scholarly journals Engine Performance and Emissions Analysis in a Cold, Intermediate and Hot Start Diesel Engine

2020 ◽  
Vol 10 (11) ◽  
pp. 3839 ◽  
Author(s):  
Faisal Lodi ◽  
Ali Zare ◽  
Priyanka Arora ◽  
Svetlana Stevanovic ◽  
Mohammad Jafari ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Cold Start ◽  
Lubricating Oil ◽  
Coolant Temperature ◽  
Effective Pressure ◽  
Warm Up ◽  
Hot Start ◽  
Depth Analysis ◽  
Performance And Emissions ◽  
The Impact

Presented in this paper is an in-depth analysis of the impact of engine start during various stages of engine warm up (cold, intermediate, and hot start stages) on the performance and emissions of a heavy-duty diesel engine. The experiments were performed at constant engine speeds of 1500 and 2000 rpm on a custom designed drive cycle. The intermediate start stage was found to be longer than the cold start stage. The oil warm up lagged the coolant warm up by approximately 10 °C. During the cold start stage, as the coolant temperature increased from ~25 to 60 °C, the brake specific fuel consumption (BSFC) decreased by approximately 2% to 10%. In the intermediate start stage, as the coolant temperature reached 70 °C and the injection retarded, the indicated mean effective pressure (IMEP) and the brake mean effective pressure (BMEP) decreased by approximately 2% to 3%, while the friction mean effective pressure (FMEP) decreased by approximately 60%. In this stage, the NOx emissions decreased by approximately 25% to 45%, while the HC emissions increased by approximately 12% to 18%. The normalised FMEP showed that higher energy losses at lower loads were most likely contributing to the heating of the lubricating oil.

scholarly journals Combustion Analysis of a Diesel Engine during Warm up at Different Coolant and Lubricating Oil Temperatures

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3931
Author(s):  
Faisal Lodi ◽  
Ali Zare ◽  
Priyanka Arora ◽  
Svetlana Stevanovic ◽  
Mohammad Jafari ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Ignition Delay ◽  
Peak Pressure ◽  
Cold Start ◽  
Lubricating Oil ◽  
Combustion Model ◽  
Injection Timing ◽  
Warm Up ◽  
Combustion Duration ◽  
Hot Start

A comprehensive analysis of combustion behaviour during cold, intermediately cold, warm and hot start stages of a diesel engine are presented. Experiments were conducted at 1500 rpm and 2000 rpm, and the discretisation of engine warm up into stages was facilitated by designing a custom drive cycle. Advanced injection timing, observed during the cold start period, led to longer ignition delay, shorter combustion duration, higher peak pressure and a higher peak apparent heat release rate (AHRR). The peak pressure was ~30% and 20% and the AHRR was ~2 to 5% and ±1% higher at 1500 rpm and 2000 rpm, respectively, during cold start, compared to the intermediate cold start. A retarded injection strategy during the intermediate cold start phase led to shorter ignition delay, longer combustion duration, lower peak pressure and lower peak AHRR. At 2000 rpm, an exceptional combustion behaviour led to a ~27% reduction in the AHRR at 25% load. Longer ignition delays and shorter combustion durations at 25% load were observed during the intermediately cold, warm and hot start segments. The mass fraction burned (MFB) was calculated using a single zone combustion model to analyse combustion parameters such as crank angle (CA) at 50% MFB, AHRR@CA50 and CA duration for 10–90% MFB.

EGR cylinder deactivation strategy to accelerate the warm-up and restart processes in a Diesel engine operating at cold conditions

2021 ◽  
pp. 146808742110395
Author(s):  
José Galindo ◽  
Vicente Dolz ◽  
Javier Monsalve-Serrano ◽  
Miguel Angel Bernal Maldonado ◽  
Laurent Odillard
Keyword(s):  
Steady State ◽  
Diesel Engine ◽  
Internal Combustion Engines ◽  
Cold Start ◽  
Pollutant Emissions ◽  
Oxidation Catalyst ◽  
Maximum Efficiency ◽  
Warm Up ◽  
Cylinder Deactivation ◽  
The Impact

The aftertreatment systems used in internal combustion engines need high temperatures for reaching its maximum efficiency. By this reason, during the engine cold start period or engine restart operation, excessive pollutant emissions levels are emitted to the atmosphere. This paper evaluates the impact of using a new cylinder deactivation strategy on a Euro 6 turbocharged diesel engine running under cold conditions (−7°C) with the aim of improving the engine warm-up process. This strategy is evaluated in two parts. First, an experimental study is performed at 20°C to analyze the effect of the cylinder deactivation strategy at steady-state and during an engine cold start at 1500 rpm and constant load. In particular, the pumping losses, pollutant emissions levels and engine thermal efficiency are analyzed. In the second part, the engine behavior is analyzed at steady-state and transient conditions under very low ambient temperatures (−7°C). In these conditions, the results show an increase of the exhaust temperatures of around 100°C, which allows to reduce the diesel oxidation catalyst light-off by 250 s besides of reducing the engine warm-up process in approximately 120 s. This allows to reduce the CO and HC emissions by 70% and 50%, respectively, at the end of the test.

Impact of military JP-8 fuel on heavy-duty diesel engine performance and emissions

2007 ◽  
Vol 221 (8) ◽  
pp. 957-970 ◽  
Author(s):  
G Fernandes ◽  
J Fuschetto ◽  
Z Filipi ◽  
D Assanis ◽  
H McKee
Keyword(s):  
Particulate Matter ◽  
Diesel Engine ◽  
Fuel Economy ◽  
Engine Performance ◽  
Heavy Duty ◽  
Heavy Duty Diesel Engine ◽  
Performance And Emissions ◽  
Heavy Duty Diesel ◽  
Engine Performance And Emissions ◽  
The Impact

Investigating the impact of jet fuel on diesel engine performance and emissions is very important for military vehicles, due to the US Army Single Fuel Forward Policy mandating that deployed vehicles must refuel with aviation fuel JP-8. There is a known torque and fuel economy penalty associated with the operation of a diesel engine with JP-8 fuel, due to its lower density and viscosity. On the other hand, a few experimental studies have suggested that kerosene-based fuels have the potential for lowering exhaust emissions, especially particulate matter, compared to diesel fuel #2 (DF-2). However, studies so far have typically focused on quantifying the effects of simply replacing the regular DF-2 with JP-8, rather than fully investigating the reasons behind the observed differences. This research evaluates the effect of using JP-8 fuel in a heavy-duty diesel engine on fuel injection, combustion, performance, and emissions, and subsequently utilizes the obtained insight to propose changes to the engine calibration to mitigate the impact of the trade-offs. Experiments were carried out on a Detroit Diesel Corporation (DDC) S60 engine outfitted with exhaust gas recirculation (EGR). The results indicate that torque and fuel economy of diesel fuel can be matched, without smoke or NO x penalty, by increasing the duration of injection to compensate for the lower fuel density. The lower cetane number of JP-8 caused an increased ignition delay and increased premixed combustion, and their cumulative effect led to relatively unchanged combustion phasing. Under almost all conditions, JP-8 led to lower NO x and particulate matter (PM) emissions and shifted the NO x-PM trade-off favourably.

Development of control strategy for fast idling condition of diesel engine based on target torque

2021 ◽  
Vol 13 (12) ◽  
pp. 168781402110626
Author(s):  
Jiesong Jian ◽  
Xuedong Lin ◽  
Yuanchun Ren ◽  
Yingchao Zhang ◽  
Chun Shen ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Economy ◽  
Control Strategy ◽  
Cold Start ◽  
Maximum Speed ◽  
Fuel Saving ◽  
Time Saving ◽  
Warm Up

This article puts forward the concept of fast idling condition. The comparative experiments of idling and fast idling warming up engine show that: during cold start, the warm-up of fast idling condition whose maximum speed is 1350 r/min is the most fuel-efficient, fuel-saving about 4.5%, time-saving about 32.5%; at normal temperature, warming up engine of fast idling condition does not save fuel. The warm-up experiments of fast idling condition that accelerations are different in the descent phase show that when the engine is cold, the smaller the acceleration in the descent phase of fast idling condition is, the more time and fuel are saved; at normal temperature, the bigger the acceleration in the descent phase of fast idling condition is, the better the fuel economy is. Therefore, it is inferred that the engine should be warmed up under fast idling condition when the engine is cold and idling condition is used to warm up engine at normal temperature. To sum up, when the engine is cold, the engine should be warmed up under the fast idling condition whose maximum speed is 1350 r/min; at normal temperature, it should be warmed up in idling condition to save fuel.

scholarly journals Diesel engine emissions with oxygenated fuels: A comparative study into cold-start and hot-start operation

2017 ◽  
Vol 162 ◽  
pp. 997-1008 ◽  
Author(s):  
Ali Zare ◽  
Md Nurun Nabi ◽  
Timothy A. Bodisco ◽  
Farhad M. Hossain ◽  
M.M. Rahman ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Comparative Study ◽  
Cold Start ◽  
Engine Emissions ◽  
Diesel Engine Emissions ◽  
Hot Start ◽  
Oxygenated Fuels
Sign in / Sign up

Export Citation Format

Share Document