Improved Thermal Efficiency using Hydrous Ethanol Reforming in Advanced Spark-Ignition Engines

2016 ◽  
Author(s):  
Atsushi Shimada ◽  
Yuzo Shirakawa ◽  
Takao Ishikawa
Keyword(s):  
Thermal Efficiency ◽  
Spark Ignition ◽  
Spark Ignition Engines ◽  
Ethanol Reforming ◽  
Hydrous Ethanol

scholarly journals The Operating Features of a Stoichiometric, Ammonia and Gasoline Dual Fueled Spark Ignition Engine

2006 ◽  
Author(s):  
Shawn M. Grannell ◽  
Dennis N. Assanis ◽  
Stanislav V. Bohac ◽  
Donald E. Gillespie
Keyword(s):  
Compression Ratio ◽  
Thermal Efficiency ◽  
Maximum Load ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Gaseous Ammonia ◽  
Spark Ignition Engines ◽  
Stoichiometric Mixture ◽  
Brake Thermal Efficiency ◽  
Practical Operation

An overall stoichiometric mixture of air, gaseous ammonia and gasoline was metered into a single cylinder, variable compression ratio, supercharged CFR engine at varying ratios of gasoline to ammonia. The engine was operated such that the combustion was knock-free with minimal roughness for all loads ranging from idle up to a maximum load in the supercharge regime. For a given load, speed, and compression ratio there was a range of ratios of gasoline to ammonia for which knock-free, smooth firing was obtained. This range was investigated at its roughness limit and also at its knock limit. If too much ammonia was used, then the engine fired with an excessive roughness. If too much gasoline was used, then knock-free combustion could not be obtained while the maximum brake torque spark advance was maintained. Stoichiometric operation on gasoline alone was also investigated, for comparison. It was found that a significant fraction of the gasoline used in spark ignition engines could be replaced with ammonia. Operation on mostly gasoline was required near idle. However, mostly ammonia could be used at high load. Operation on ammonia alone was possible at some of the supercharged load points. Generally, the use of ammonia or ammonia with gasoline allowed knock-free operation at higher compression ratios and higher loads than could be obtained with the use of gasoline alone. The use of ammonia/gasoline allowed practical operation at a compression ratio of 12:1 whereas the limit for gasoline alone was 9:1. When running on ammonia/gasoline the engine could be operated at brake mean effective pressures that were more than 50% higher than those achieved with the use of gasoline alone. The maximum brake thermal efficiency achieved with the use of ammonia/gasoline was 32.0% at 10:1 compression ratio and BMEP = 1025 kPa. The maximum brake thermal efficiency possible for gasoline was 24.6% at 9:1 and BMEP = 570 kPa.

Water-Ethanol-Gasoline Blends—Physical Properties, Power, and Pollution Characteristics

1984 ◽  
Vol 106 (4) ◽  
pp. 841-848 ◽  
Author(s):  
S. Rajan
Keyword(s):  
Physical Properties ◽  
Thermal Efficiency ◽  
Spark Ignition ◽  
Spark Ignition Engines ◽  
Oxides Of Nitrogen ◽  
Engine Operation ◽  
Nitrogen Emissions ◽  
Pollution Characteristics ◽  
The Road ◽  
On The Road

Factors relevant to the utilization of nonanhydrous ethanol as a blending component with gasoline for use in current on-the-road spark ignition engines are investigated. Miscibility limits are determined and key physical properties important for proper engine operation are measured. Dynamometer tests on an unmodified production engine with hydrated ethanol-gasoline blends containing varying percentages of water show potential for increased thermal efficiency and reduced oxides of nitrogen emissions.

A predictive model for knock onset in spark-ignition engines using hydrous ethanol

2017 ◽  
Author(s):  
Francisco Renato dos Santos Junior ◽  
Caio Rufino ◽  
Janito Vaqueiro Ferreira
Keyword(s):  
Predictive Model ◽  
Spark Ignition ◽  
Spark Ignition Engines ◽  
Hydrous Ethanol

scholarly journals Detailed Experimental Investigation of A Spark Ignition Engine in A Wide Range of Work

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Melih Yıldız ◽  
Bilge Albayrak Çeper
Keyword(s):  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Heat Dissipation ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Engine Fuel ◽  
Spark Ignition Engines ◽  
Combustion Control ◽  
Wide Range

For years, the goal of vehicle manufacturers; combustion control of spark ignition engines, ease of passage between the various cycles For years, the goal of vehicle manufacturers; combustion control of spark ignition engines, ease of passage between the various cycles, low emission values of diesel engines, high fuel economy and output power, thereby achieving optimum values in internal combustion engines. In this context, to improve the engine performance and increase the volumetric and thermal efficiency of the engine in all operating conditions to minimize the power losses and to reduce the exhaust emissions in order to obtain the maximum power, most economical and without environmental pollution, continues to be updated. In this study, the optimum working map of the engine was obtained by considering the power, torque, specific fuel consumption, cylinder pressure, exhaust gas temperature, thermal efficiency, average effective pressure, heat dissipation rate and emissions of four stroke, two cylinder, spark ignition SI engine fuel.

Sign in / Sign up

Export Citation Format

Share Document