The Effect of Belt-Drive CVT Fluid on the Friction Coefficient Between Metal Components

1997 ◽  
Author(s):  
Takao Ishikawa ◽  
Yasuhiro Murakami ◽  
Rika Yauchibara ◽  
Akio Sano
Keyword(s):  
Friction Coefficient ◽  
Belt Drive

Finite Element Model of Schallamach Waves in Belt-Drives

2019 ◽  
Author(s):  
Mohammed Khattab ◽  
Tamer Wasfy
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Finite Element Model ◽  
Wave Phenomenon ◽  
Coulomb Friction ◽  
Element Model ◽  
Belt Drive ◽  
High Fidelity ◽  
Stick Slip ◽  
Belt Drives

Abstract The objective of this study is to investigate if a high-fidelity finite element model can predict the Schallamach wave phenomenon in belt-drives. To this end a computational model which closely mimics a recently developed one-pulley experimental belt-drive apparatus, was created. The dynamic response predicted by the model is compared to the experiment results in order to demonstrate that the model can be used to predict the Schallamach wave phenomenon. Furthermore, the model is used to investigate the roles of Coulomb friction coefficient, adhesion, and torque direction on stick-slip instability effects.

Microstructure and Friction of Ion Beam Induced Amorphous Ti-Pd Alloys

1985 ◽  
Vol 55 ◽  
Author(s):  
J-P. Hirvonen ◽  
M. Nastasi ◽  
J. R. Phillips ◽  
J. W. Mayer
Keyword(s):  
Solid Solution ◽  
Friction Coefficient ◽  
Composition Range ◽  
Ion Beam ◽  
Amorphous Region ◽  
Transmission Electron ◽  
Solid Solution Region ◽  
Friction Measurements ◽  
Solution Region ◽  
High Equilibrium

ABSTRACTMultilayered samples of Ti-Pd with linearly varying compositions were irradiated by Xe ions at 600 keV. The induced microstructures were studied by using transmission electron microscopy and Rutherford backscattering. Mixing was found to be complete over the entire composition range, resulting in amorphous or amorphous plus crystalline structures except at the palladium-rich end, where a crystalline Pd-Ti solid solution was obtained. This is consistent with the high equilibrium solubility of Ti in Pd. In addition, significant coarsening of the microstructure caused by irradiation was found in this solid solution region.Friction measurements were carried out in air and water by using a polytetrafluoroethylene pin as a counterpart. In air the friction coefficient was independent of composition and microstructure after about 2000 passes. In water, however, after 600 passes the friction coefficient reached a steady-state value with a pronounced minimum over the amorphous region. This property was unchanged throughout the remaining 10000 passes.

A Quantitative Theory for the Computation of Tire Friction Under Severe Conditions of Sliding

1986 ◽  
Vol 14 (1) ◽  
pp. 44-72 ◽  
Author(s):  
C. M. Mc C. Ettles
Keyword(s):  
Friction Coefficient ◽  
Flash Temperature ◽  
Contact Conditions ◽  
Quantitative Form ◽  
Heating Effects ◽  
Rubber Friction ◽  
Viscoelastic Effects ◽  
Tire Friction ◽  
Pavement Friction ◽  
Metal Polymer

Abstract It is proposed that tire-pavement friction is controlled by thermal rather than by hysteresis and viscoelastic effects. A numerical model of heating effects in sliding is described in which the friction coefficient emerges as a dependent variable. The overall results of the model can be expressed in a closed form using Blok's flash temperature theory. This allows the factors controlling rubber friction to be recognized directly. The model can be applied in quantitative form to metal-polymer-ice contacts. Several examples of correlation are given. The difficulties of characterizing the contact conditions in tire-pavement friction reduce the model to qualitative form. Each of the governing parameters is examined in detail. The attainment of higher friction by small, discrete particles of aluminum filler is discussed.

Sign in / Sign up

Export Citation Format

Share Document