽  
pp. 276-286
Author(s):  
Amrit Om Nayak ◽  
S. Kalaivanan ◽  
D. Manikandan ◽  
G. Ramkumar ◽  
T. Manoj ◽  
...  
Keyword(s):  
Low Cost ◽  
Cost Effective ◽  
International Standards ◽  
Element Analysis ◽  
Operation And Maintenance ◽  
Successful Design ◽  
Overall Performance ◽  
Function Diagram ◽  
Main Component ◽  
Almost All

We have tried to design an all terrain vehicle that meets international standards and is also cost effective at the same time. We have focused on every single system to improve the performance of each component. Our vehicle can navigate through almost all terrain, which ultimately is the objective behind the making of any all terrain vehicle. We began the task of designing by conducting extensive research of each main component of the vehicle. We did not want to design certain areas such as the frame, and then make the rest to fit. We considered each component to be significant, and thereby designed the vehicle as a whole trying to optimize each component while constantly considering how other components would be affected. This forced us to think outside the box, research more thoroughly, and redesign components along the way in order to have a successful design. We used the necessary parameters to create a Qualitative Function Diagram (QFD) to determine which parameters were the most critical. These key parameters ranging from most critical to least critical are safety, reliability, low cost, ease of operation and maintenance, and overall performance.

Orthophosphate removal from aqueous solutions using drinking-water treatment sludge

2013 ◽  
Vol 68 (8) ◽  
pp. 1757-1762 ◽  
Author(s):  
Krzysztof Piaskowski
Keyword(s):  
Drinking Water ◽  
Water Treatment ◽  
Low Cost ◽  
Drinking Water Treatment ◽  
Cost Effective ◽  
Underground Water ◽  
Iron Hydroxides ◽  
Water Treatment Sludge ◽  
Main Component ◽  
Static Conditions

Drinking-water treatment sludge (DWTS) is a by-product generated during the production of drinking water where iron hydroxides are the main component of the sludge. The aim of the study presented here was to determine the effectiveness of using ferric sludge from two underground water treatment stations to remove orthophosphates from a model solution. The analyses were performed in static conditions. The sludge was dosed in a dry and suspended form. Using sludge dried at room temperature and preparing the suspension again proved to be much less effective in orthophosphate removal than using a suspension brought directly from the station. An increase in process effectiveness with a decreasing pH was observed for all the analysed sludge. Due to the low cost and high capability, DWTS has the potential to be utilised for cost-effective removal of phosphate from wastewater.

scholarly journals Conformally Gated Surface Conducting Behaviors of Single-Walled Carbon Nanotube Thin-Film-Transistors

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3361
Author(s):  
Kyung-Tae Kim ◽  
Keon Woo Lee ◽  
Sanghee Moon ◽  
Joon Bee Park ◽  
Chan-Yong Park ◽  
...  
Keyword(s):  
Field Effect ◽  
Carrier Transport ◽  
Field Effect Transistors ◽  
Low Cost ◽  
Cost Effective ◽  
Electrical Performance ◽  
Solution Synthesis ◽  
Large Area ◽  
Element Analysis ◽  
Single Walled Carbon

Semiconducting single-walled carbon nanotubes (s-SWCNTs) have gathered significant interest in various emerging electronics due to their outstanding electrical and mechanical properties. Although large-area and low-cost fabrication of s-SWCNT field effect transistors (FETs) can be easily achieved via solution processing, the electrical performance of the solution-based s-SWCNT FETs is often limited by the charge transport in the s-SWCNT networks and interface between the s-SWCNT and the dielectrics depending on both s-SWCNT solution synthesis and device architecture. Here, we investigate the surface and interfacial electro-chemical behaviors of s-SWCNTs. In addition, we propose a cost-effective and straightforward process capable of minimizing polymers bound to s-SWCNT surfaces acting as an interfering element for the charge carrier transport via a heat-assisted purification (HAP). With the HAP treated s-SWCNTs, we introduced conformal dielectric configuration for s-SWCNT FETs, which are explored by a carefully designed wide array of electrical and chemical characterizations with finite-element analysis (FEA) computer simulation. For more favorable gate-field-induced surface and interfacial behaviors of s-SWCNT, we implemented conformally gated highly capacitive s-SWCNT FETs with ion-gel dielectrics, demonstrating field-effect mobility of ~8.19 cm2/V⋅s and on/off current ratio of ~105 along with negligible hysteresis.

scholarly journals DEVELOPMENT OF LOW-COST ADDITIVE MANUFACTURING SYSTEM THROUGH SELECTIVE INHIBITION SINTERING (SIS) PROCESS AND EVALUATION OF MECHANICAL CHARACTERISTICS OF FABRICATED PARTS

2020 ◽  
Vol 21 (2) ◽  
pp. 212-229
Author(s):  
Mesfin Sisay Mengesha ◽  
E. Balasubramanian ◽  
P. Arunkumar ◽  
M. Silambarasan ◽  
D. Rajamani
Keyword(s):  
Experimental Investigation ◽  
Additive Manufacturing ◽  
Open Source ◽  
Material Selection ◽  
Low Cost ◽  
Control Unit ◽  
Cost Effective ◽  
Selective Inhibition ◽  
Element Analysis ◽  
Selective Inhibition Sintering

Additive manufacturing (AM) is widely being used in today’s contemporary industry; however, products fabricated by the existing AM techniques are costly due to the high machine cost and low production rate. Therefore, the focus of this work is to design and fabricate a cost-effective and novel powder based selective inhibition sintering (SIS) system. Various subsystems of the machine such as the infrared heater assembly, inhibition deposition mechanism, build and feed tank assemblies, powder deposition, and the compaction system have been indigenously designed and fabricated. An electronic control system is also established through integrating sensors, linear and rotary actuators, belt and pulley mechanism, and temperature feedback control unit. The customized SIS system is developed by integrating the assembly of all the subsystems, and the electronic modules with an open-source platform to generate the necessary motion characteristics. Besides, an open source RepRap user interface firmware has been used to control the machine. Thermo-structural finite element analysis has been used to study the sintering behaviour of powder material. Inhibitor material selection and preparation have been carried out by performing an experimental investigation on the inhibition effects of various materials. The machine has been tested through fabricating parts from HDPE polymer powder. Finally, the performance of the produced parts has been evaluated by conducting an experimental investigation. The results of the investigation indicated that the fabricated parts have attained sufficient mechanical strength and, hence, the developed SIS system can be utilized to manufacture functional parts. ABSTRAK: Industri pembuatan bahan tambahan (AM) banyak digunakan dalam industri kontemporari semasa; walau bagaimanapun, produk yang terhasil daripada teknik sedia ada AM adalah mahal disebabkan harga mesin yang mahal dan kadar penghasilan yang rendah. Oleh itu, tujuan kajian ini adalah bagi mereka cipta serbuk baharu dengan harga berpatutan berdasarkan sistem pensinteran rencatan pilihan (SIS). Pelbagai mesin subsistem seperti pemasangan pemanas inframerah, mekanisme pemendapan rencatan, binaan dan pemasangan tangki suapan, deposisi serbuk, dan sistem pemadatan telah direka cipta secara alami dan dipasang siap. Sistem kawalan elektronik juga diadakan melalui integrasi sensor, lelurus dan penggerak putaran, jaluran dan mekanisme takal dan suhu unit kawalan suap balik. Sistem SIS yang dibuat mengikut pesanan ini dihasilkan dengan mengintegrasi pemasangan kesemua subsistem, dan modul elektronik melalui platfom sumber terbuka bagi menghasilkan ciri-ciri pergerakan bersesuaian. Selain itu, sumber terbuka RepRap perisian tegar antara muka telah digunakan bagi mengawal mesin. Analisis unsur terhingga struktur-terma digunakan bagi mempelajari perihal pensinteran bahan serbuk. Pilihan bahan perencat dan persediaan telah dijalankan dengan menjalankan siasatan eksperimen pada kesan perencat pelbagai bahan. Mesin diuji melalui pemasangan bahagian daripada HDPE serbuk polimer. Akhirnya, bahagian yang terhasil diuji melalui ujian eksperimen. Hasil kajian menunjukkan pemasangan bahagian telah mencapai kekuatan mekanikal mencukupi, dengan itu sistem SIS yang dibina boleh digunakan bagi mengilang bahagian berkaitan.

Material Challenges in Arctic Areas

2007 ◽  
Author(s):  
Agnes Marie Horn ◽  
Per Egil Kvaale ◽  
Mons Hauge
Keyword(s):  
Low Temperature ◽  
Oil And Gas ◽  
Material Selection ◽  
Low Cost ◽  
Cost Effective ◽  
Structural Steels ◽  
Cold Climate ◽  
International Standards ◽  
Pipeline System ◽  
Oil And Gas Exploration

There is a lack of rules and standards that provide guidelines for material selection and qualification of materials for offshore and onshore structures in arctic areas. Many current standards for low temperature applications such as cryogenic piping and process systems do not reflect the need for low-cost bulk materials for large volume applications such as pipelines and production facilities. The growing focus on oil and gas exploration in arctic areas has raised the need for new standards and industry practice that supports cost effective and safe installation and operation of production and transport facilities in the cold climate. There are materials today that are applicable for low temperature conditions. The grades are often highly alloyed (typically 3–9% Ni) with good toughness properties, but these alloys are expensive compared to conventional steel material grades. Such materials may not be applicable in pipelines, structures and process plants. This challenge can be met in two ways. First, structural steels that are capable of being welded and operated in the cold climate should be developed and qualified. Second, materials for forged and casted components that can be welded to the structural steels should be developed and qualified to fit into the integrated structure or pipeline system. Some actions have been taken to develop new standards e.g. within ISO19906, and actions are being taken in Russia to harmonize their specifications with the international standards, but this is a comprehensive job and the work must be executed in parallel with the development of new steels and welding technology.

Prediction of Coal and Biomass Co-Firing in Large Utility Boilers

2011 ◽  
Author(s):  
E. Bar-Ziv ◽  
Z. Steg ◽  
B. Chudnovsky ◽  
A. Talanker ◽  
A. Kunin
Keyword(s):  
Power Plants ◽  
Bituminous Coal ◽  
Low Cost ◽  
Cost Effective ◽  
Capital Costs ◽  
Power Stations ◽  
Operation And Maintenance ◽  
Utility Boilers ◽  
Torrefied Biomass ◽  
Cost Effective Alternative

Co-firing biomass with coal seems a relatively low cost solution to reduce greenhouse gases (GHG) and is also an effective way of taking advantage of the high thermal efficiency of large coal fired boilers. Existing coal-fired power stations can quickly be modified for biomass co-firing achieving considerable levels of renewable generation at low capital costs and low commercial risk. However, certain biomass properties may require the retrofitting of the power plants that were originally designed to operate on a particular bituminous coal. These modifications may decrease the boiler reliability and as result reduce availability and increase operation and maintenance costs. To understand these undesirable effects and determine the optimum way to co-fire biomass in IEC’s 5000 MW coal-fired boilers we studied the effect of biomass co-firing on the capacity, heat transfer surfaces, firing systems, pulverizers, fans and airheaters. We evaluated two biomass alternatives — pelletized biomass and torrefied-biomass (bio-coal) — co-fired with bituminous coals in 575 MW tangentially-fired and 550 MW opposite wall burner boilers. Boiler performance, emission and pulverizer self consumption were discussed. Considering all above aspects, we concluded that the most cost effective alternative is co-firing bio-coal with coal.

ASSESSMENT OF THE PLATELET COUNT IN THE PREGNANT WOMEN IN IGIMS, PATNA, BIHAR

2020 ◽  
Vol 4 (2) ◽  
Author(s):  
Tanwi Singh ◽  
Anshuman Sinha
Keyword(s):  
Platelet Count ◽  
Pregnant Women ◽  
Screening Test ◽  
Low Cost ◽  
Medical Science ◽  
Cost Effective ◽  
Platelet Indices ◽  
Increased Risk ◽  
Low Platelet Count ◽  
Severity Of The Disease

The major risk associated with low platelet count in pregnancy is the increased risk of bleeding during the childbirth or post that. There is an increased blood supply to the uterus during pregnancy and the surgical procedure requires cutting of major blood vessels. Women with thrombocytopenia are at increased risk of losing excessive blood. The risk is more in case of caesarean delivery as compared to vaginal delivery. Hence based on above findings the present study was planned for Assessment of the Platelet Count in the Pregnant Women in IGIMS, Patna, Bihar. The present study was planned in Department of Pathology, Indira Gandhi Institute of Medical Science, Patna, Bihar, India. The present study was planned from duration of January 2019 to June 2019. In the present study 200 pregnant females samples received for the platelet estimation were enrolled in the present study. Clinically platelet indices can be a useful screening test for early identification of preeclampsia and eclampsia. Also platelet indices can assess the prognosis of this disease in pregnant women and can be used as an effective prognostic marker because it correlates with severity of the disease. Platelet count is a simple, low cost, and rapid routine screening test. Hence the data generated from the present study concludes that platelet count can be used as a simple and cost effective tool to monitor the progression of preeclampsia, thereby preventing complications to develop during the gestational period. Keywords: Platelet Count, Pregnant Women, IGIMS, Patna, Bihar, etc.

Parallel Computing for Tire Simulations

2011 ◽  
Vol 39 (3) ◽  
pp. 193-209 ◽  
Author(s):  
H. Surendranath ◽  
M. Dunbar
Keyword(s):  
High Performance ◽  
Effective Means ◽  
Cost Effective ◽  
Turnaround Time ◽  
Careful Consideration ◽  
Rolling Contact ◽  
Element Analysis ◽  
Parallel Solvers ◽  
Design Changes ◽  
Highly Nonlinear

Abstract Over the last few decades, finite element analysis has become an integral part of the overall tire design process. Engineers need to perform a number of different simulations to evaluate new designs and study the effect of proposed design changes. However, tires pose formidable simulation challenges due to the presence of highly nonlinear rubber compounds, embedded reinforcements, complex tread geometries, rolling contact, and large deformations. Accurate simulation requires careful consideration of these factors, resulting in the extensive turnaround time, often times prolonging the design cycle. Therefore, it is extremely critical to explore means to reduce the turnaround time while producing reliable results. Compute clusters have recently become a cost effective means to perform high performance computing (HPC). Distributed memory parallel solvers designed to take advantage of compute clusters have become increasingly popular. In this paper, we examine the use of HPC for various tire simulations and demonstrate how it can significantly reduce simulation turnaround time. Abaqus/Standard is used for routine tire simulations like footprint and steady state rolling. Abaqus/Explicit is used for transient rolling and hydroplaning simulations. The run times and scaling data corresponding to models of various sizes and complexity are presented.

Janus – A New Approach to Air Combat Pilot Training

2019 ◽  
Vol 2019 (4) ◽  
pp. 7-22
Author(s):  
Georges Bridel ◽  
Zdobyslaw Goraj ◽  
Lukasz Kiszkowiak ◽  
Jean-Georges Brévot ◽  
Jean-Pierre Devaux ◽  
...  
Keyword(s):  
Low Cost ◽  
Cost Effective ◽  
High Energy ◽  
Training System ◽  
Embedded Sensors ◽  
Pilot Training ◽  
New Approach ◽  
Combat Aircraft ◽  
Air Combat ◽  
The Cost

Abstract Advanced jet training still relies on old concepts and solutions that are no longer efficient when considering the current and forthcoming changes in air combat. The cost of those old solutions to develop and maintain combat pilot skills are important, adding even more constraints to the training limitations. The requirement of having a trainer aircraft able to perform also light combat aircraft operational mission is adding unnecessary complexity and cost without any real operational advantages to air combat mission training. Thanks to emerging technologies, the JANUS project will study the feasibility of a brand-new concept of agile manoeuvrable training aircraft and an integrated training system, able to provide a live, virtual and constructive environment. The JANUS concept is based on a lightweight, low-cost, high energy aircraft associated to a ground based Integrated Training System providing simulated and emulated signals, simulated and real opponents, combined with real-time feedback on pilot’s physiological characteristics: traditionally embedded sensors are replaced with emulated signals, simulated opponents are proposed to the pilot, enabling out of sight engagement. JANUS is also providing new cost effective and more realistic solutions for “Red air aircraft” missions, organised in so-called “Aggressor Squadrons”.

IFRS IMPLEMENTATION AS ONE OF THE FACTORS FOR IMPROVING THE INVESTMENT CLIMATE IN UKRAINE

2017 ◽  
Author(s):  
Kateryna Sova ◽  
◽  
Natalia Yatsenko ◽  
Denys Zagirniak ◽  
◽  
...  
Keyword(s):  
Financial Reporting ◽  
Direct Investment ◽  
Financial Statements ◽  
International Standards ◽  
Investment Climate ◽  
The European Union ◽  
Economic Activities ◽  
Financial Reporting Standards ◽  
Almost All ◽  
The Impact

The article is devoted to the study of the impact of the introduction of International Financial Reporting Standards (IFRS) on changes in the investment climate in Ukraine. The relevance of the topic is that improving the practice of applying IFRS as a tool for exchanging financial information is one of the key conditions for improving the investment climate in Ukraine. The authors have created the generalized scheme that illustrates the chronological list of enterprises that are required by law to prepare financial statements in accordance with IFRS. It was noted that in 2018, in accordance with Part 2 of Article 12 of the law on accounting and financial reporting in Ukraine and resolution of the Cabinet of Ministers of Ukraine No. 547 from 11.07.2018, the criteria of enterprises that are required to prepare financial statements in accordance with IFRS were updated. This step significantly increased the level of application of international standards due to the adoption of such a decision at the legislative level. The dynamics of the number of IFRS enterprises in Ukraine was analyzed. The analysis showed that over the past three years, the number of almost all enterprises that must apply international standards has been growing. The advantages of using IFRS for different users of financial statements were determined. It was determined that the priority users of IFRS financial statements are investors. At the same time, it was noted that the main advantage for other users of financial statements prepared in accordance with international standards is the improvement of the investment climate. The dynamics of the Investment Attractiveness Index of Ukraine based on the Likert scale in the period from 2016 to 2020 was analyzed. The direct investment receipts to Ukraine from the European Union countries were studied. The dynamics of direct investment in the Ukrainian economy was analyzed for two types of economic activities that should form financial statements in accordance with IFRS, namely, the extractive industry and quarrying, as well as financial and insurance activities.

Application of Natural Dye Obtained from Sweet Indrajao on Fabrics

2020 ◽  
Vol 6 (3) ◽  
pp. 180-191
Author(s):  
Kavitha Chandrasekaran
Keyword(s):  
Potassium Dichromate ◽  
Bacterial Pathogens ◽  
Ultrasonic Method ◽  
Ferrous Sulphate ◽  
Fine Powder ◽  
Cost Effective ◽  
Metal Salts ◽  
Cow Dung ◽  
Long Run ◽  
Almost All

Background:: In the long run, synthetic tints were found to be harmful to the chemicals. As a result natural tints have come to be used for their many intrinsic values. The main reason being, then availability of local plants as the main source of natural colorants. Their easy availability in the country being zero cost – effective and planted for other purposes are the main reasons for utilizing them as natural tints. Almost all the parts of the plants, namely stem, leaves, fruits, seeds, barks etc. are used for extracting natural colour. In addition, they are antimicrobial antifungal, insect – repellant deodorant, disinfectant having medicinal values. Methods:: Sweet Indrajao leaves were cleaned by washing with water and dried under direct sunlight and ground as fine powder. A fine strainer was used to remove the wastages. After all these processes, 1-kilogram leaves weighed 318 grams. Then, it is put in 75% ethanol 25% water and heated in a breaker which in kept over a water bath for 2 hours. After this, the contents were filtered and kept in a separate beaker. Bleached fleece draperies stained with stain extract were made to become wet and put into different stain baths which contain the required amount of stain extract and water. Acetic acid was added to it after 20 minutes. The fleece drapery was stained for about one hour at 60oC. The draperies thus stained were removed, squeezed, and put to treatment with metal salts without washing. Different metal salts were used for the treatment using 3% of any one of the chemical mordants like alum, stannous chloride, potassium dichromate, ferrous sulphate, nickel sulphate, copper sulphate and natural mordants such as myrobolan, turmeric, cow dung, Banana sap juice at 60oC for 30 minutes with MLR of 1:30. The stained draperies were washed repeatedly in all the three methods in water and dried in air. At last, the stained draperies were put to soap with soap solution at 60oC for 10 minutes. The draperies were repeatedly washed in water and dried under the sun. Results:: Sweet Indrajao leaves discharged colour easily in alcoholic water. The fleece draperies were stained with chemical and natural mordants. It was observed that the stain uptake was found to be good in post-mordanting method. Ultrasonication has clearly improved the stainability of the draperies at pH 3 and 3.5 values. The pH decreases the stain ability under both Conventional and Ultrasonic conditions. The colour strength increases with an increase in staining temperature in both cases of US and CH methods. Conclusion:: Sweet Indrajao.L has been found to have good ultrasonic potential as a stain plant. The stain uptake as well as the fastness properties of the fleece drapery were found to enhance when metal mordant was used in conjugation with ultra-sonication for the extract of Sweet Indrajao. It was also found that the enhancement of staining ability was better without mordant draperies. The dye extract showed good antibacterial activity against the three bacterial pathogens. Among the three bacterial pathogens, dye extract showed more effective against Escherichia coli pathogens and dye extract showed more effective against Aspergillus pathogens. Hence, the ultrasonic method of drapery staining may be appropriate and beneficial for society at large in future.

Sign in / Sign up

Export Citation Format

Share Document