The Emission of a Diesel Engine in Different Coolant Temperature during Cold Start at High Altitude

2019 ◽  
Author(s):  
Liang Fang ◽  
Diming Lou ◽  
Zhiyuan Hu ◽  
Piqiang Tan
Keyword(s):  
Diesel Engine ◽  
High Altitude ◽  
Cold Start ◽  
Coolant Temperature

scholarly journals Engine Performance and Emissions Analysis in a Cold, Intermediate and Hot Start Diesel Engine

2020 ◽  
Vol 10 (11) ◽  
pp. 3839 ◽  
Author(s):  
Faisal Lodi ◽  
Ali Zare ◽  
Priyanka Arora ◽  
Svetlana Stevanovic ◽  
Mohammad Jafari ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Cold Start ◽  
Lubricating Oil ◽  
Coolant Temperature ◽  
Effective Pressure ◽  
Warm Up ◽  
Hot Start ◽  
Depth Analysis ◽  
Performance And Emissions ◽  
The Impact

Presented in this paper is an in-depth analysis of the impact of engine start during various stages of engine warm up (cold, intermediate, and hot start stages) on the performance and emissions of a heavy-duty diesel engine. The experiments were performed at constant engine speeds of 1500 and 2000 rpm on a custom designed drive cycle. The intermediate start stage was found to be longer than the cold start stage. The oil warm up lagged the coolant warm up by approximately 10 °C. During the cold start stage, as the coolant temperature increased from ~25 to 60 °C, the brake specific fuel consumption (BSFC) decreased by approximately 2% to 10%. In the intermediate start stage, as the coolant temperature reached 70 °C and the injection retarded, the indicated mean effective pressure (IMEP) and the brake mean effective pressure (BMEP) decreased by approximately 2% to 3%, while the friction mean effective pressure (FMEP) decreased by approximately 60%. In this stage, the NOx emissions decreased by approximately 25% to 45%, while the HC emissions increased by approximately 12% to 18%. The normalised FMEP showed that higher energy losses at lower loads were most likely contributing to the heating of the lubricating oil.

Effect of altitude conditions on combustion and performance of a turbocharged direct-injection diesel engine

2021 ◽  
pp. 095440702110262
Author(s):  
Zhentao Liu ◽  
Jinlong Liu
Keyword(s):  
Diesel Engine ◽  
High Altitude ◽  
Diesel Engines ◽  
Direct Injection ◽  
Pressure Rise ◽  
Ambient Conditions ◽  
Allowable Limit ◽  
Spray Formation ◽  
Direct Injection Diesel Engine ◽  
And Performance

Market globalization necessitates the development of heavy duty diesel engines that can operate at altitudes up to 5000 m without significant performance deterioration. But the current scenario is that existing studies on high altitude effects are still not sufficient or detailed enough to take effective measures. This study applied a single cylinder direct injection diesel engine with simulated boosting pressure to investigate the performance degradation at high altitude, with the aim of adding more knowledge to the literature. Such a research engine was conducted at constant speed and injection strategy but different ambient conditions from sea level to 5000 m in altitude. The results indicated the effects of altitude on engine combustion and performance can be summarized as two aspects. First comes the extended ignition delay at high altitude, which would raise the rate of pressure rise to a point that can exceed the maximum allowable limit and therefore shorten the engine lifespan. The other disadvantage of high-altitude operation is the reduced excess air ratio and gas density inside cylinder. Worsened spray formation and mixture preparation, together with insufficient and late oxidation, would result in reduced engine efficiency, increased emissions, and power loss. The combustion and performance deteriorations were noticeable when the engine was operated above 4000 m in altitude. All these findings support the need for further fundamental investigations of in-cylinder activities of diesel engines working at plateau regions.

EGR cylinder deactivation strategy to accelerate the warm-up and restart processes in a Diesel engine operating at cold conditions

2021 ◽  
pp. 146808742110395
Author(s):  
José Galindo ◽  
Vicente Dolz ◽  
Javier Monsalve-Serrano ◽  
Miguel Angel Bernal Maldonado ◽  
Laurent Odillard
Keyword(s):  
Steady State ◽  
Diesel Engine ◽  
Internal Combustion Engines ◽  
Cold Start ◽  
Pollutant Emissions ◽  
Oxidation Catalyst ◽  
Maximum Efficiency ◽  
Warm Up ◽  
Cylinder Deactivation ◽  
The Impact

The aftertreatment systems used in internal combustion engines need high temperatures for reaching its maximum efficiency. By this reason, during the engine cold start period or engine restart operation, excessive pollutant emissions levels are emitted to the atmosphere. This paper evaluates the impact of using a new cylinder deactivation strategy on a Euro 6 turbocharged diesel engine running under cold conditions (−7°C) with the aim of improving the engine warm-up process. This strategy is evaluated in two parts. First, an experimental study is performed at 20°C to analyze the effect of the cylinder deactivation strategy at steady-state and during an engine cold start at 1500 rpm and constant load. In particular, the pumping losses, pollutant emissions levels and engine thermal efficiency are analyzed. In the second part, the engine behavior is analyzed at steady-state and transient conditions under very low ambient temperatures (−7°C). In these conditions, the results show an increase of the exhaust temperatures of around 100°C, which allows to reduce the diesel oxidation catalyst light-off by 250 s besides of reducing the engine warm-up process in approximately 120 s. This allows to reduce the CO and HC emissions by 70% and 50%, respectively, at the end of the test.

Simulation of a Single Cylinder Diesel Engine Under Cold Start Conditions Using Simulink

2000 ◽  
Vol 123 (1) ◽  
pp. 117-124 ◽  
Author(s):  
H.-Q. Liu ◽  
N. G. Chalhoub ◽  
N. Henein
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Cold Start ◽  
Operating Conditions ◽  
Combustion Model ◽  
Nonlinear Dynamic Model ◽  
Single Cylinder ◽  
Engine Model ◽  
Simulink Model ◽  
Engine Components

A nonlinear dynamic model is developed in this study to simulate the overall performance of a naturally aspirated, single cylinder, four-stroke, direct injection diesel engine under cold start and fully warmed-up conditions. The model considers the filling and emptying processes of the cylinder, blowby, intake, and exhaust manifolds. A single zone combustion model is implemented and the heat transfer in the cylinder, intake, and exhaust manifolds are accounted for. Moreover, the derivations include the dynamics of the crank-slider mechanism and employ an empirical model to estimate the instantaneous frictional losses in different engine components. The formulation is coded in modular form whereby each module, which represents a single process in the engine, is introduced as a single block in an overall Simulink engine model. The numerical accuracy of the Simulink model is verified by comparing its results to those generated by integrating the engine formulation using IMSL stiff integration routines. The engine model is validated by the close match between the predicted and measured cylinder gas pressure and engine instantaneous speed under motoring, steady-state, and transient cold start operating conditions.

Experimental analysis of the influence of coolant and oil temperature on combustion and emissions in an automotive diesel engine

2018 ◽  
Vol 20 (2) ◽  
pp. 247-260 ◽  
Author(s):  
Xavier Tauzia ◽  
Alain Maiboom ◽  
Hassan Karaky ◽  
Pascal Chesse
Keyword(s):  
Particulate Matter ◽  
Diesel Engine ◽  
Control Unit ◽  
Operating Conditions ◽  
Volumetric Efficiency ◽  
Coolant Temperature ◽  
Lower Efficiency ◽  
Combustion Heat ◽  
Hydrocarbon Emission ◽  
Energy Share

Since many trips are of short duration and include a cold start, automotive engines run quite often without having reached their nominal temperature. This is known to have some major drawbacks, such as increased fuel consumption and higher emissions due to lower efficiency of after-treatment devices, but detailed description of these various effects is seldom presented in the literature. In this article, experiments were conducted on an automotive diesel engine by varying independently the coolant and oil temperatures between 30 °C and 90 °C. Three different operating conditions (low, mid and full load) were studied. The experimental set-up is briefly described as well as the uncertainty of the associated measurements and the development of analytic tools. Then, the evolution of volumetric efficiency, energy share, combustion heat release and exhaust emissions (NOx, particulate matter, CO, unburned hydrocarbons) are described in detail and analysed. Several strategies were considered, including some corrections used in the standard engine control unit to compensate for the low coolant temperature. Some effects of the coolant and oil temperature reduction were clear: increase in friction losses, volumetric efficiency and ignition delay and decrease in NOx emissions. On the contrary, the evolution of brake thermal efficiency, particulate matter, CO and unburned hydrocarbon emission depended on the operating point.

Sign in / Sign up

Export Citation Format

Share Document