Non-Linear Analysis of the Combustion Process in Compression-Ignition Direct Injection Engines of Non-Road Vehicles with the Use of Vibroacoustic Processes in the Point of View of the OBD III Engine Diagnostics

2011 ◽  
Author(s):  
Jerzy Merkisz ◽  
Marek Waligorski ◽  
Maciej Bajerlein ◽  
Jaroslaw Markowski
Keyword(s):  
Direct Injection ◽  
Combustion Process ◽  
Linear Analysis ◽  
Point Of View ◽  
Compression Ignition ◽  
Road Vehicles ◽  
Direct Injection Engines ◽  
Non Linear

An integrated effort of medium reactivity fuel, in-cylinder, and after-treatment strategies to demonstrate potential reduction in challenging emissions of reactivity controlled compression ignition combustion

2019 ◽  
Vol 234 (5) ◽  
pp. 1260-1278
Author(s):  
R Murugan ◽  
D Ganesh ◽  
G Nagarajan
Keyword(s):  
Carbon Monoxide ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Process ◽  
Oxidation Catalyst ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Potential Reduction ◽  
Carbon Monoxide Emission ◽  
Compression Ignition Combustion

Previous studies on reactivity controlled compression ignition combustion indicated that, reducing the hydrocarbon and carbon monoxide emissions at low load conditions still remains a challenge because of lower in-cylinder temperatures due to lower global reactivity gradient and reduced oxidation process. Research in this direction has not been reported so far and with this motivation, an attempt has been made to increase the global reactivity gradient and oxidation of fuel–air mixture by converting the low reactivity fuel methanol into medium reactivity fuel. This is achieved by mixing high octane oxygenated fuel, methanol (Octane Number: 110), with an oxygenated better cetane and volatility fuels like polyoxymethylene dimethyl ether (Cetane Number: 78) and isobutanol (Cetane Number: 15). The medium reactivity fuel with multiple direct injection of diesel fuel timed the combustion of dual fuel–air mixture to avoid too late or too advanced combustion which are the prime factors in controlling the unburnt emissions in a low temperature combustion process. Four medium reactivity fuel samples, M80IB20, M60IB40, M90P10, and M80P20, on percentage volume basis have been prepared and tested on the modified on-road three-cylinder turbocharged common rail direct injection diesel engine to demonstrate higher indicated thermal efficiency and potential reduction in unburnt and oxides of nitrogen/particulate matter emissions from reactivity controlled compression ignition combustion. Experimental results show that, use of medium reactivity fuel with optimized diesel injection strategy resulted in 66% decrease in hydrocarbon emission and 74% decrease in carbon monoxide emission by enhancing the oxidation of fuel–air mixture at lower temperatures which is evidently noticed in the combustion characteristics. Further reduction in hydrocarbon and carbon monoxide emission of about 90% has been achieved by integrating the diesel oxidation catalyst with the engine.

scholarly journals Isolating the effects of reactivity stratification in reactivity-controlled compression ignition with iso-octane and n-heptane on a light-duty multi-cylinder engine

2017 ◽  
Vol 19 (9) ◽  
pp. 907-926 ◽  
Author(s):  
Martin L Wissink ◽  
Scott J Curran ◽  
Greg Roberts ◽  
Mark PB Musculus ◽  
Christine Mounaïm-Rousselle
Keyword(s):  
High Efficiency ◽  
Direct Injection ◽  
Combustion Process ◽  
High Reactivity ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Fundamental Understanding ◽  
Primary Reference ◽  
Primary Reference Fuels

Reactivity-controlled compression ignition (RCCI) is a dual-fuel variant of low-temperature combustion that uses in-cylinder fuel stratification to control the rate of reactions occurring during combustion. Using fuels of varying reactivity (autoignition propensity), gradients of reactivity can be established within the charge, allowing for control over combustion phasing and duration for high efficiency while achieving low NOx and soot emissions. In practice, this is typically accomplished by premixing a low-reactivity fuel, such as gasoline, with early port or direct injection, and by direct injecting a high-reactivity fuel, such as diesel, at an intermediate timing before top dead center. Both the relative quantity and the timing of the injection(s) of high-reactivity fuel can be used to tailor the combustion process and thereby the efficiency and emissions under RCCI. While many combinations of high- and low-reactivity fuels have been successfully demonstrated to enable RCCI, there is a lack of fundamental understanding of what properties, chemical or physical, are most important or desirable for extending operation to both lower and higher loads and reducing emissions of unreacted fuel and CO. This is partly due to the fact that important variables such as temperature, equivalence ratio, and reactivity change simultaneously in both a local and a global sense with changes in the injection of the high-reactivity fuel. This study uses primary reference fuels iso-octane and n-heptane, which have similar physical properties but much different autoignition properties, to create both external and in-cylinder fuel blends that allow for the effects of reactivity stratification to be isolated and quantified. This study is part of a collaborative effort with researchers at Sandia National Laboratories who are investigating the same fuels and conditions of interest in an optical engine. This collaboration aims to improve our fundamental understanding of what fuel properties are required to further develop advanced combustion modes.

scholarly journals Diagnosing of misfire events in compression-ignition engines with the help of vibroacoustic methods in the aspect of OBD system application in diesel locomotives

2008 ◽  
Vol 132 (1) ◽  
pp. 3-16
Author(s):  
Jerzy MERKISZ ◽  
Marek WALIGÓRSKI
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
High Reliability ◽  
Direct Injection ◽  
Combustion Process ◽  
Vibration Signal ◽  
Internal Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Railway Traction

The article concerns the possibilities of use of the method being able to assess of the combustion process and its lack in internal combustion engines of railway traction vehicles, that bases on the use of vibration signal parameters. The paper includes the results of research conducted on the engine test bench with a single cylinder research and compression-ignition engine with direct injection, and tests for the engine of a diesel locomotive in the exploitation condition. Possibility of the vibration signal estimators application to the assessment of a combustion process lack in an internal combustion engine and a high reliability of combustion process diagnostics basing on the above method have been proved.

Sign in / Sign up

Export Citation Format

Share Document